Having problems with your Pressure Washers ?

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started. I have the same problem. Water flows thru the pump when not running, but no flow or goes in by-pass mode when I start the pump. The pump being Troy Bilt Model 020296-01. I replaced unloader valve even. Anything else I can do?


Answers :

You replaced the unloaded valve. Are you positive you have the unloader screwed to pressure and not turned the opposite way? You will have no pressure if it is adjusted wrong. One other thing I have encountered is that the unloader has a ball bearing inside. If it is stuck you will have no pressure. Make sure that ball bearing is free.
Hi there,

Check the unloader valve. Sounds like it is sticking. The unloader is just\015\012not taking the pump out of bypass mode. It is usually a brass vlave\015\012screwed into the pump somewhere near the pressure line.

Let me know for further clarifications
Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started. I have the same problem. Water flows thru the pump when not running, but no flow or goes in by-pass mode when I start the pump. The pump being Troy Bilt Model 020296-01. I replaced unloader valve even. Anything else I can do?


You replaced the unloaded valve. Are you positive you have the unloader screwed to pressure and not turned the opposite way? You will have no pressure if it is adjusted wrong. One other thing I have encountered is that the unloader has a ball bearing ... Pressure Washers

Hi I have a Troy-Bilt Pressure washer 2200 psi model 20292. I've used it only 4 or 5 times. It ran great for an hour today then it lost pressure. Seems like the pump is not working. The engine runs fine but no pressure. The water runs through the nozzel and I blew air in the lines to make sure there is no blockage and found no blockage even in the pump lines. Any ideas. Tom


... Briggs & Stratton Gas Pressure Washer 20244

Troy Bilt pressure washer 2600psi. Engines running fine with supply line, wand, and pressure line hooked up but no water or pressure is coming from pump. pressure line is limp. What is the problem?


... Troy-Bilt Pressure Washers

Troy Bilt pressure washer model 020209 will not build pressure-have checked all screens and intake in pressure hose and garden hose from house to pump. water leaks at gun handle- took it apart and oiled piston- was ''grabby'' but now snappy but still leaks. Engine starts fine and runs fine. Please help.


A leaking gun will kill all the pressure. You may need to repair or replace the gun ... Briggs & Stratton Pressure Washers

Briggs and Stratton Troy Bilt gas pressure washer one year old. I can get water thru pressure washer and bleed the air, water comes out the hose just fine until I start the pump. Then, I lose all water flow. Pump runs fine but when it's running, no water goes through.


... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

2-yr old troy-bilt pressure washer with honda gcv160 engine. seems to run well, but when trigger is pulled get full pressure for less than 5 seconds before reducing to house water pressure. when left running, looks a black plastic pressure relief valve starts blasting hot water. appreciate whatever insight you can give. Thx


It sounds like an air lock. Try this: With the machine off, connect the hose to the washer and let it run for several minutes to get all of the air out of the hose, and to purge any air out of the pump. Shut off the water, and connect the high pre ... Briggs & Stratton Pressure Washers

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started.


Ok I wasnt satisfied w/ the previous answer so I did some digging. I took off all the hose attachments and drained the line. I then checked for any clogging in ALL the screens. As usual the wand screen was clogged. this is an easy fix w/ a safety pin ... Pressure Washers

My Troy Bilt power washer (using Honda GCV160 engine) has no pressure coming from the pump. I checked the water flow, everything seems fine. I believe the pump needs oil added, however, I can't seem to firgure it out (how to add oil to the pump). I did notice that previously, I used to see drops of oil coming from under the pump. I I have a bad seal, can I add oil and test the pressure before I change the seal? Please advise.


I had a similar problem. Turns out I had left the hose disconnected and some sort of wasp built a paper type nest inside the washer tube that the hose connects to. I had to take the pump off and take apart and then cleaned it out with a screw driver. ... Honda Black Max 2600 PSI Pressure Washer

My troy bilt pressure washer only runs a few seconds then dies.I thought the pump was plugged so I removed pump.While pump was off I ran the engine in case it was a fuel issue,The engine ran fine.Whic


... Pressure Washers

Troy- Bilt pressure washer #020209 , 7.25 Briggs & Stratton, AR water pump #SJV 3G27-1. Boggs down an cuts off acts as if motor is getting tight with wand in use or not. After shut down its easily starts up an repeats itself. Removed pump motor runs fine.


... Briggs & Stratton Power Products 1539 Pressure Washer

Shooting water out bottom nozzel when engine is running troy bilt 020337


... Pressure Washers

I have a Troy-Bilt GCV160 pressure washer. While I was pressure washing the water pressure just decreased. The unit will start and runs fine, but there is no pressure when sqeezing the trigger. I purged the water system with no positive results.


Hi and welcome to FixYa. I am Kelly\015\012\015\012First off let me say that the GCV160 is the engine model number and not the unit model number. \015\012\015\012It appears that your model number is 020415 (2600 PSI) as it is ... Pressure Washers

I have a pressure washer with a Honda gcv190 engine. The motor runs great but there isn't any water pressure. I removed the manifold and pump and found some mineral deposits and cleaned everything out and while attempting to reinstall the pump on the crankshaft I noticed the key was missing. Upon further inspection it appears that the key was missing from the beginning or had sheared off and then disintegrated. (There were a lot of metal shavings in the pump shaft recess). My main question is th


... Pressure Washers

Troy-bilt w/ rmv2.2g24 pump and honda gvc 160 engine fires but will not run until I remove the pump-pump turns by hand but is very stiff, can you help me ?


... Karcher 2500 PSI Pressure Washer

For pressure washer Model WP-2402-SWHB, SN 10132043: With Honda engine running, or no engine running, no water will pass through the pump.


Hi If no water is passing through your pump on mains water pressure and not sucking from a barrel then it will be either a blocked nozzle,blocked unloader on the side of the pump or a blocked water filter. ... Pressure Washers

Pressure washer engine running but no water being pumped


... Karcher G3025OH Pressure Washer

2550psi Troy bilt with Briggs engine. Pressure washer runs ok and builds pressure. But, when the nozzle lever is depressed the pressure is strong and then drops to a much lower pressure and a fine spray.


... Briggs & Stratton Briggs Stratton 2550 Psigaspressure Washer

I have a Comet BXD 2525 G pressure washer pump which is giving me some problem. (Maybe) I hook the water up to pump and the pressure hose up to the pump, turn on the water and the water sprays out of the water connection at the pump. I check the hose to see if it was clog ok and the next was a the water connection ok. It's like the water is not going int the pump. When i start the pressure up the water come out of gun but no pump running like it should. The next thing i was going to look at i


The water inlet needs a gasket like all hose connections. If its gone the pump may be starving for water. ... Comet Pressure Washers

I have a troy built 2450 pressure washer. The engine runs fine but I have no pressure out of the hose. Does the pump require that you put oil in it?


Do you live where it is cold in the winter? And did you winterize the pump this past winter if it is cold? They need to be winterized or pump damage can occur. ... Pressure Washers

Model 01902 2350 psi . engine runs fine , sprays out nozzle but lower pressure and water sprays out plastic elbow on relief valve , that is supose to **** in soap if used , cant hold finger over spray from elbow , high pressure , took apart relief valve and plastic valves all orings are ok , brass pump seals look ok , all back together , still blows out elbow . ?? plastic spools were out by somebody else , not sure if they are in right , cant find picture to compare .


It sounds as if the non return valve in the elbow is the wrong way around .The o-ring normally goes in first then the ball then the spring. Try it and good luck. ... Pressure Washers

Honda Trash Pump Model WT30X Stalling - 8hp engine runs for approx 5 seconds that shuts down, restarts after I hear a relay click ? oil is fine - so I do not believe that it is an oil pressure sensor. Are there any other sensors ? Does water have to be pumping through it??


Their is an oil level sensor that lasts around 3 months of use. unplugging it would solve your problem But replacing it is a night mare. and if your oil runs out It's all over. if not the oil sensor, and your spark is constant Check your fuel system ... Honda 8 HP Engine

Coleman powermate model#pw0881801 pressure washer.Engine runs good,Engine dies when you start to pressure wash.There is leaking water at weep holes at the base of the pump. can you tell me what parts are failing? thanks.


... Pressure Washers

No water pressure coming out while ingine is running. hoses/ attachments not clog. Pulled and opened pump, didn't see anything broken although noticed pump was filled with oil/lubricant but about 1/4" below top surface. Is it suppose to be filled to the top? What kind of oil is used on the pump? And how come there's no water pressure coming out while the motor is running and handle trigger engaged?


If you can find the model # then you can call tech support for free advise.\0121-888-279-9274 ... Karcher Pressure Washers

My karcher hds 745 is running but just won't build up pressure, this occurred after a really cold few weeks this winter and I hadn't put anti-freeze through the machine to winterize it. There's no water coming from the bottom of the machine when it's running as i've read that if the pump seals are faulty water will escape from the pump etc. The machine motor runs ok but no pressure is acheived on the gauge whatsoever. Any help would be appreciated. Thanks in advance Paul.


... Karcher Pressure Washers

Troy bilt pressure washer series 675 no water comes out the pump


Stuck valves inside the pump will stop water flow ... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1290 seconds