Having problems with your Pressure Washers ?

No water/pressure Motor runs and pumps for a few seconds then the revs increase and pressure and water fail as if there is no supply.There is a good supply and the input filter is clean


Answers :

Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No water/pressure Motor runs and pumps for a few seconds then the revs increase and pressure and water fail as if there is no supply.There is a good supply and the input filter is clean


... Pressure Washers

Bosch Exxcel model number SGS46E12GB had the check water light on a week ago, checked supply and cleaned filters, all good. light still on, got upset and slammed the door, light off. since then the unit will either wash stuff, or not. didn't seem the arms were spraying very well when I opened the door, so I bypassed the door switch tonight and put it through a pre rinse cycle. (I ran it with the bottom filters removed) upshot is the pressure of water was really poor. also, when I first turned


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

MY DISHWASHER HAS NO WATER GOING IN TO THE UNIT IT HAS HAD THE FILTERS CLEANED AND ALL OF THE SPRAY ARMS CLEANED REALLY GOOD DISCONNECTED THE WATER SUPPLY AND FOUND OUT IT HAS A LOT OF PRESSURE JUST NO FLOW ANY IDEA


Hello thereyes i have a pretty good idea i think your problem is that your water solonoid valve has failed and is shut when these solonoid valves fail they automatically shut resulting in no water flow I recommend that you turn of ... Kenmore Dishwashers

Folks, I have a Karcher 5.55 home water blaster that pulses at the highest pressure on the vario power spray wand. It works fine on the lower pressure settings and with the rotary spray wand. I live in a temperate climate, depressurize and drain after each use, always prime the pump, have good water supply, cleaned the filter etc etc. Any pointers on to do or test next? Any help greatly appreciated.


... Karcher Pressure Washers

Karcher Pro Line HD3000 pressure washer ...engine keeps cutting out when spray wand is at full power.. fresh gas, oil is good, cleaned air filter, inlet water supply is strong


... Karcher G3025OH Pressure Washer

I have error E:15 with a flashing water tap sign - I've tried the following: a) Clean filter at the bottom - now flushes out with b) remove power - return power c) remove and clean fiter for incoming water at a sort of valve Nothing! when I attach power it continues to flush out (even without water) if I put water in it evacuates without problems. The tap does supply water I've check and with more than sufficent flow and pressure! ...Help .....Thanks Gary


Hello Gary,\015\012\015\012You didn't specify the brand or model number of the dishwasher, but I suspect it's a Bosch, in which case the E:15 error with the flashing tap sign and the drain pump running continuously means the anti-flood pr ... Dishwashers

I have an LG dishwasher, model LDS 5811ww. The machine fills with water, then stops filling when the error code IE comes on. I have cleaned the inlet filter and the whole inside of the tub, by taking apart the sump filter. There is good water pressure filling the tank. When I turn off the power and restart any cycle, the pump will empty the tank, then begin filling the tank again...until it is stopped by the error code IE again coming on. The other thing I notice is the water level in the tub.


Sounds like you either have a dirty or faulty water level sensor or water temp sensor. Most likely a dirty or faulty water level sensor ... Dishwashers

Top Rack does not clean, Pump was just replaced. No Error codes. Heat is good, house water pressure is good, drain is good. I've cleaned the filter.


You do not say if the drain pump, the main motor, or the entire motor / sump assembly was replaced. If all the holes in the upper spray arms are clear, replace the VIRO motor. It is a small motor next to the main motor, and it switches a water valv ... LG Dishwashers

I have a brand new Miele dishwasher which has worked grate since it was installed 2 weeks ago. It keeps shutting itself off & indicates an F13 fault. I looked in the manual, see that water is going in fine & pressure is good. It then says to clean water intake filter. How do I get to that ? I don't have a user maintenance manual. I'm on city water & doubt that the filter is clogged but My wife will kill me if I don't get it fixed today. Can anyone help. Glenn


On my Miele 1220 dishwasher, the inlet filter is inside the inlet hose connector, where it screws onto the water supply. To clean it:\015\012\015\0121. Turn off the stopcock.\015\0122. Unscrew the inlet hose.\015\0123. Remove the black rubber s ... Dishwashers

My SE53200GB/01 fails to input water. I have checked the inlet supply hoses and filters and they are clear. I have tried different programmes and they all activate but the water fails to enter the main chamber. Any ideas what may be the problem. Could the Aqua-Stop mechanism have kicked in and if so, how do I rectify it? Thanks


Your aquastop system is activated :deactivate by turning off the water supply, running the dishwasher so \012that it is expecting to fill (if you hold the grey square box at this \012point, you should feel it slightly vibrating, which is a good sign ... Siemens Dishwashers

We have a Sears Ultra Wash III dishwasher, model 665.1677993, bought in October, 1995. It is not filling with enough water to get the dishes clean. I took the water valve out and looked at it and it seems okay. It doesn't look like the valve is opening all the way - just my guess. A small stream of water comes out with good pressure, but it is a small stream. I can't find any screens or filters in the water line coming in. The fill cycle lasts only about a minute. Is that adequate? Steve


There should be another letter after the p in your model number. If it's just a B then there are no parts available for that model. Typically a dishwasher will fill for 90 seconds or more. One minute or less sounds like you have a control board is ... Whirlpool GU2400XTP Built-in Dishwasher

I have a Neff Dishwasher and I think the problem is due to the cold water inlet valve. When the dishwasher starts it drains any water and then should stat to fill. If I monitor the voltage to the valve it does switch to 240V but still fails to fill. I have verified that the cold supply works OK and the filter on the inlet is clean. The dishwasher is a NEFF GB5121 and is about 20 Years old.


... Dishwashers

Dishes all cloudy and spotty. Maytag Intellisense plus 1996 dishwasher. I have real hard water that leave white calcium build up. I can remove and clean all of the lower spray arms and filter. How do I remove top spray arm to remand remove deposits? The motor sounds good, hot water, fill ok. On the inside top of center of arm where it meets the center input connection there is gunk to remove. How do I get to it? remove arm? thanks


The problem is hard water. Go to www.dishwasherfilter.com. They have a new product out that solves this problem once and for all. It filters the water entering your d ... Danby 22 in. DDW399 Free-standing Dishwasher

Hi. I have a Briggs & Stratton 2800PSI gas pressure washer. I can get it to start, but after about 5 min, then it quits. I have cleaned the carb, change oil, changed plug, new gas, cleaned/checked air filter. Nothing will keep it running. Wondering if it may be not enough water pressure, but would that cause it to stop like that? When it runs, it does a good job, but it stops just as you get going. Do you have any other suggestions? Thanks!


If it wont start, check for spark.how you do that,ok take the spark plug wire out put it close to the sparkplug(use some gloves or something to insulate your self from get electric shot from the spark) find some one who pull the start rope, if you do ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Bosch Exxcel Diswasher SGS43E08GB/43. Top spray bar won't spin. All arms, spray holes, ducts, filters, etc are clean and free from obstructions. Water comes out of the holes on the top bar but it won't spin. Water pressure inside the machine with all the bars and ducts removed seems good. Bottom bar works fine. Any ideas please?


Try starting the washer, then opening to door and checking the water level in the bottom of the machine, as far as I know, there should be enough water there to disolve the tablet when it sits in the bottom. if not that much, bung in a few cupfulls a ... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

My Karcjer 2.94 pressure washer is not reaching out put pressure. The motor comes on every now and again. The motor doesn't come on when I pull the trigger. I have cleaned the filter and checked water supply. They appear ok


... Pressure Washers

Washer fails to start. Power o.k. and water supply on. Filters cleaned. When set to start makes regular sound as if trying to start cycle. Any advice please?


Hi.Check if the water is flowing inside machine or not.If the tub is not filling, test the water level device (usually a float switch located on a side inside the tub).Ensure that the switch is not stuc ... Zanussi 23 in. ZDT6252 Built-in Dishwasher

Intake/Drain light is on. First flashed F13. Cleaned the water intake filter;cleaned the triple filter and drain pump.Light continues to stay on-it seems as if no water in coming in the dishwasher. Water supply is on all the way.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. F13 is a\015\012flow meter error; unfortunately there is no way to reset it so you’ll have to\015\012get ... Miele Dishwashers

I have a 2300 psi gas pressure washer, campbell hausfeld, runs fine but water comes out the nozzle like a hose , no high pressure. inlet filter is clean and when you pull the trigger on the nozzle water comes out like a hose but no pressure


If you no longer have High Pressure coming out while machine is running, it's a pump issue. ... Campbell Hausfeld PW2575 Pressure Washer

Have a LG model LD-14AW2 dishwasher which has done good service for many years However, it now sems not to have enough water pressure to operate all the rotary sprayers at the one time - thereby not cleaning properly Have purchased a manual and raken the whole machine apart looking for a partial blockage of the water ways - non found - all looks perfect - still no water pressure I would suspect the pump - however, would have thought a pump either gave full service or stopped - not parti


Hi The issue seems to be with the float switch assembly that is bad and should be replaced. Float assembly is found inside the dishwasher's tub, on the bottom. The water that ... Dishwashers

F&P Nemo dishwasher. Srart/reset light blinking 4 pulses. Program select knob won't rotate to select wash, rinse only available. Unit is clean, filters clean, water supply filter clean. I am an electrician but owners manual doesn't help.


... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

I have a Karcher K3.48M electric pressure washer which used to shut off when you weren't using the cleaning wand. This no longer happens and there is alot of water running out of the bottom of the unit. (This didn't used ot be the case) I expect a leak somewhere inside the unit, but I'm wondering even more if there is a pressure switch which has failed that cased the leak. In other words, if I find and repair the leak and there is a failed pressure switch, it will likely only break again. I can'


Hi you will have a 8 digit number on a silver plate on the machine with a number like 1.141-470.0\015\012Then go to www.karcher.com then on the left click on Europe, then you ... Karcher PSI Electric Pressure Washer

My dishwasher (Kenmore Elite 665) doesn't use up all the detergent in the detergent cup - it always leaves a little behind at the end of the cycle. the dishes don't get quite as clean any more, either. I recently replaced my old water heater - we were getting lots of little plastic pieces in our faucet screens. I'm guessing that the water pressure may be low, and that it may be due to the same problem. Is there a screen-type filter that filters the incoming water, before it enters th


I don't believe you have a screen at any water feed and doubt that would be the problem. Once the washer fills the pressure to the cleaning arms is provided by the pump itself. I have this issue every couple of months due to hard water and the calci ... Dishwashers

DW fills up with water after sitting. When I turn off the water supply it does not fill up. Removed solenoid valve and cleaned the filter and check for possible blockage. Put back together and turned on water supply. did not fill up until we used it for the first time after my fix. Could the solenoid valve not be sealing off completly DW is a Bosch SH5316UC/U12


... Bosch Dishwashers

I have a Miele 590G dishwasher. Everything appears to work except for water supply. Any suggestions about what I could do or what could be broken? I opened the supply connection (the small gray box) and checked the filter - all seems good. But still - no water supply! Thanks in advance. Ross


You must to check also the tap of water which connect water to this small box may the water pressur out from tap is weak .\015\012you can use a small pan to help this test.\015\012 thanks ross ... Miele 24 in. G656SCi Plus SS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1991 seconds