Having problems with your Dishwashers ?

My Kenmore dishwasher has the lock-on light that is stuck in the ON (lit) position freezing any other action. I have tried cancelling it, shutting off the power and resetting it with the "Heated Dry - Normal-Heated Dry-Normal" pushing of the buttons with no success. Ideas?


Answers :

I held the "Heated Dry" button down until the lock light went out. It may have been 10-15 seconds. All seems well now.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Kenmore dishwasher has the lock-on light that is stuck in the ON (lit) position freezing any other action. I have tried cancelling it, shutting off the power and resetting it with the "Heated Dry - Normal-Heated Dry-Normal" pushing of the buttons with no success. Ideas?


I held the "Heated Dry" button down until the lock light went out. It may have been 10-15 seconds. All seems well now. ... Dishwashers

I have a whirlpool gold quiet partner 3 n the cancel button won't go off n the normal wash button won't go off either. I can do a quick wash cycle on it but then goes right to sani rinse afterward n don't shut off itself it just keeps on going. Solution? Is there a reset for it because I have an air dry button but not a heated dry button so I don't kno if I should push sani rinse/air dry two times over as opposed to sani rinse/ heated dry or if there's a diffrent solution for it. This all starte


... Dishwashers

My whirlpool DU930PWSQO dishwasher won't start. Drain will work, other control panel lights work . Tried shutting power off/on and the heat dry - normal reset sequence but that didn't work. Any ideas?


... Dishwashers

Kenmore Dishwasher Model 665.11643300 Cycle will not run. Normal Wash light blinking Cancel light will also blink (but can be cancelled by holding button down) I tried shutting down the power and resetting at the breaker. I tried other buttons like Air Dry, etc to see if there was some sort of sequence Note* last cycle ran was rinse cycle many months ago - house has been vacant and dishwasher has not been in use.


I will look a bit further in detail about your dishwasher problem. I am assuming you have checked the inlet water tap to the dishwasher is turned on. ... Dishwashers

I have a kenmore dishwasher model #655.1374 or 655.1384 which is only about a year old. I am having a problem with the controls. It will not allow me to use smartwash. The only control that can be used is quick rinse. I reset it by pushing Sani rinse and heated dry. All the lights come on and it seems to do a test. But after that still the same thing except if I push start resume it goes to normal wash which stays on a long time and periodically the cancel drain light comes on as well as the 4


... Dishwashers

Frigidaire Dishwasher Hi, I have installed a new model GLD2250RDC0 Frigidaire dishwasher and it will not start. Power and water supply is connected. When I push the cycle button for Normal the light comes on but when I push Start nothing happens except the "hi-temp wash" and "no heat dry" lights flash. I assume this is some kind of troubleshooting code but the manual does not cover this and I am in Honduras so service is non existent. Any ideas? By the way, I was a builder in the States for 25 y


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

The normal wash & heated dry lights are flashing on my GE dishwasher & won't stop. I've cut the power & attempted to reset the system, but no luck. Any other ideas?


Please provide the full model number of the GE dishwasher. ... Dishwashers

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

I have a whirlpool quiet partner II dishwasher model # DU1055XTVB5 and the normal light is steady flashing I have did the sequence to reset HEATED DRY NORMAL HEATED DRY NORMAL and the normal light continues to flash and if I push the cancel/drain button then it starts a steady flash


... Whirlpool 24 in. DU1055XTP Built-in Dishwasher

A wood screw fell to the drain and short-circuited something. It caused a loud pop and sparks. I reset the control panel with heated dry, normal, heated dry, normal until all light went on. Then cancel. The dishwasher will not fill.


Sounds like your pump got fried or shorted out. ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

My kitchenaid dishwasher model kudpo2frsso built in lights are flashing normal and cancel I shut off the breaker for 20 minutes pressed Normal heat dry X2 Then cancel x2 but to no avail. Any suggestions its the day before Thanksgiving HelpI T The Normal and Cancel lights are flashing simutanuously and the dishwasher is not working at all


... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

Dishwasher: Kenmore ultra wash sensor quiet guard plus. I'm in a rental so I don't have the manual or model number. A few days ago it just wouldn't start the wash cycle. When you press normal wash then start the no heat dry and lock lights flash every other second or so but nothing happens. I can hit the cancel button and it will make sounds like its trying to drain, and after about 5 minutes stops. I've done the heated wash/ no heat dry sequence to try to reset but no luck. Also tried turn


... Kenmore Dishwashers

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

Kenmore elite dishwasher shuts off after 15 min on normal wash. NO blinking green clean light. I have tried the reset sequence normal wash and heated dry. Did not fix the problem. Control board was replaced. Still shuts off. Pls help.


... Dishwashers

My kenmore dishwasher, model 665.16473300 has stopped working. Now the lights just flash at the Smart Wash, Normal Wash, and Cancel. I've reset the power and it just comes back. I've taken the drain area apart and made sure there are no obstructions. The buttons seem to respond, as after I reset the unit (breaker), only the Smartwash button is flashing. I push cancel and then it starts flashing. So I think the buttons work, but it's locked up.


IS THE WATER TURNED ON TO THE DISHWASHER ... Dishwashers

Hi! We have a GE Profile PDW9280J0SS with electronic control malfunctions. I can't get it out of the ADDED HEAT mode and many of the other button lights won't light up. I've flipped the breaker several times, and this does (usually) reset the controls to "Normal" and "Heat Dry", but when you push "Start" it switches back to the ADDED HEAT mode. When it goes through this cycle the soap dispenser doesn't open so the dishes don't get clean. I can't use the arrows to select different types of w


Not a specific fix, but I can tell you I have this same exact model dishwasher, since 2005, and it has been services for touch pad button problems at least a dozen times. I am in fact on the phone now with service scheduling another visit because i ... Dishwashers

I have a KitchenAid KUDp02FRSS1 dishwasher and it will not respond to any buttons being pushed. The Normal, Light China and Cancel lights continue to blink. I have tried reseting the circuit breaker to power cycle the machine but when I turn the power back on it just continues to blink.


... Dishwashers

Kenmore dishwasher ultra was quiet guard 3 model 56516012403 control panel will not activate red lights blinking on normal wash and cancel drain. did the hold the heat dry button then the normal wash button, it stopped the blinking but the dishwasher will not engage when you push any button


That would be model # 66516012403 correct??you may have inadvertently set the lock on function.. check this out from your manual...Lock OnUse the Lock On to prevent unintended use of the dishwasherbetween cycles. Y ... Kenmore 15912 Built-in Dishwasher

I've got a GE model GLD4408R00WW front load dishwasher, which was not filling, even though you could hear the motor running. Tried resetting it by turning off the power at the wall switch, and then from the breaker itself, but now, see the "Normal" wash cycle and Heated dry lights blinking when power is returned...


Hi,\012Here is a tip that will help you to find out why water will not come into the dishwasher... Dishwasher Tr ... GE Dishwashers

Ge gld5800 water supply and power good, but water does not enter. Buttons for Normal Wash and Heated Dry flash on and off. Have disconnected power and reconnected to "reset" to no avail.


2 things to check, the water inlet solenoid valve which activates and allows the water to enter the machine and also check the door switch/lock mechanism, if the board doesn't think the door is closed properly it will not respond. hope this helps. ... GE GLD5800L Dishwasher

I have a KitchenAid dishwasher, model KUDP02FR. The "normal" cycle light is flashing. When I push "cancel" or "resume/start", they start flashing as well, but the dishwasher won't start. I turned off the power and turned it back on. The "normal" light still flashes, but when I press "resume" it all starts over again. Any ideas? I can't find this in the troubleshooting guide I have. Thanks.


Hi\015\012\015\012Thanks for using FixYa. To\015\012resolve this you will have to reset the console. Do this by closing the door\015\012and press these buttons in sequence...\015\012\015\012 ... KitchenAid KUDI01TBK Dishwasher

I have a Whirlpool Gold Quit Partner III, model GU1100XTLB1. When I run the normal cycle it functions well until near the end. At that time the unit stops and the pots&pans indicator light blinks. If I hold the cancel button in the unit drains then refills and the light starts to link again. I don't know how to reset this unit because I only have air dry. If I leave the power off for a day I can get the unit to reset. If not, it just fills back up with water and the pots&pans starts blinking aga


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Maytag mdb6601aww push normal wash button-- nothing happens. push other wash cycles, the lights flash about 30 times then stop-- then nothing happens. tried clearing codes. hi temp wash then heated dry , hi temp wash then heated dry. same problem. also tried normal wash then heated dry 3 times in 6 seconds--- same thing. also tried unplugging unit waiting 10 minutes with no luck. thanks


... Maytag 24 in. MDB6100A Built-in Dishwasher

My accusense light keeps coming on and blinks continuously. I tried the heat-dry, normal sequence and it would reset to 2 minutes. After the 2 minutes cycle, the accusensor blinking would begin again. Then I tried holding the heat-dry button in for 5-seconds. This looked like it worked so we set a normal cycle without heat-dry. Äll looked good, but a few minutes in, the normal light was off, the accusensor was blinking again and the heated-dry was on again! Is the unit possessed? Other id


... Whirlpool GU2400XTP Built-in Dishwasher

Here again is my model and serial it stops in the middle of the cleaning cycle Kenmore 665.16773402 serial # ft0302854 Here is how I have been resetting the dishwasher. I hit the following sequence of buttons: Normal Wash Heated Dry Normal Wash Heated Dry Normal Wash After that ? all the lights are lit up as follows: Smart Wash, Pots Pans, Normal Wash, China Gentle, Turbo Zone, Hi Temp Wash, Sani Rinse, Heated Dry, Sanitized (Green light ? not a button), Lock on (Red Light ? no


Door latch.Open and close the door to make sure the door latch is securely fastened\015\012 \015\012Hi-Temp Wash, Hi-Temp Rinse, or Sanitize options.Some models have options that may requi ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1471 seconds