Having problems with your Pressure Washers ?

1600 psi durabuilt power washer, hand nozzle, gun, leaks water.

\015 1600 psi durabuilt power washer, model pw0501600. Hand nozzle, gun, leaks water profusly. Took gun apart. Two springs are inside of gun. Need to know where springs belong inside of hand nozzle, gun.\015

Answers :

Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

1600 psi durabuilt power washer, hand nozzle, gun, leaks water.


... Pressure Washers

I have a washer model 1805 (1800 PSI). Everything works but there is always leaking of water (sprays) when I use it. The leak is not from where the water hose connects to the washer, but where the black piece attached to the hose is connected to the body of the washer. I can still do a decent job of power washing, but am wondering if the leaking of water is reducing the power of the washer.


Yes, leaking water will reduce the pressure. Sounds like you need to replace the O-Ring inside the connections on the pump. This is where the pressure hose connects to the pump. If you look carefully inside that connection you will see an O-Ring. Use ... Campbell Hausfeld PW1805 1800 PSI 15 GPM Pressure Washer

My Karcher K730 MXS pressure washer was leaking water out of the rear of the gun handle. I bought a replacement hand gun and the new gun is doing exactly the same!


... Karcher Pressure Washers

At the beginning the pressure washer was running but there was no power from the nozzle. I stop the gun trigger, remove the nozzle , it works for 1 minute and stop working again Now the washher pressure turns off on its own after 1 minute or less Honda 2400 psi


See attached link:\015\012http://www.wmpcs.com/index.php?main_page=page&id=14\015\012\015\012If you continue to have the problem you m ... Honda Karcher G2400HH-R Pressure Washer

Gun I have a Campbell Hausfeld 1750 PSI (Electric-Cold Water) Pressure Washer and the water is leaking out of where the trigger is. Any suggestion to fix it?


Replace the wand (Gun) The valve is not repairable. ... Campbell Hausfeld PW1750 Electric Pressure Washer

Campbell Hausfield Pressure washer model 1549. After a few years of storage, I cannot prevent the powerful spray leaking from the connection between the Gun and the Lance. I replaced the O-Ring, and tried other means unsuccessfully. Spray from the joint is almost as powerful as spray from the lance nozzle. The Briggs and Stratton engine has been cleaned and operates well. The pump operates well. But the lance connection refuses to seal.


Hello,Most likely, the housing has split and seal is not being made. There is a chance that the hose is leaking where the fitting is crimped on (my experience, but different pressure washer). Are you able to see a leak when turned off b ... Campbell Hausfeld Pressure Washers

My Snap-On 2000 PSI Electric Pressure Washer is not working. When I hook up the water hose and plug the power cord on and turn the machine on, all I get is a leak under the machine. Is there a shop


... Pressure Washers

Have a generac 200 psi power washer and when i get it all hooked up its ready to go but water does not come out of the nozzle but pushes out other places. nothing stopping it up that i can see.


... Briggs & Stratton Power Products 1539 Pressure Washer

My karcher pressure washer 520 M is leaking water from the hand gun


You should watch the video on this blog. This is a very common problem, because the original gun/wand on many pressure washers is the same! However, Prism Teachings observed something that you should know about its design: ... Karcher K2.26 Electric Power Washer

Hand gun control leaks water - Pressure Washers


The seals in the gun need to be replaced ... Pressure Washers

The gun has busted and sprays water - Coleman Powermate DuraBuilt 1400 PSI Pressure Washer


Repalcement parts are available from Northern Tool or Grainger ... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

Durabuilt pressure washer 1600psi. Water leaking


Sounds like a faulty seal around the gun. Repair might be few bucks if you take it in. But the price of the part is probably under a buck. Depends if you want to rip apart it yourself. ... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

Powerate durabuilt power washer model db1303 - Coleman Powermate DuraBuilt 1400 PSI Pressure Washer


... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

I have a McCulloch FHH18A power washer. When plug it in without the water turned on, the pump will start. As soon as I turn the water on to the unit, the GFCI power cord trips. Water does flow through the unit as I have water at the wand nozzle when not plugged in. Any suggestions?


I would guess there is a leak somewhere inside the unit that is spraying water on some electrical component and causing a ground fault. ... McCulloch FHH18A Electric Pressure Washer

Hi ..I have an Excell gas pressure washer model no. Exwgv2121-3 with Faip 2100 psi 2 gpm vertical shaft pump..the problem is that there is water leaking from every weep hole at the bottom of the pump when running. Oddly enough,the pump still puts out significant pressure but less than it should due to the leaking water. What is the most likely cause of this?..is it the high pressure water seal(s)? If so,how do I repair it?


... Pressure Washers

Very little water flow from washer . Once water is connected to the intake side of washer very little is coming from the out site to power nozzle when engine is started it still does not boost water preasure


... Pressure Washers

Power washer starts no problem but when turned on and activating the trigger on the pressure washer gun, water no longer comes out. The gun itself was replaced not long ago. What could be the cause?


The tip could be plugged up ... Honda Pressure Washers

Why will water not flow through hose into the spray gun with the washer not started as well I started the power washer and the water still does not come out.


... Craftsman 2500 PSI Briggs & Stratton Powered Pressure Washer

I have a McCulloch FH160B power washer and it no longer builds up pressure. I haven't used this very much at all. I tore it apart and cleaned everything I could find. When i pull the trigger for the spray nozzle, I get line water pressure. When I release the trigger, the power washer sounds like it starts to build up pressure. When this was working correctly, the pump would shut off when the trigger was released. Any suggestions?


... McCulloch Pressure Washers

Leaking water The washer gun handle is leaking water when pressed,what is the problem? Can it be fixed? The model number is 015356-203.


The o-ring and the plastic insert is broken. They may not have a part replacement, may have to get a new gun. Take the gun apart and you'll see the problem. ... Karcher K2.26 Electric Power Washer

I have a 2300 psi gas pressure washer, campbell hausfeld, runs fine but water comes out the nozzle like a hose , no high pressure. inlet filter is clean and when you pull the trigger on the nozzle water comes out like a hose but no pressure


If you no longer have High Pressure coming out while machine is running, it's a pump issue. ... Campbell Hausfeld PW2575 Pressure Washer

I have a Honda xr2600 power washer. When I tried using it, water was squirting from the top of the gun. I took it apart to find that there are o-rings on top of some kind of washer---looks like a lock washer but it's made of cardboard??? Two of these washers were broken. I can get the o-rings but I can't seem to find the washers. I tried getting the manual for this model on line with no luck. Any assistance will be greatly appreciated.


The washers that you describe are made of teflon and are split to facilitate installation and/or allow expansion as they wear. These washers are actually seals and at times are used together with orings to seal high pressure. You should ... Honda Pressure Washers

NO PSI brand new north star 1573021c elec psi washer. no psi out of the box,, using correct nozzle, motor runs, good incoming water psi and volume. ??????????


Have you checked to make sure that keyway is installed between electric motor and pump. also adjustment on unloader valve may be incorrect. If the big brass nut on the unloader is able to be turned by hand, then this is probably your problem (running ... Northstar Pressure Washer 3000 PSI

Power washer the original clean machine 2400 psi low water pressure


... Comet Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2105 seconds