Having problems with your Pressure Washers ?

Yes, took out the unloader valve cleaned it and inspected and its fine.


Answers :

Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Yes, took out the unloader valve cleaned it and inspected and its fine.


... Pressure Washers

Karcher K3.91, lost some pressure and pulsing when trigger is release. stripped it down and checked all six valves and there all sealing as they should. i took apart the unloader valve cleaned and inspected and thats fine. there is NO water leeks anywhere or oil. preasure washer is 2 years old and gets used once a week for ten minutes. i really dont understand why its playing up


... Pressure Washers

My Miele dishwasher is about 16 months old. Initially it was awesome. Now it doesn't get anything truly clean on any rack. Every item has scum and traces of food or drink left on it. I've cleaned the filter and the no-return valve, and refilled the salt (yes, I used the right one) and rinse aid. The manual has no other instructions to remedy dirty dishes. The water is hot, and the machine seems to be running just fine. Where should I look for a problem?


The other possible problem is that the spray arms have small bits of food (sesame seeds are nasty!) stuck in the holes. Take the arms off and flush them out. You might need to poke out seeds that are stuck in the holes. ... Miele G880 Dishwasher

I have a GE Profile, GSD4930X73WW, dishwasher. The upper wash arm is not spraying well at all. I checked the water line from the pump to the upper arm and it's fine. I cleared the filters and cleaned the float. I also took the inlet valve off and cleaned the screen. Although the washer works better overall, the upper arm still does not work well. Nothing appears to be in the upper arm assy to clog water from spraying out. All seems clear from the turbid sensor (next to the pump) through t


... GE Dishwashers

Only a small amount of water enters machine when you start normal cycle. I took off water supply line at inlet valve... screen is clean, water preasure is fine.


You might have a bad water inlet valve, when triggered the inlet valve opens up to allow water to enter the machine, it's usually located behind the lower kick plate in either the right or left hand corner, if it's defective it would need to be repla ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Clean and unloader valve on Karcher hd3500 pressure washer -intermittent pressure on and off. Cleaned inlet screen. Think unloader valve is is under pressure knob? Will cleaning help?


Hi:Cleaning it is not enough. You need to make sure the o-rings are in good shape and grease it with a very very good waterproof grease. ... Karcher Pressure Washers

I have a HD 2701 DR pressure washer that starts and runs fine and usually works fine the "first" time but if you let go of the trigger and then try to use it again you just get a trickle out of the end of the wand. Usually if you hold the thing open for a while it will kick in (sometimes it takes forever...). Any ideas? It sounds like some of the "unloader valve" problems are similar but I do not see an "unloader valve" in the parts lists for the 2701...


... Karcher G 3050 OHR Gas Pressure Washer

I have a G2500VH pressure washer that has started to pulse when the trigger is squeezed. This happens if I use the 0,25, and 40 degree nozzles BUT if I use the one for low pressure(detergent use) it will hold pressure fine. I have changed the unloader valve, checked all the valves and seals ad they seem to be fine. What could be the problem?


Do you mean pressure on and off with the hp tips and smooth and steady with chemical tip? ... Pressure Washers

Honda GC190 no start. Unit has been sitting for 2 years. Drained old gas, cleaned the carb. No go. New plug gapped to 0.030in. Still nothing. spark seems good. Cleaned the fuel strainer and there IS a bit of vacuum at the fuel pump when cranking. Poured a dab of gas into combustion chamber.. Still won't "talk to me" AT ALL. Removed valve cover and checked the valves.. within specs and nothing sticking or hanging up. Timing belt and cam looks good. Took a peak at the coil.. air gap in specs. 1ohm


... Karcher 2500 PSI Pressure Washer

I have a 10 yr old ge profile dishwasher. The dishes on the top rack are not getting clean. Sometimes it doesn't even seem like the dishes are very wet I took out the upper sprayer arm and ran water through it just fine. What else may be wrong? The bottom rack cleans just fine.


Bad circulation pump. ... Dishwashers

My Whirlpool Gold Series 980 dishwater no longer fills up with enough water to drive the washing arms, so the dishes do not come out clean. I cleaned the filter on the water intake valve (which was really clogged) and it still did the same thing. Replaced the inlet valve and still no change. The water does not reach the level of the overfill float switch, so that’s not it. Its been working fine for 4-5 years, what else could it be? Thank you.


I hve provided u with all details .read it carefully .it has all the resolutions for all possibilities ... Whirlpool Dishwashers

I have a Quiet Guard Standard model #587.151524 that is not cleaning the dishes. I took the bottom spray arm and screens out and cleaned them, (they had a heavy buildup of what I would say is calcium. The arm cleaned up fine but the screen still has some areas that will not allow the water to drain. I tried CLR and it helped but the screen is still probably 60% clogged. Do you think this is the problem getting the dishes clean and if so do you have any suggestions about how to clean the screen?


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Kenmore 24 in. 15689 Built-in Dishwasher

We have had this dishwasher for approximately 2 years. Dishes do not clean well. For example, I put a mixing bowl in that I just mixed brownie in--and the bowl did not come clean (simply a thick chocolate mix). Glasses do not come clean. They always have a fine residue on the outside (food). My husband just took the (blades) out that spin and dispense water and cleaned them. The water volume seems better now. Still, if I remember correctly, the dishwasher cost around $900. It definitely


Check if the water gets hot . \012\011check if motor spins enough to give pressure water on arms to clean dishes.\012\011clean the filter regulary . ... GE Profile PDW8480JSS Built-in Dishwasher

How do you clean the unloader valve on a power washer pump?


The unloader valve usually is replaced. I dont know if you can get o-rings for it. But if you want to take it apart, there will be a crown or cap style nut just below the spring. Unscrew it completely and you will be able to remove the spool. There i ... Karcher 2500 PSI Pressure Washer

Ge Triton dishwasher GSD5500GOOWW was not cleaning like it used to- I cleaned screens at back bottom-very dirty- also-detergent cup stuck opne - took door apart and got it unstuck - it works fine now. - it seemed to do better but now it is cleaning poorly. It seems to fill and start a lot sooner than before - after 30-45 seconds it starts up. I tested the water temp and it is 90 degrees! Hot water coming in is at 105 degrees. Also - it is leaving a white residue on dishes - didn't do that be


Hi,The scum, film and white\012residue problems have started since the reduction of\012phosphates in dishwasher detergents.Here is a tip that\012will help you to solve the problem of films, residue, and scu ... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

Hello - I have a LG LD 2060SH and wanted to clean it completely - sadly I have a part called the Valve or Float Component (small white plastic thing!!!) and I can't locate where it should go! Yes, I undid all the bottom filters on the water inlet system and spray arms, they were all clogged even after special cleaning - Can you explain where it goes as I put everything back together - now it is all squeaky clean! I knew I should have taken pictures along the way, but I was so happy that everyth


There should be a little hole in the bottom of the DW and it simply slips back into that hole. ... LG Dishwashers

I have a GE dishwasher (GSD4020Y70BB) new in 1996. I replaced the whole motor assembly in 2007, seal was leaking. My dishes are not getting clean now, dried food left on plates, coffee stains in cups not being cleaned. I removed main spray arm, found nothing, turned washer on and plenty of water gushing out. I took the cover off sump all clean. I removed the filter screen in the back, there appears to be a valve with some soft rubber around it. Water gushes out of this, does stop during the cyc


Have you checked the drain pump impeller and drain hose? I am curious if there is a back siphon from the drain hose or the waste outlet at the garbage disposal might be blocked or plugged with food debris.\015\012I wou ... Dishwashers

Dishes and glasses not getting clean. Visaul inspection; it lloks fine. Removed filter and bottom perforated filter panle and cleaned off mineral-like residue. ran test program: result flashing lights for Clean & rinse/dry buttons. not sure of next step...help please.


Hi,The scum, film and white\012residue problems have started since the reduction of\012phosphates in dishwasher detergents.Here is a tip that\012will help you to solve the problem of films, residue, and scu ... Bosch 23 in. SHU3307UC Built-in Dishwasher

Model 01902 2350 psi . engine runs fine , sprays out nozzle but lower pressure and water sprays out plastic elbow on relief valve , that is supose to **** in soap if used , cant hold finger over spray from elbow , high pressure , took apart relief valve and plastic valves all orings are ok , brass pump seals look ok , all back together , still blows out elbow . ?? plastic spools were out by somebody else , not sure if they are in right , cant find picture to compare .


It sounds as if the non return valve in the elbow is the wrong way around .The o-ring normally goes in first then the ball then the spring. Try it and good luck. ... Pressure Washers

CLEAN OR REPLACE UNLOADER VALVE


... Karcher Pressure Washers

A GE triton dishwasher causes hammer noise when stops filling. The sink faucet works fine as do all the other faucets in the house. I cleaned all of the traps in the dishwasher. Because the sink works, I don't think it is a sink valve problem. I turned off the water to the house and drained the system, the air chambers should be good. Is there some component of the dishwasher that could be causing the noise? Would cleaning the pump help? If so, how would I do that?


The cause of the hammering noise, (slamming) is due to the water inlet valve on the Dishwasher (DW) shutting off abrutly once the DW reaches the proper amount of water.\015\012\015\012If this is an older DW, you might want to replace the ... GE Dishwashers

My GE dishwasher, model # gsd2230f00ww won't drain. The spray arm is working and i hear the motor. Checked both ends of drain hoses, very clean. took sum cover off, clean. checked float, fine. What could be the problem? solenoid? I turn the dial on the washer and the solenoid does nothing, should it make a noise to actuate the drainage? please help! Thank you


... GE Nautilus 24" Built-in Dishwasher

The dishwasher won't fill with water. We took the water inlet valve off and cleaned the filter screen. The dishwasher worked about 2 times and started doing the same thing. We then replaced the water inlet valve and again, the dishwasher worked a couple of times and now we're back to it not filling again. What could the problem be?


Check the float assembly, that will trip and stop water from coming in. May have soap or grime holding it up. ... GE 24 in. GLD6260LSS Stainless Steel Built-in Dishwasher

It is not cleaning dishes. I just took out all in bottom and cleaned really well. Loaded the dishwasher, started it and it sounds like it is working but the dishes are dry. There is water in the bottom and it does drain fine.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. First of all please check the\015\012Water temperature by using a thermometer inside the dishwasher to measure ... Frigidaire Dishwashers

The top cleaning bar will not spin---water is moving through it but it wont spin--the bottom cleaner spins fine---took it apart and there is not blockage in either of the cleaning bars


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Whirlpool DU1055XTSQ Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1156 seconds