Having problems with your Pressure Washers ?

Gun leaks wash then starts up

\015 First time to use it\015

Answers :

Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Why will water not flow through hose into the spray gun with the washer not started as well I started the power washer and the water still does not come out.


... Craftsman 2500 PSI Briggs & Stratton Powered Pressure Washer

HAVING LEFT MY KARCHER B602 OUT OVER WINTER ,IT STARTED BUT LEAKS FROM INSIDE THE CASEING. TOOK CASE OFF AND FOUND PLASTIC PIPE HAD COME OFF PUT THIS BACK ON STARTED MACHINE AND PIPE CAME STRAIGHT OFF. WATER WILL FILL SOAP BOTTLE IF PIPE IS HELD ON WITH WIRE, BUT STILL NOT MUCH PRESSURE FROM GUN. ACN YOU HELP WITH THIS PROBLEM.


... Karcher Pressure Washers

Unit Runs fine, except when you press the spay gun the engine stalls out. Unit was working fine, ran out of gas, filled tank and started engine. Engine was running fine, triggered spray gun and the engine stalls out.


... Pressure Washers

Power washer starts no problem but when turned on and activating the trigger on the pressure washer gun, water no longer comes out. The gun itself was replaced not long ago. What could be the cause?


The tip could be plugged up ... Honda Pressure Washers

The engine starts just fine. Everything goes okay until I pull the trigger on the spray gun and then the engine stalls out within 2-3 seconds after the water starts coming out. It is a 2700 Briggs and Stratton engine.


One thing I have found about pressure washers...you need to run water through the hose and everything until you get all the air out...or they will bog down and such until the air is out. ... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

Water wont come out of gun of power washer before starting it


... Briggs & Stratton Vox Professional 2500 PSI (Gas/Cold Water) Pressure Washer w/ Honda GX

Gun leaks wash then starts up


... Pressure Washers

Nilfisk Alto Active Waterblaster.Starts up good. When I release trigger on gun it does not start pressure again. I have to take water hose off


... Pressure Washers

My briggs and stratton pressure washer model 020206 starts and runs good but no water pressure coming out of gun...any solutions?


... Pressure Washers

I have a 5HP Honda engine installed on a Excell pressure washer. While the engine readily starts, it will not continue to run unless I keep the choke setting nearly completely closed. When I activate the pressure gun, it seems to generate adequate pressure, however, when the trigger is released, the engine continues to run at the same rpm instead of the normal variable rpm that most engines operate at during idling periods. The engine will always cease running when I push the choke rod all the w


... Honda Pressure Washers

I have a Karcher 550M pressure washer and was using today when all of a sudden the water started to pour through the handle hence lost the pressure of the water. Is this a rubber washer issue or the gun needs replacing or simpler than that. To be honest although I have had the washer for about 3/4 years now It is hardly used. Also can I fix it and where would I purchase the allen key to replace. Thanks Brian


... Karcher Pressure Washer Gun 91120200 91120200

Hy; I have a karcher 580 I had to replace gun complete so I bough a simoniz xe01-001 at simoniz.osirus.ca/ for your info 69$ complete ***.I install NOW I get pulse up & down ONLY when trigger is press I turn valve down i only get 10% of pressure if i turn valve up that is when it start pulsing pressure up & down it wont keep pressure up ... Bob...


Most likely problem is that the tip is too small causing Unloader to bypass or restriction/debris in tip. Install clean tip of proper size or 1/2 size larger (example from 2.5 gpm to 3 gpm ) to prevent slow pulse. If tip is clean and /o ... Karcher 2500 PSI Pressure Washer

The engine will start but I'm not getting enough pressure when I press the the sprayer gun. Water is coming out but no pressure. Not sure what to do.


This can be caused by three different components. Either your unloader valve has failed, your valves have stuck open in the head of the pump or your water seals are worn. If you get an initial jolt of pressure when you squeeze the trigger then we kno ... Karcher 2500 PSI Pressure Washer

It takes some time for the pressure to build up in the discharge gun and seems to take longer each time after I release the trigger and then start to spray again


... Pressure Washers

I have a McCulloch H.P. power jet cleaner 1300 and when i switch the device on the motor starts running but the pressure is not building up so no water is coming out of the pressure washer gun. We bought the device in 1999. Or alternatively is there anywhere in the UK to get the repairs carried out? Many thanks Michele.


... McCulloch Pressure Washers

The O-ring behind the quick connect for the hose to the gun leaks. I replaced this oring and the leak stopped for about 30 minutes then started again. Do i need to replace all the orings in the unloader valve?


... Pressure Washers

I have a Comet BXD 2525 G pressure washer pump which is giving me some problem. (Maybe) I hook the water up to pump and the pressure hose up to the pump, turn on the water and the water sprays out of the water connection at the pump. I check the hose to see if it was clog ok and the next was a the water connection ok. It's like the water is not going int the pump. When i start the pressure up the water come out of gun but no pump running like it should. The next thing i was going to look at i


The water inlet needs a gasket like all hose connections. If its gone the pump may be starving for water. ... Comet Pressure Washers

Troy Bilt pressure washer model 020209 will not build pressure-have checked all screens and intake in pressure hose and garden hose from house to pump. water leaks at gun handle- took it apart and oiled piston- was ''grabby'' but now snappy but still leaks. Engine starts fine and runs fine. Please help.


A leaking gun will kill all the pressure. You may need to repair or replace the gun ... Briggs & Stratton Pressure Washers

Pressure gun will not work, you have to disconnect the pressure hose, reconnect it, then it will work as long as you do not release the handle, if you do, you have to start that whole disconnect, reconnect process over again. It wastes time and we will not even mention the aggravation! What do we need to do?


Find a service centre or Local pressure washer co. Get the gun serviced ... Karcher K 2.25 R Electric Pressure Washer

Hi k2 series have alot of trouble does not always start on full pressure pull the trigger it just squirts a stright line of water out of the gun takes a while to get on full pressure if at all. many thanks stu


HI This is caused either by a partially blocked nozzle on the end of your lance or the unloader valve sticking inside the machine. You can clean your nozzle by inserting a pin etc inside the end to clean it out. If this doesn,t work then it is most l ... Karcher K2.26 Electric Power Washer

I can get the motor to start but it idles rough and does not get to full throttle before shutting itself off. Also very little water pressure coming out of gun at highest throttle speed when it does run very briefly.


You need to probibly just clean out the carb. ... Pressure Washers

Unable to start gas engine on a NorthStar pressure washer


Disassemble and clean the carb. If it ran briefly with the starer fluid then gasoline is not coming through the carb. ... Northstar Pressure Washers

New Troy-Bilt 3000 psi - Very Hard to Hot Start


When you run the unit and shut if off, release the pressure from the spray wand before trying to restart the engine. This built up pressure will cause it to be very hard to start as you have found out. If it does not start on the second pull release ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

My Husky Pressure Washer bogs the motor down immediately upon start.


Rebuilding the pump is not easy. Did you use the right seal drivers? Lube the seals when you installed them? Use a torque wrench? But a valve in backwards? ... Pressure Washers

Karcher pistol gun has broken


Make sure you DO NOT have a check valve (this is what stops your hose running when you disconnect from the hozelock fitting) in your hose pipe system, This will send a shockwave through the pressure washer and destroy the fitting you mentioned. They ... Karcher PSI Electric Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0566 seconds