Having problems with your Pressure Washers ?

I have a Briggs and Stratton 5.5 hp 2250 PSI pressure washer that lacks PSI. How do I make sure the upload valve is free. It just doesn't appear to be adding pressure to the tank.


Answers :

Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Briggs and Stratton 5.5 hp 2250 PSI pressure washer that lacks PSI. How do I make sure the upload valve is free. It just doesn't appear to be adding pressure to the tank.


... Pressure Washers

I have a 4,000 psi, 4.5 gpm 45G cat pump powered by a 13 hp honda engine I can not seem to be able to adjust the unloader valve to give me pressure over 950 psi and even at lower pressures, the pump will not deliver consistant pressure without bouncing off to the relief stage and back into the tank Are unloader valves worth repairing, or should i look at just buying a new one my current thought is to buy an EZ start Pulsar


I would just purchase a new unloader valve, they usually aren't worth rebuilding. I would like to have a picture of the set up that you have, if you can send me a picture of the unloader region of the pump I can get you are price on a new one. email ... Honda Pressure Washer PSI 3000

Dear Sir?madam, I bought a CV-240 4 MBC HONDA PRESSURE WASHER , 2400 PSI , 5.5HP, It is 4 stoke overhead, cam single cylinder , October, 2010 from NATIONAL HARDWARE SUPER CENTRE – GUYANA. I used this equipment sparingly during this year. I have 2 – 450 gallons plastic water tanks to supply the pressure with water. Recently, water is not coming out through the pressure hose. I talked to a technician, and he opened the water pump and there is some white plastic valve, one was broken and he repl


... Karcher 2500 PSI Pressure Washer

Started by Craftsman 2700 PSI , 2.3 GPM Briggs & Stratton Powered Pressure Washer for first time in 9 months. Added new oil, and gas. started but is smoking from muffler and is dripping what appears to be oil near the exhaust end. I shut it down. What could this be due to?


The first thing I would check would be the oil level, to make sure you didn't put in too much oil. If the oil level is correct, it could be a stuck piston ring, letting oil blow by the piston, and out the exhaust. If this is the case, you are going ... Craftsman 2700 PSI,2.3 GPM Briggs & Stratton Powered Pressure Washer - Ca. Model

Honda 2700 psi GC160 pressure washer will start with starter fluid in carburetor but wont stay running? Changed sparkplug cleaned carburetor, Added fuel cleaner then let set and drained all fuelandadded new. Seems as if their is no fuel going from the tank to the carburetor?


... Pressure Washers

Hi I have a brand new Honda Power washer GC 160,2600 psi 2.3 GPM my husband taught me how to use it last night and I think I have followed all of steps: 1. hose free of kinks 2. connected to machine 3. purged pw handle of air and made sure water from house coming through 4. pulled out choke 5. turned red button to "ON" position 5. pulled T handle enging starter and it sounds like it will start but doesnt what am I doing wrong??? yes it does have gas in the fuel tank.


... Karcher 2500 PSI Pressure Washer

Samsung dmt800 dishwasher error code 4e. Water valve is open, pressure and temp correct, flex water hose not kinked, water inlet valve is free of debris. next steps? replace water inlet valve?


... Samsung DMT800RHW Built In Dishwashers

Model 01902 2350 psi . engine runs fine , sprays out nozzle but lower pressure and water sprays out plastic elbow on relief valve , that is supose to **** in soap if used , cant hold finger over spray from elbow , high pressure , took apart relief valve and plastic valves all orings are ok , brass pump seals look ok , all back together , still blows out elbow . ?? plastic spools were out by somebody else , not sure if they are in right , cant find picture to compare .


It sounds as if the non return valve in the elbow is the wrong way around .The o-ring normally goes in first then the ball then the spring. Try it and good luck. ... Pressure Washers

No pressure i have a karcher g 2600 vh i wasnt getting pressure and i found that my spill valve was faulty it was actually broken i bought a new one installed it and im still not getting much better pressure ive taken the pump apart and checked for build ups blew thru the valves wirh the compressor and there appear to be no blockages


... Karcher G 2600 VH Gas Pressure Washer

I have a G2500VH pressure washer that has started to pulse when the trigger is squeezed. This happens if I use the 0,25, and 40 degree nozzles BUT if I use the one for low pressure(detergent use) it will hold pressure fine. I have changed the unloader valve, checked all the valves and seals ad they seem to be fine. What could be the problem?


Do you mean pressure on and off with the hp tips and smooth and steady with chemical tip? ... Pressure Washers

I have same problem with Chicago Electric # 47761 electric pressure washer as Aug 10 2010 writer had w/ Karcher 2500. Runs briefly then stops. Pressure is trapped in hose. I cleaned hose disassembled & greased valve in handle. No improvement. Problem appears to be premature wear of trigger cam in handle - both are plastic. Valve body is rigid nylon. Any thoughts??


... Pressure Washers

Starts ok wrench appears heats ok wash cycle pressure strong at first then fades wrench appears -p2 -cleaned screens and checked spray arms .incoming water pressure 20 psi whats wrong ?


Check the spray arm. Machine water pump. After this pump pressurebuilds up to the spray arm. Rubber hosejunction inside the wash tub. This place gets connected to the spray arm system. You can see this when you draw the tray for loa ... Hobart 24 in. LXIH-3 Built-in Dishwasher

My pressure washer doesn't have adequate pressure anymore, it was working well and then the psi pressure just stopped. It will crank up and spray but there is no added pressure, it spray the same as if the motor was off.


... Pressure Washers

I have a homelite honda pressure washer 3100 psi less than 2 months. I used it and after 2 week tried to use it again it ran fine but very rough on idle. Replaced gas and added stabilizer still rought


... Psi Pressure Washers

I have a Northstar pressure washer powered by a honda GC160 engine. The last time i used it, water leaks from the bottom of the unit, whether it is running or not. When running, the pressure is fine. I have felt underneath and it appears that the water is coming from the second opening from the rear. Is there a pressure relief valve there. I have a manual but cannot find any descriptors for underneath the motor.


This is a piston seal issue. You can get a kit to rebuild the pump. ... Comet AXD 3020 G Pressure Washer Pump

Unloader valve Thanks for the insight on my problem with a Karcher 550m. I have taken the pump motor out of the unit. How do I identify the unloader valve & replace it? There does not appear to be any other leaks. Is this the only part that needs replacing if pressure is down? Many thanks


... Pressure Washers

I have a Karcher 2,600 PSI 2.3 GPM Gas Pressure Washer G 2600 VHR that I have used once last summer. I have stored the PW in my basement with no fuel in the gas tank. The PW was never exposed to freezing temps. I cannot get the PW to start. I put new fuel into the tank, the oil is good, I drained the carburetor, and the spark plug works (tested it). I pull the cord and the engine doesn't turn. Fuel value is on, choke is pulled, and the starter switch is turned on. System is practically brand new


Hi I have a similar pressure washer from Kartcher and the same scenario as yours I have owned it for about 2 years and noticed that it was getting harder and harder to start with each time I use it which is months. If your pw has a honda engine on i ... Karcher G 2600 VH Gas Pressure Washer

Karcher 620m pressure bypass valve sticking - Karcher 2500 PSI Pressure Washer


... Karcher 2500 PSI Pressure Washer

How to adjust pressure valve - Coleman Powermate DuraBuilt 1400 PSI Pressure Washer


... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

I have a 2800 psi pressure washer and it doesnt hold pressure... Any solutions?


Go to Porter Cables website and see if they have an unloader valve rebuild kit.\012\012\012Or try a site like this one.\012\012\012 ... Porter Cable Cable Premium Pressure Washer PCH2425

I have a Karcher G2600 OR Pressure Washer, 2600 psi, 2.5 gpm. PN 1.194 506 0. gas engine works fine and water flows fine but pump is not adding pressure to stream. Checked and cleaned inlet water filter.


... Pressure Washers

Some guys at the church was using this haracher 4000 psi, I was call and was told the machine stop working and would not crank up.I use a next machine to finish the charity jobs on saturday. Sunday the machine starts up but when I connect the garden hose and turn on the water it did not comes out, where the VALVE HOSE THAT GOES TO THE WAND ABOVE THE UPLOADER, I open every bolt and water comes out except the wand valve, pump was plush out and sprayed out, so we know that water enter the pump


Where the hoses attach to in the pump is a valve along with another valve inside of it. Remove both valves and clean and relube with Vaseline or equivalent. The inner valve will be the toughest one to remove and that its why it does not work if stuc ... Karcher Pressure Washers

Bosch slimline dishwasher SRS560. Unit has had this fault for a while, now going a bit mouldy so keen to repair it. Displays following Symptoms 1) Firstly empty motor drains water. This appears to be fine as I can hear the gurgling of the plug. 2) Then takes water from inlet to fill internal tank. I can hear the water entering the tank, and tap pressure indicates that water is being taken in. 3) The unit then sits there and does nothing for 25 mins until programme ends. I've


... Dishwashers

I own a husky 2200 psi. when water flows through while the engine runs the water doesnt come out at a pressurized rate. It has minimal pressure.


Check the by-pass valve for leak thru first, then see what the pump is actually putting out for pressure.,then make sure the supply side of the pump is getting the needed flow rate of water input,if not pump vanes or seals may be defective ... Briggs & Stratton Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1099 seconds