Having problems with your Pressure Washers ?

Hi i have inherited a karcher kb9040.it has only been used 4 or 5 times so i dont realy know how it should sound when. water is suplied to it it surges when you pull the trigger you only get the presure of a good hose pipe jet should the motor speed up when trigger is pressed regards ****


Answers :

Hi there!
\015\012 when you got as good as pipe pressure,you need to accelerate the speed motor to have a good pressurise water for your purpose,the pressure washer has a surge regulating valve as you trigger water gun the pressure blow up,as long
\015\012as you pull the trigger on the pressure build up pressure it has also equipt with pressure switch to regulate pressure and for safety purpose.you can also adjust the nozzle by rotating gradually to slim the pressure water out put.have a nice day,don't forget to rate me.thank's
Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi i have inherited a karcher kb9040.it has only been used 4 or 5 times so i dont realy know how it should sound when. water is suplied to it it surges when you pull the trigger you only get the presure of a good hose pipe jet should the motor speed up when trigger is pressed regards ****


Hi there!\015\012 when you got as good as pipe pressure,you need to accelerate the speed motor to have a good pressurise water for your purpose,the pressure washer has a surge regulating valve as you trigger water gun the pressure blow up, ... Pressure Washers

Pressure Washer Purchased in 2001. Used about 30 hours. It is very hard to start if at all. Good gas, good spark plug. Sometimes it will start within 50-100 pulls. After getting started, if you release hose trigger it will cut off. Any suggestions of what else to do? Thanks in advance.


I would look into getting the carb rebuilt, sounds like there is some gummed up valves. ... Pressure Washers

I HAVE A NEW CRAFTSMAN PRESSURE WASHER WITH KEY START. I HAVE USED IT ONCE AND WHEN I TRIED TO START IT IT WAS HARD TO START HAD TO PULL START IT. NOW IT WONT START. LET PRESSURE OUT HAVE HOSE OH AND RUNNING, NEW SPARK PLUG HAS OIL, GAS FILTER FINE.HAS GOOD COMPRESSION, BUT WILL NOT FIRE GET SOME RECOIL. GETTING GAS TO SPARK PLUG AND GETTING SPARK. IM LOST PLEASE HELP.


... Pressure Washers

I have a dewalt model 67DX39G1l. Used it fine for a couple of years.Went to used it the other day and the water hose leading to it was getting so hot that it melted it.Found ot the pump gets scolding hot only after you release the trigger.As long as the trigger is pulled it works fine.If anybody can help me with this problem,please let me know.


... Dewalt Pressure Washers

Stalling Engine starts good cold, when it gets warm and you pull the trigger it dies. And it will not restart when it is hot.


Likely you air to fuel ratio is too lean, runs mean and hot but under load dies. then floods the carb.when it happens pull the plug ,kill engine :is there a lot of gas or none.remove the filter and watch the action of the carb ... Karcher 2500 PSI Pressure Washer

Pull my pump first startsthe pressure is good as soon as i pull the trigger the pressure is gone as long as i hold trigger just faucet flow let go of it pressure builds up until i pull trgger , no pre


... Annovi Reverberi RMW2.5G25D

We have a Karcher G2500VH pressure washer. If you start the engine with the trigger pulled on the spray wand it will run at full pressure until you release the trigger. after that, when you pull the trigger it will not have any more pressure than the water hose feeding it. Does it have an internal unloader valve? What is the part number?


Hi, Karcher calls the unloader valve a spill valve, this is a link to a full drawing/parts listing , and your fault description might well be a sticking /seized unloader(spill ) valve hope this helps ... Karcher 2500 PSI Pressure Washer

No kinks in the line. Vent at sink is clear. Will pump some water just not all of it. Pulled left side panel off and removed hoses-no blockage. Pulled drain hose off and turned plump on, seemed to have good pressure/volume. Is this a timer issue? or control panel? Model SHU4022UC/U06


Alright, so you have a Slow Filling Dishwasher. In order to keep small particles of dirt and minerals out of the pumps and nozzles of dishwashers, manufacturers install a small screen in the primary inlet water line to trap any contaminants. Over ti ... Dishwashers

I have a Husky pressure washer with a Honda 2600psi engine. Problem is, no water will come from the pressure hose. I connected the water w/out the pressure hose and water flows thru strongly. I then connected the pressure hose w/out the wand and water flowed thru the hose fine. When I connect the wand and pull the trigger, nothing. I have replaced the wand and that was not the problem. Please help.


Check the quick disconnect to the wand these are spring operated and can get stuck ... Pressure Washers

I have a McCulloch FH160B power washer and it no longer builds up pressure. I haven't used this very much at all. I tore it apart and cleaned everything I could find. When i pull the trigger for the spray nozzle, I get line water pressure. When I release the trigger, the power washer sounds like it starts to build up pressure. When this was working correctly, the pump would shut off when the trigger was released. Any suggestions?


... McCulloch Pressure Washers

I have a Kitchenaid dishwasher model KUDS01FLSS2. I finished replacing the door balancer cord and started the dw up and it started leaking underneath from the bottom somewhere around the middle of the unit. This is when it first enters the cycle, so there is no water inside. I pulled the DW out and look at the hoses and components under the DW and all looks in good shape and could not detect any cracks. However noticed that one of the hoses (not sure what the hose is called) that connects to the


In this Kitchenaid dishwasher model KUDS01FLSS2, the whole motor and water pump assembly simply sits (I think loose) in the bottom of the DW. From the inside, it is the round mechanism where the sprayer is mounted above the chopper, all one piece sit ... KitchenAid Dishwashers

My WHirlpool dishwasher won't drain - basin is full of water. Machine starts and runs the drain cycle, but something is clogged. I opened up the bottom, and pulled off the drain hose to the disposal, and that had no water in it, so the clog is somewhere before the water gets to the hose. If I run the dishwasher drain cycle, it is not pumping water into the hose. What next?


The clog could be in the hose,or on up in the mouth of the drain,air pressure might dislodge the clog,or dissasible of the drain pan in the machine. ... Dishwashers

Fuel pump not working when trigger pulled, all temp. lights on. checked flow switches all ok and new fuel pump coil an stalk fitted. the burner will work if the o ring removed from bottom of stalk allowing fuel through so something is stopping coil from getting 24v(it does get a nominal voltage of 10v)... anyone got any thoughts


... Pressure Washers

I have 2400psi washer gas will run w/hi pressure, when i release trigger and then pull trigger for hi pressure it will take minutes to get hi pressure, longer i run longer for pressure to come back.


Hi and welcome to FixYa. I am Kelly. \015\012\015\012First off check to see if there is an inlet screen at the house water hose connection point. Remove it and clean it then reinstall. If the screen was clean.......\015\012The u ... Honda Karcher G2400HH-R Pressure Washer

I got this dishwasher from a friend that had mice chew the hoses and i was told that it worked perfect before the mice chewed it. I replaced the drain and fill hoses plus the power cord. when i put everything back together and power on I get F1 on the top drawer and the rotor rotates and the heater plate turns on. The botton drawer does nothing with no display. I checked all the wires with a meter and found good continuity thru every pin. I replaced the main filter board. I even switched the


Did the F1 error in the top drawer disappear after you replaced the mains filter board? ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

I have a 2300 psi gas pressure washer, campbell hausfeld, runs fine but water comes out the nozzle like a hose , no high pressure. inlet filter is clean and when you pull the trigger on the nozzle water comes out like a hose but no pressure


If you no longer have High Pressure coming out while machine is running, it's a pump issue. ... Campbell Hausfeld PW2575 Pressure Washer

Pump loses pressure after you use it a while even when trigger is never lifted . i can start it up it runs good trigger pulled and then it loses pressure no cavatation


Looks like you need a new diaphpragm in the pump unit ... Northstar Pressure Washer 3000 PSI

Trigger gun does not function each time the trigger is pulled. The water supply is more than adequate, water inlet screen is clean, water pressure adequate, no kinks in hose, all attachments are clear and I am lost. Thanks


I have same problem. This is a fault of the bypass valve at the pump end. It has to be taken apart and serviced. ... Karcher G3025OH Pressure Washer

I have a Karcher 2,600 PSI 2.3 GPM Gas Pressure Washer G 2600 VHR that I have used once last summer. I have stored the PW in my basement with no fuel in the gas tank. The PW was never exposed to freezing temps. I cannot get the PW to start. I put new fuel into the tank, the oil is good, I drained the carburetor, and the spark plug works (tested it). I pull the cord and the engine doesn't turn. Fuel value is on, choke is pulled, and the starter switch is turned on. System is practically brand new


Hi I have a similar pressure washer from Kartcher and the same scenario as yours I have owned it for about 2 years and noticed that it was getting harder and harder to start with each time I use it which is months. If your pw has a honda engine on i ... Karcher G 2600 VH Gas Pressure Washer

Pull cord seems to grab and can't get it to start since it grabs too quickly..... tried pulling it out slowly and then let it feed back... no good... manual doesn't address this at all


... Karcher G 2600 VH Gas Pressure Washer

F2 Code Hey, I have a single drawer built in Fisher & Paykel dish drawer and today I pulled the spray arm, filter and large metal screen out to clean them as we have been starting to get a bit of stuff left behind after washing lately. That was all good After putting it all back in though I went to use the dishwasher and it stopped and came up with an F2 fault, I thought I may not have put the bits back in properly so pulled them out again and noticed that on the rotor that connects the motor to


Fault F2 means the rotor is not rotating. If you say some of the vanes have broken off, they could have been jamming it. This should spin freely with minimal force when installed correctly. If you removed the rotor itself, you do ned to take care whe ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Pulsating motor, turn machine on pull trigger, it works but not very good, let trigger off, and motor pulsates quite rapid


... Pressure Washers

I have a Briggs & Stratton gas power washer. This is the 1st time this year that I have used it. I put in fresh gas, hooked up the water supply. The engine started and then quickly stopped. I had to release the water pressure in the hose before I could pull start the engine. The only way to keep the engine running is to hold down the spray nozzle trigger. Once that is released the pressure in the hose builds up and the engine stops.


Sounds like the unloader is not working correctly. Try replacing it and see what happens. ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Pressure Once I have the powerwasher started and going (water to it before starting) i can't get it to go to full pressure it will prime up like it's going to go to full pressure give me just a shot of full pressure then go back down to probably half pressure and remain there then prime again for a second then back a coninues cycle! Maybe there's a seal or something somewhere I should look at. Hose and pressure from house is good, the seal whee the hose attaches to the bottom of the washer is ne


This is usually a problem with the "dump valve" defective in not being able to hold the pressure but only able to release it prematurely as it should only do so when to much pressur is built up inline. Only recommend qualified pump tech. But check pu ... Coleman Pressure Washers

I have a hoda pressure washer it stats right up and while i was cleanning the wood fence i let go of trigger during about 10 min, and the motor started dying i pulled the trigger and it pick right up again any ideal what would make that do that? but one time i let it quit and i couldn't get it started,i had to wait about 5 min. then it started back up again.thanks


A couple of things, what makes the engine change tone and revs is pressure, depending on the age, it may have excessive calcium build up in the pump, there may have also been a build up of crud or a wasps nest in the end of the hose when you connecte ... Devilbliss DeVILBISS Devap DVH2600 Gas-Powered Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0743 seconds