Having problems with your Dishwashers ?

DISHWASHER STOPPING I HAVE A WHIRLPOOL ADG 7560/01 DISHWASHER. AFTER 4-5 MINUTES IT STOPS AND HAS A CONTINUOUS BEEPING AND THE START LIGHT FLASHES 4 TIMES THEN A PAUSE etc. I HAVE CLEANED THE FILTER LIFTED THE MESH AND CLEANED THE BOWL OF ANY DEBRIS AND WATER. I HAVE ISOLATED IT FROM THE ELECTRIC SOURCE LEFT IT FOR 10 MINUTES AND STARTED IT AGAIN TO FIND IT DOES THE SAME . LOST IS THE WORD THAT SPRING TO MIND. HELP!! MARTIN


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

DISHWASHER STOPPING I HAVE A WHIRLPOOL ADG 7560/01 DISHWASHER. AFTER 4-5 MINUTES IT STOPS AND HAS A CONTINUOUS BEEPING AND THE START LIGHT FLASHES 4 TIMES THEN A PAUSE etc. I HAVE CLEANED THE FILTER LIFTED THE MESH AND CLEANED THE BOWL OF ANY DEBRIS AND WATER. I HAVE ISOLATED IT FROM THE ELECTRIC SOURCE LEFT IT FOR 10 MINUTES AND STARTED IT AGAIN TO FIND IT DOES THE SAME . LOST IS THE WORD THAT SPRING TO MIND. HELP!! MARTIN


... Dishwashers

Hi! My Bosch dishwasher (SHE46C02UC/22) will not shut off. The display says "1" - like there is 1 minute left, but it will not stop. Yesterday morning I started the dishwasher at 7:30am and at 11:30am I realized that it was still running. I opened it and it still had soapy water on the dishes and had not cleaned the dishes well. Any ideas?


... Dishwashers

My GE Max dishwasher is not cleaning my dishes. There are food particles left on the dishes, and the dishes themselves are not cleaned very well. The bottom of the dishwasher has food particles left ont he screen once its done. I run the hot water before starting the dishwasher, I use gel detergent because the powder gets caked in the dispenser. Where do I start to troubleshoot?


Not enough water water valve screen plugged inside inlet ... Dishwashers

The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers

Maytag mdb9150 dishwasher stopped at some point last night--found it this morning with flashing lights--I think "clean" and "heated dry", not sure.  I used "drain/off" to make sure there was mechanical noise--there was, so I don't think the machine is dead.  Purchased on 2001 with 5 year warranty, so out of luck there.  I tried turning off the electricity to the unit for a few hours; nothing improved.  When you start it (or think you have!) it makes noises for about a minute that sound promising


Check pump and solonoids click/work, if no mechanical noise, could be the circuit board, but they can be expensive. :(\015\012if the solenoids click, and allows water in, then the pump might be jammed, with grit, clean and reinstall... good luc ... Maytag 24 in. MDB9150A Built-in Dishwasher

Kitchen Aid Dishwasher - model: KUDPO2CRBLOrn Ran the dishwasher twice on pots/pans cycle and sani rinse with a special cleaner recommended due to build up and items not getting clean. (soap left all over them) Cleaned machine out great! Now, the only choices that will light are "quick clean up" and "rinse only." Even if I choose them, when I hit the "start" button - the machine will not start. No other lights will light. Machine will not start. Any ideas?? Thank you!!!


... KitchenAid Dishwashers

We have a Nautilus dishwasher which we kept during our kitchen renovation. When the dishwasher was installed back in it was tested and all was okay. However when the guys left and we started the machine it was for 98 minutes as against the usual 90 minutes. We were happy with this but now we find that at the end of the full cycle it does not turn off and continually beeps. It will not turn off by pressing the off button and you have to open the door. When you start again it immediately starts wi


Hi\015\012\015\012To reset you can leave the unit unplugged for 1hr, then plug\015\012it back in, you can also reset the controls by pressing the AIR DRY/RINSE\015\012ONLY/HEAT DRY button for 15 seconds. If the issue returns then the circ ... Fisher and Paykel Dishwashers

When I start the dishwasher, it sounds normal. A few minutes after it starts, it makes a loud, thumping noise that lasts for several minutes. After a while, it stops making noise, but about half way through the cycle, it starts making the loud, thumping noise again. It's loud, annoying, and does not get our dishes clean. We have to wash several dishes by hand AFTER we have run the dishwasher.


I have made the assumption that your d/w is a siemens machine, however if not pls repost with the make and model.\015\012There are a few possibities...check the spray arms are clear by removing any blockages in the holes, check that there ... Dishwashers

Hello, We have a combination oven and dishwasher. Last week I filled up the dishwasher and after about 5 minutes a blue spark came out at the bottom and it cut the electricity off. Once the electricity was restored we started it again and after a few minutes it just stopped after filling up with water. It blew a fuse again but only one fuse this time and now doesn't switch on anymore. We have emptied all the water from the dishwasher and checked the filter, etc and wonder what could have gone wr


Hi, I contacted the Rosieres web site in France and sent a message using the link Contact Us. Here is the reply;Dear xxxxx,we advice you to contact:TELE MENAGER VIDEO SERVICE21 rue georges Doublet0610 ... Dishwashers

My dishwasher SL34A015UC / 29 does not complete it's cycle. The cycle will stop with 1 minute left in the rince cycle and continue to run for hours, showing just one minute left. The dishes are not geting clean and there is a unplesent odor inside. I can hear the water draining during the cycle. The drain line is clear and there is plenty of water in the dishwasher. Any thoughts?


... Siemens SL5A70UC 24 in. Built-in Dishwasher

Hi, The machine will not complete a cycle. I think it may have started when the power was turned off at the mains during a cycle. Symptoms are : - You can turn machine on, select a program, press start button, close door, machine appears to begin cycle as normal, water seems to load, then 2 minutes later drains, and 1 minute or so after that the machine beeps 3 times to indicate cycle is finished. Dishwasher tablet door never opens, dishes not cleaned. Have tried : - cleaning filters; - turn


It is likely the dishwasher is locked in some diagnostic program.\015\012If you provide the dishwasher model no. then I can try to find out the keys you need to press to get it out from it. ... Whirlpool Dishwashers

We have a Whirlpool dishwasher model ADG7550. It runs ok for a few minutes then it switches to the rinse setting (i.e. the furthermost left light of the temperature lights, i.e. lights from the left, 'rinse', '40degs', '50degs', '65degs', '70degs'. We may set it to start at e.g. 65degs, it does so ok for a few minutes then it switches to the 'rinse' light and starts to beep every few seconds. There are 11 beeps.


HI, There are two areas of concern here. This will be an issue with either the element, or control sector. I suggest to start with the element inspection. This will requir you use a multimeter, if possible. You will need to varify proepr element func ... Dishwashers

I have F&P DD603 with problem with bottom draw. Once a programme is selected and door is closed, the dishwasher beeps three times then tries to start itys cycle. It then starts but stops every 1-2 minutes (like pause botton has been pressed). If you press start again it starts for 1-2 mins then stops again. I have tried turning off the power and totally cleaned out the dishwasher but no change? Any suggestions?


Hi \015\012When you pull out the drawer, pay attention to the bottom near the bottom front panel, you will see a little tab. this tab is at both sides of the drawer, press these tabs in and pull the drawer fur ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a Bosch SHU43 dishwasher, about 6 years old. After starting a cycle, it will run for a while, perhaps 1/2 to 2/3 of the way through the cycle, then shut off. After 10-20 minutes it will start up again, run for a few minutes, then shut off again. It ends up taking about 12 hours for a cycle to finish. The problem started off somewhat intermittent and has gotten worse over the last few weeks. I've checked the electrical box in the front right bottom, and the connection is good. I've even


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I`m not sure since you didn`t mention it or perhaps I just interpreted it this way, but is it consistent at the same time or approximately or is ... Bosch 24 in. SHU43 Built-in Dishwasher

Dishwasher Fault Hi, My dishwasher is a Diplomat ADP8322 (which i think is a rebadged whirlpool unit) & has been playing up recently. When you start a cycle it is fine for a minute or so then it starts beeping, the rinse light comes on & the light next to the start button flashes 11 times, pauses then repeats. I have read online that this flashing relates to what the fault is, but i cannot find out what fault the 11 flashes relate to. The first time this happened i cleaned out all of the filters


... Dishwashers

My dishwasher is flashing the clean green light, however it shows it has 2 minutes remaining from previous cycle, i have let that 2 minutes run throught, but it then show up again as 2 minutes left, but still flashing clean, and i can not cancel to staret new wash cycle


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes 7 times, pauses, and then repeats. When\015\012the dishwasher doesn't sense a ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Hotpoint BC145 Dishwasher not cleaning starts to kick in but then just sticks on the "R" light flashing and cannot reset even after turning off. Itbeeps when pressing the select button sound weaker and shorter than they used to and the light does not move from the "R". On a couple of times I have tried it has reset and then the dishwasher starts but after about 3 minutes there is a low beep(not the usual beep when a programme finishes) and the washer stops and the light is flashing on the "R" ag


... Hotpoint 18 in. BCI45 Slim-Line Built-in Dishwasher

During the cleaning of our dishwasher (ADG7952 model), it started beeping and there was a F8 message reading on the panel. The water has not drained away. We have tried to clean the filter and remove excess water left. Unfortunately, we cannot find the user manual-not sure that it was left when we moved into the house. Not sure what the problem may be?


... Whirlpool 24 in. ADG7952 Built-in Dishwasher

When my dishwasher completes its cycle, there is powdered detergent left in the dispenser and the dishes aren't as clean as they use to be. This started happening after I ran a HI TEMP WASH with a SANI RINSE cycle. I'm thinking that either the detergent dispenser door is opening late or the water is not getting hot enough. To check the dispenser door, I left the door open and just poured powder into the dispenser compartment. This did not improve the cleaning.


Hi\015\012 \015\012Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doesn't allo ... Kenmore 16372 / 16374 / 16379 Built-in Dishwasher

New SHE4AM16UC, professionally installed eight months ago. Worked fine with very light usage until now. Dishwasher starts normally but stops and signals "clean" after less than five minutes on any cycle. One inch of water in bottom that (I think) drains when a new cycle starts. Soap tablets are not ejected from compartment. Bosch authorized repairman says he now has two client dishwashers with identical symptoms and is asking Bosch support for ideas (he's changed pump, control unit, and float sw


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats.\015\012When the dishwasher doesn't sense a water t ... Bosch SHE4AM16UC 24 in. Built-in Dishwasher

Bosch SHY66C My Bosch dishwasher won't fill with water.  All electrical connections are fine and I can hear it make a sound as if it is trying to start about every 2 minutes.  There was water in the bottom so I used a shop vac and pulled it all out but it still won't start and is doing the same thing.  I checked the solenoid with a multi-meter and it appears to be working.  My power went out last night for about two hours and that's all I can think of that might have affected it.  The dishwasher


I'm a novice on this question, but i agree with the above statement about check the stuck float switch or check for a bad safety switch or lockout switch of some sort. I would suspect something is definately faulty in that area. Will the dishwasher r ... Dishwashers

Allan Dishwasher won't start. Clean light keeps flashing. I have tried cancelling a couple of times, and it goes through a 2 minute process and goes right back to the flashing clean light and not allowing it to start.


Turn off the power at the breaker to the DW and wait 15 seconds and then turn it back on and see if problem is fixed. Reboots the controller. ... Dishwashers

Dishwasher won't start. Clean light keeps flashing. I have tried cancelling a couple of times, and it goes through a 2 minute process and goes right back to the flashing clean light and not allowing it to start. I have already tried shutting off the breaker as suggested by someone but it did not solve the problem. Any other ideas?


Hi\015\012 \015\012Thanks for using FixYa. If the clean light flashes 7 times, pauses, then repeats...When the dishwasher doesn't sense a water temperature increase, it stops working and locks t ... Dishwashers

My Whirlpool dishwasher ADP951 does not start at ll. I think I turned off the machine last time before it completed its cycle. I found there was water left at the bottom unlike after a usual run. I manually removed all the water and mopped it all. yet it would not start at all as if no electricity comes into the dishwasher. Please help.


If your dishwasher is on a wall switch, someone may have shut it off, Your dishwasher could be pluged into a Daisy chaned GFI, check all your GFI in the kitchen and make sure none are triped. The home Fuse Box, make sure the braker is not triped. ... Dishwashers

Hi I have a LG LD-2052 dishwasher. It gives me an E 0 error - the water does not pump out when I open the machine after a few minutes when started to wash and message of E 0 appears? Have cleaned an


... LG Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2498 seconds