Having problems with your Pressure Washers ?

Ineed to replace the hose on my champion cpw1750 pressure washer but how do I disconnect from the gun or do I have to replace the gun as well


Answers :

If the hose is screwed into the gun then you are lucky because you only have to replace the hose, but if the hose is clamped inside of the hose then you have to replace both the hose and the gun
Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Ineed to replace the hose on my champion cpw1750 pressure washer but how do I disconnect from the gun or do I have to replace the gun as well


If the hose is screwed into the gun then you are lucky because you only have to replace the hose, but if the hose is clamped inside of the hose then you have to replace both the hose and the gun ... Pressure Washers

Pressure gun will not work, you have to disconnect the pressure hose, reconnect it, then it will work as long as you do not release the handle, if you do, you have to start that whole disconnect, reconnect process over again. It wastes time and we will not even mention the aggravation! What do we need to do?


Find a service centre or Local pressure washer co. Get the gun serviced ... Karcher K 2.25 R Electric Pressure Washer

Karcher 6.85 replaced seals as they were worn out and passing water into the oil now when I turn it on motor runs turning water on water comes out of outlet (which is ok??) but does not pressurize with hose disconnected. My Bosch pressure cleaner passes water through but when pump is started it pressurizes. Is it bypassing? Thanks in advanced


... Pressure Washers

No water I have a sears pressure washer. I hooked up the garden hose and pulled the triger with the engine off. No water. I disconnected the spray gun hose, were it connects to the pump.Turned on the hose,no water.Could the pump be cloged?


... Pressure Washers

Campbell Hausfield Pressure washer model 1549. After a few years of storage, I cannot prevent the powerful spray leaking from the connection between the Gun and the Lance. I replaced the O-Ring, and tried other means unsuccessfully. Spray from the joint is almost as powerful as spray from the lance nozzle. The Briggs and Stratton engine has been cleaned and operates well. The pump operates well. But the lance connection refuses to seal.


Hello,Most likely, the housing has split and seal is not being made. There is a chance that the hose is leaking where the fitting is crimped on (my experience, but different pressure washer). Are you able to see a leak when turned off b ... Campbell Hausfeld Pressure Washers

Replacement gun and hose for simoniz cl 11 - Omega Simoniz 1300 Psi Pressure Washer


... Omega Simoniz 1300 Psi Pressure Washer

Replacing the hose on a sealed gun karcher 330 pressure vwasher


... Karcher 330 Pressure Washers

I have a hobby 100-1 and the lance is now non effective.The water hoses from the gun quite well but once the lance is attached then no pressure and effectively is a trickle but on occasion it will tend to "spit".Sorry if my description is not very techy but it seems as though the lance has a blockage.Any ideas out there of how to Fix.


... Pressure Washers

How to disconnect pressure hose from hose reel .


... Pressure Washers

Hose (High Pressure) (not inlet or outlet hoses)coming from inside the pressure washer has a hole in it. Needs replaced. Is this a part than can be easily replaced or does a new hose need to be made?


... Honda Black Max 3000 Psi Pressure Washer

I have a Husky pressure washer with a Honda 2600psi engine. Problem is, no water will come from the pressure hose. I connected the water w/out the pressure hose and water flows thru strongly. I then connected the pressure hose w/out the wand and water flowed thru the hose fine. When I connect the wand and pull the trigger, nothing. I have replaced the wand and that was not the problem. Please help.


Check the quick disconnect to the wand these are spring operated and can get stuck ... Pressure Washers

I have a honda 2600 pressure washer. After running fine for a couple of seconds the water will stop flowing out the tip. It is receiving water,but will not flow it to the pressure hose. I even disconnected the pressure hose and no wate was flowing out. When I shut the pressure washer off it would then flow water to the hose again. Please help


This is a symptom caused by a sticking Unloader valve. The Unloader valve is inside the pump outlet body under the large black knob. \015\012Example picture : ... Honda Black Max 2600 PSI Pressure Washer

Why cant i get h2o to come out of my honda pressure washer? i disconnected hose, and no flow..was just workin fine other day


... Troy-Bilt 020528 Gas Pressure Washer

I have a Generac pressure washer, model #01450-0, with a Honda 5hp motor. The motor runs fine, but the pressure hose pulsates as if the pump is intermittently making pressure, and the pressure out of the sprayer is about half of what it should be. A friend suggested replacing the seals in the unloader. I bought an unloader kit, replaced everything and it still runs the same. It will build a small amount of pressure, spray for a few seconds, then the pressure dropps to almost nothing. Any help ap


Take a small diameter wire and poke thru the discharge hole of the spray head to clean out.\015\012Second time in 6 months that I had the same problem. The problem is alway in the spray head. ... Pressure Washers

Water sprays out of the the inlet for pressure hose quick disconnect fittin


... Dewalt 3800 PSI Pressure Washer

Troy Bilt pressure washer model 020209 will not build pressure-have checked all screens and intake in pressure hose and garden hose from house to pump. water leaks at gun handle- took it apart and oiled piston- was ''grabby'' but now snappy but still leaks. Engine starts fine and runs fine. Please help.


A leaking gun will kill all the pressure. You may need to repair or replace the gun ... Briggs & Stratton Pressure Washers

I have a Comet BXD 2525 G pressure washer pump which is giving me some problem. (Maybe) I hook the water up to pump and the pressure hose up to the pump, turn on the water and the water sprays out of the water connection at the pump. I check the hose to see if it was clog ok and the next was a the water connection ok. It's like the water is not going int the pump. When i start the pressure up the water come out of gun but no pump running like it should. The next thing i was going to look at i


The water inlet needs a gasket like all hose connections. If its gone the pump may be starving for water. ... Comet Pressure Washers

Husky HU80722 model Water flows thru the washer. Have disconnected all hoses, checked filter screen it is clear. Reconnected hoses, Engine runs fine home water pressure fows through washer. Still not producing any pressure.


... Northstar Pressure Washer 3000 PSI

Split Hose I have an Aussie Eco Clean H120 pressure cleaner and the pressure hose has split. can anyone tell me where I can get a replacement. Thank you.


I believe this link will take you to contact info for ordering parts directly.\015\012\015\012www.aussiepumps.com.au ... Pressure Washers

Hi, I have a Karcher 3.75 jubilee powerwasher, there is water coming out from where the high pressure hose connects to the machine and the unit pulses when idling but works perfectly without drop in water pressure, when trigger on gun is pulled, on closer examination the metal connection on the hose turns, is this the problem or something else. thank you.


... Karcher Pressure Washers

My Durabuilt power washer model #D81404 blew apart where the hose connects to the gun. I think I just need the copper fitting that connects the gun to pressure hose. Can you help me?


... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

I have a Karcher 550M pressure washer and was using today when all of a sudden the water started to pour through the handle hence lost the pressure of the water. Is this a rubber washer issue or the gun needs replacing or simpler than that. To be honest although I have had the washer for about 3/4 years now It is hardly used. Also can I fix it and where would I purchase the allen key to replace. Thanks Brian


... Karcher Pressure Washer Gun 91120200 91120200

Frigidaire built in dishwasher model PLD2855RFC1. Have to wash dishes pretty much spotless prior to using dishwaser. Glasses come out with what appears to be soap residue regardless if powder or liquid. Did not use a gauge but water pressure in rest of house is good, recently replaced water heater, pressure regulator and just replaced the dish washer water source valve. Washer is about 18 months old, has never worked really well.


Hi, \012\012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms online and ins ... Frigidaire PLD2855RFC Dishwasher

I have a Karcher 330 electric power washer. When connected and set to highest pressure (on variable wand) I get no motor action unless I reduce wand setting, then I get a little boost but not much. If I use high pressure conical wand I get high pressure sometimes, other times motor does not go and no pressure is delivered. I have replaced the high pressure hose.


Just wondering. have you tried it without an attachment to see what kind of pressure you get ... Karcher K2.26 Electric Power Washer

North star petrol pressure washer. working fine, then no high pressure, checked water feed, water filter , pressure relief valve and gun nosall well work sometimes and keep working, when you release the trigger and try in again the pressure gone again. please help, many thanks, richard


Sounds like the regulator is sticking or is airbound. loosen the water connection and then tighten it back. Could also be that the trigger gun is faulty or needs adjustment. Hope this helped ... Karcher 2500 PSI Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1173 seconds