Having problems with your Pressure Washers ?

Absolutely no water pressure on Husky 2600 psi w/ HOnda motor

\015 Used only occasionally, pressure washer has absolutely NO water pressure\015

Answers :

Hook up water hose dose not pump water?
Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Absolutely no water pressure on Husky 2600 psi w/ HOnda motor


Hook up water hose dose not pump water? ... Pressure Washers

I have a Husky 2600 Psi 2.3 GPM Honda powered gas pressure washer. When i turn it on the motor runs fine, But when i squeeze the trigger the water is not pressurized when it comes out. How do i fix this problem?


... Honda Pressure Washers

Honda pressure washer model # exhp3640-1 3600psi 0=13hp has low water pressure out of triggers motor does not engage for higher pressure


... Pressure Washers

I have a Husky 2600 2.3 pressure washer with a Honda motor that is only two years old. When I connect the hose and the sprayer I can shoot water through the sprayer no problem. The second I pull start the engine the water stops. Why would water only come through when the engine isn't running?


... Honda Pressure Washers

My Husky pressure washer 2600 psi powered by a gcv 160 Honda. Engine starts no pressure other then from water source and soap is not being dispensed


It sounds like the (RMW 2.2 G24) pump has gone out. Mine had this problem after about 6 hours of use. I was able to order a new pump for around $160.00, and then installed it myself. Go figure it was just out of warranty. I think my next pressure was ... Pressure Washers

Shark pressure washer with honda 5.0hp motor when in use spraying with good pressure it the pressure shuts off and motor sounds like its about to shove a rod through the cases shut it off restart it andd the same thing occurs all fluid levels good pump and motor. water pressure from hose bib good. may b low water pres. for short time due to possible kink in hose reel not sure


What type pump oil to usefor karcher 2400 psi ... Honda Pressure Washers

Honda 3600 psi 0-13hp model # exhp3640-1 has low water pressure


... Honda Pressure Washers

I have a Husky 2600 PSI power washer with the Honda GCV160 engine that I can't get to start. It was okay when I purchased it from Home Depot last spring but now I've tried putting new gas in it, spraying carb cleaner, new spark plug, and it still won't start. I only ran it for about 30 minutes when I first purchased it. The guy at the service desk at Home Depot told me that the water hose should be attached and turned on while trying to start. Is this true or would this be starting the motor und


You can eliminate the motor by unbolting the pump from it and then if it will start the problem is with the pump or the unloading valve.If it does not start with the pump removed then you check for spark and get the carb cleaned or have a kit put in ... Karcher 2500 PSI Pressure Washer

Absolutely no water pressure on my husky 2600 psi, I use sparingly..........


Hello there:\015\012if you have already cleaned the filter for the hose than the regulating valve also has a filter assy with it too may want to check it also the nozzel will clog easily when sitting for a while. so you may want to check t ... Honda Pressure Washers

I have a Husky pressure washer with a Honda 2600psi engine. Problem is, no water will come from the pressure hose. I connected the water w/out the pressure hose and water flows thru strongly. I then connected the pressure hose w/out the wand and water flowed thru the hose fine. When I connect the wand and pull the trigger, nothing. I have replaced the wand and that was not the problem. Please help.


Check the quick disconnect to the wand these are spring operated and can get stuck ... Pressure Washers

Dear Sir?madam, I bought a CV-240 4 MBC HONDA PRESSURE WASHER , 2400 PSI , 5.5HP, It is 4 stoke overhead, cam single cylinder , October, 2010 from NATIONAL HARDWARE SUPER CENTRE – GUYANA. I used this equipment sparingly during this year. I have 2 – 450 gallons plastic water tanks to supply the pressure with water. Recently, water is not coming out through the pressure hose. I talked to a technician, and he opened the water pump and there is some white plastic valve, one was broken and he repl


... Karcher 2500 PSI Pressure Washer

11 hp honda motor on landa cold water pressure washer runs good except when trying to pressure wash the motor & pressure go up & down pulsating bbruummmmmbbbbrrruummmmbbbrruuummmmwhats the problem and how to fix it?


... Honda Landa PG 3500 PSI Pressure Washer

I have a Northstar pressure washer powered by a honda GC160 engine. The last time i used it, water leaks from the bottom of the unit, whether it is running or not. When running, the pressure is fine. I have felt underneath and it appears that the water is coming from the second opening from the rear. Is there a pressure relief valve there. I have a manual but cannot find any descriptors for underneath the motor.


This is a piston seal issue. You can get a kit to rebuild the pump. ... Comet AXD 3020 G Pressure Washer Pump

No water pressure - Simpson WB4200 Water Blaster 4200 Psi Cold Water Gas Powered Pressure Washer W/ Honda Engine


... Simpson WB4200 Water Blaster 4200 Psi Cold Water Gas Powered Pressure Washer W/ Honda Engine

I have a 3000 psi karcher pressure washer with honda engine, the problem is for a while the pressure would kick in and out, now only water hose pressure, the water supply is fine, what is the problem


Sounds like you need a seal and bladder rebuild < if you liver in a cold environmet for winters please dont forget to winterize your washres every year before winter ... Karcher G3025OH Pressure Washer

I own a husky 2200 psi. when water flows through while the engine runs the water doesnt come out at a pressurized rate. It has minimal pressure.


Check the by-pass valve for leak thru first, then see what the pump is actually putting out for pressure.,then make sure the supply side of the pump is getting the needed flow rate of water input,if not pump vanes or seals may be defective ... Briggs & Stratton Pressure Washers

Honda 2400 psi before it went out i cold tap the end of the wand on the ground and the pressure would return now when pull the trigger there is no pressure only a fine spray .its a karcher with a honda motor thanx


Hi, there is a small ball bearing inside the nozzle on the end of the lance , this can get jammed or missaligned and the nozzle orifice can get blocked , clean this or replace the whole lance with another 200 Bar lance .hope this he ... Honda Karcher G2400HH-R Pressure Washer

I have a Karcher G2600 OR Pressure Washer, 2600 psi, 2.5 gpm. PN 1.194 506 0. gas engine works fine and water flows fine but pump is not adding pressure to stream. Checked and cleaned inlet water filter.


... Pressure Washers

I change oil on my 3700 psi honda motor pressure washer motor and pump and after i done that the tigger rope is to hard to pull looks like some who is pressure some where can some one help me whit this problem .. thank you


Most likely has nothing to do with oil change. Have someone hold the trigger on handle open to relieve pressure on system/pump , this will make engine turn easier when you pull rope. ... Karcher 2500 PSI Pressure Washer

I have a 3000 PSI Honda pressure washer. The motor


Your nozzle could be plugged or partially plugged. Also, try running it with the high pressure hose taken off to flush the pump. ... Honda Pressure Washer PSI 3000

Husky 2600 PSI Pressure Washer low pressure tap water flows thru the pump and out the nozzel but no high pressure flow


... Briggs & Stratton Pressure Washers

I have a Husky gasoline pressure washer. The honda motor starts but stalls because the pressure by-pass (not the right term) doesn't seem to open and builds up pressure. I haven't tried to remove any parts yet. I think grit has got in but don't know for sure. The pump looks pretty simple and the part I want to remove for cleaning looks like a plastic hexagon nob. Will this access the by-pass or is it something else.


I think you're right about the knob, but try this:Open the water to the washer. Leave the line open, and hold the trigger down to get all of the air out of the supply and discharge lines. While still holding the trigger down on the spray gun, ... Pressure Washers

I have no water pressure it is on a husky 2600 psi 2.3 gpm 160cc gcv pressure washer and it worked fine yesterday shut it off ans went to use it today and no pressure


... Annovi Reverberi RMW2.5G25D

NO PRessure i have a Honda gcv160 5.5 dt2400cs CRANKS RUNS FINE AS LONG AS TRIGGER IS pulled to let water trough it has no pressure soon as you let go pressure starts building then it kills the motor will not run unless you hold handel


Hi It sounds to me like your unloader valve is stuck, this is the thing that is meant to move up and down when pressing the trigger.Please remove the unloader valve assembly and check for damage. If no damage is found then grease and lubricate this p ... Honda Pressure Washer PSI 3000
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1760 seconds