Having problems with your Pressure Washers ?

No water is coming out of the pressure washer

\015 The motor is working and there are no kinks in the hose\015

Answers :

I think you have a blocked nozzle on the lance, get a paper clip and push it right down the end and wash out.
Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Briggs and Stratton Troy Bilt gas pressure washer one year old. I can get water thru pressure washer and bleed the air, water comes out the hose just fine until I start the pump. Then, I lose all water flow. Pump runs fine but when it's running, no water goes through.


... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

I have a campbell hausfeld 2450 pressure washer with water coming out of a brass hose nozzel right next to where you screw the high pressure to the pump as soon as you turn the water on from the house, start it up and high pressure comes out of it and the hose about half pressure, any ideas?


This is called the chemical injector which enables you to insert the hose for you to dispense the soap and or chemical by utilizing a soap nozzle .apparently inside this barb you will find a ball a spring and a o-ring,find the replacement parts or ki ... Campbell Hausfeld Pressure Washers

I have a Comet BXD 2525 G pressure washer pump which is giving me some problem. (Maybe) I hook the water up to pump and the pressure hose up to the pump, turn on the water and the water sprays out of the water connection at the pump. I check the hose to see if it was clog ok and the next was a the water connection ok. It's like the water is not going int the pump. When i start the pressure up the water come out of gun but no pump running like it should. The next thing i was going to look at i


The water inlet needs a gasket like all hose connections. If its gone the pump may be starving for water. ... Comet Pressure Washers

Frigidaire built in dishwasher model PLD2855RFC1. Have to wash dishes pretty much spotless prior to using dishwaser. Glasses come out with what appears to be soap residue regardless if powder or liquid. Did not use a gauge but water pressure in rest of house is good, recently replaced water heater, pressure regulator and just replaced the dish washer water source valve. Washer is about 18 months old, has never worked really well.


Hi, \012\012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms online and ins ... Frigidaire PLD2855RFC Dishwasher

I have a 2300 psi gas pressure washer, campbell hausfeld, runs fine but water comes out the nozzle like a hose , no high pressure. inlet filter is clean and when you pull the trigger on the nozzle water comes out like a hose but no pressure


If you no longer have High Pressure coming out while machine is running, it's a pump issue. ... Campbell Hausfeld PW2575 Pressure Washer

Water runs out of the pressure washer. it still has water come through the nozel but no pressure. water runs out of the washer itself


... Karcher K2.26 Electric Power Washer

I have a Husky pressure washer with a Honda 2600psi engine. Problem is, no water will come from the pressure hose. I connected the water w/out the pressure hose and water flows thru strongly. I then connected the pressure hose w/out the wand and water flowed thru the hose fine. When I connect the wand and pull the trigger, nothing. I have replaced the wand and that was not the problem. Please help.


Check the quick disconnect to the wand these are spring operated and can get stuck ... Pressure Washers

Dear Sir?madam, I bought a CV-240 4 MBC HONDA PRESSURE WASHER , 2400 PSI , 5.5HP, It is 4 stoke overhead, cam single cylinder , October, 2010 from NATIONAL HARDWARE SUPER CENTRE – GUYANA. I used this equipment sparingly during this year. I have 2 – 450 gallons plastic water tanks to supply the pressure with water. Recently, water is not coming out through the pressure hose. I talked to a technician, and he opened the water pump and there is some white plastic valve, one was broken and he repl


... Karcher 2500 PSI Pressure Washer

Karcher K6.50 Water coming from body of washer resulting in loss of pressure. Leak slows down when washer is used - ie water is coming out of jet


... Pressure Washers

I have a Honda gc160 5.0 pressure washer. All fluids are fresh. Water is hooked up with plenty of pressure but the water pressure is up and down then goes completely out. No water will come out of the wand? Please advise. Thank you.


Needs new pump ... Karcher 2500 PSI Pressure Washer

Assembly plans for karcher 2400 psi pressure i recently had a problem, with my pressure washer. i was cleaning out my hose and took the hose assembly and brass fitting off. run water threw it thought i had cleand it out, put it back together and now when i hooked my water hose back up the water comes out of the despencer instead of the pressure wand. does eny one no what i need to do to revurse this?


... Honda Karcher G2400HH-R Pressure Washer

Using a Bosch 1600W Pressure washer Aquatak 110 plus Was adjusting the twist pressure sleeve to get HIGH pressure and water supply stopped and sleeve seems fixed/seized. I turned power ON and OFF and turned water tap ON and OFF but still no water coming out of the nozzle. What do I do now?


... Pressure Washers

Karcher 3100 pressure washer, motor runs fine but when I squeeze the trigger on handle, high pressure pump won't come on unless I remove tip and water is coming out of wand without restriction. Help anyone have any ideas? It did come on once but when I let go of trigger it wouldn't come back on.


... Alfred Karcher Quick Connect Nozzles 2600 3100 Psi 5 Pack

No high power water pressure coming out of my model #580.768030 pressure washer. The same pressure comes out when the pump is turned off.


You should dismantle and clean the manifold from the pump , it is sticking. Common ... Comet BXD2527 Pressure Washer Pump

We have a Pressure washer 2600 PSI it is hooked up to the water line and we have a bucket of mix of 50% bleach and 50% water there is no suction coming from the line into the washer to mix with the water Why?


You need a soap nozzle to lower the psi is call downstream injection. ... Electric Pressure Washers

I have a Northstar pressure washer powered by a honda GC160 engine. The last time i used it, water leaks from the bottom of the unit, whether it is running or not. When running, the pressure is fine. I have felt underneath and it appears that the water is coming from the second opening from the rear. Is there a pressure relief valve there. I have a manual but cannot find any descriptors for underneath the motor.


This is a piston seal issue. You can get a kit to rebuild the pump. ... Comet AXD 3020 G Pressure Washer Pump

How to fix/grease an unloader valve on yorur pressure washer .I pull my trigger on my pressure washer gun and it clicks with water stream coming out then goes to high pressure.this is a kacher reman unit.I was wondering if this is normal or does it constantly hold high pressure


... Karcher 2500 PSI Pressure Washer

Hot water coming out of a cold water pressure washer


This sounds like a heat transfer problemYou should check that the oil reservoir for the pump has oil in it. It sounds like it may be low. Also, if it is a gas model, the engine oil may be low. Remember the pump oil re ... Porter Cable Pressure Washers

Power washer starts, water to washer on but no water pressure come out the hose


This with the engine running? If so there eigther is a restriction in the main water feed or the pump is damaged or possibly needs to be rebuilt. Did you know you can never start the mechine with the water hooked up and on full and you should trigger ... Briggs & Stratton Power Products 1539 Pressure Washer

My Troy Bilt power washer (using Honda GCV160 engine) has no pressure coming from the pump. I checked the water flow, everything seems fine. I believe the pump needs oil added, however, I can't seem to firgure it out (how to add oil to the pump). I did notice that previously, I used to see drops of oil coming from under the pump. I I have a bad seal, can I add oil and test the pressure before I change the seal? Please advise.


I had a similar problem. Turns out I had left the hose disconnected and some sort of wasp built a paper type nest inside the washer tube that the hose connects to. I had to take the pump off and take apart and then cleaned it out with a screw driver. ... Honda Black Max 2600 PSI Pressure Washer

When I pull the trigger on the pressure washer no water comes out, but when I take the attachment off, water comes out just fine. It seems as if the trigger isn't working or there is a blockage in the tip. How can I know which it is?


... Ace Hardware Pressure Washers

The pressure washer motor is running and water is flowing through but there is little to no pressure on the water coming out


Pour liquid TSP into the fresh water port (where the garden hose connects) and let it sit there for a couple of days.\015\012This will clean all the calcium and lime deposits within the pump.\015\012This is how I fixed my pressure problem ... Honda Pressure Washer PSI 3000

I have a Karcher 3.99 Pressure Washer. The motor appears to be working and water is passing through the machine when turned to the detergent application setting. However when the lance is tightened to turn on the pressure, no water is coming through. The Karcher is just over 1 year old David


Hi I have a karcher 3.99 the motor comes on and water comes out however thre is no pressure i have tested the lance on my brothers washer and this is ok what is wrong ... Karcher K 5.85 M Electric Pressure Washer

My Karcjer 2.94 pressure washer is not reaching out put pressure. The motor comes on every now and again. The motor doesn't come on when I pull the trigger. I have cleaned the filter and checked water supply. They appear ok


... Pressure Washers

I can't get the pressure washer to start up. The water is coming out of the hose, but there is no water pressure


If the washer is the kind that shuts off completely when the pistol grip is released, the problem is likely the little pressure sensor located near the output fitting (the threaded part to which the hose connects). The sensor is a little plunger held ... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1422 seconds