Having problems with your Pressure Washers ?

The pressure washer 100 Bar PW1300/1400 WATERGUN IS LEAKING/BROKEN AND WANT TO REPLACE IT


Answers :

Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The pressure washer 100 Bar PW1300/1400 WATERGUN IS LEAKING/BROKEN AND WANT TO REPLACE IT


... Pressure Washers

I have a sears pressure washer, model 580752300. The pump on the underside vibrated lose and broke a couple screws. It came off and the oil drained out. I replaced the screws and it's ready to go except I can't find out how much replacement oil to put back in. Sears has larger containers but won't tell you how much oil to put in. However, there's a pricey pre-measured container they want to make you buy. Anybody know how much oil goes in that pump?


... FAIP Non Marking Pressure Washer Hose 4000 Psi, 50ft. Length

I left my electric karcher pressure washer it in the shed during the winter and they tell me that the housing and the safety valve need replacing. Can I repair it myself? They want 180.00 to fix it which is the price of the washer. Thanks


This needs new piston housing cover the existing one will have a crack in it. ... Karcher PSI Electric Pressure Washer

We want to replace the pump to our DEWALT DP3750 pressure washer and can not ge tthe pump to come off the engine. how do you get it to come off?


... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

I am looking for the replacement procedure for the stator drive belt for a Mi-T-M HSP-2403-3MGH pressure washer. I am at the point of separating/removing the housing that covers the crank pulley, and I'm having a hard time separating and don't want to pry or tweek things a bit too hard.


... Mi T M WP-3000-4MHB Pressure Washer

I have a McCULLOCH 1500 psi pressure washer and it seems like I need the top part of therod where the waer comes out it no longer adjusts the water stream seems like a little plastic defkector that you adjust your stream with, snapped and broke looks like I HAVE TO REPLACE THE ENTIRE TOP PART OF THE 2 PIECE ROD on the bar it says the following max130barmax60C PA66-GF30 Where could I purchase this piece Andy Nowostawsky my adress is 15447-rue d'esterel Pierrefonds,Quebec H9H 1Y9


... McCulloch Pressure Washers

I have a Karcher 550M pressure washer and was using today when all of a sudden the water started to pour through the handle hence lost the pressure of the water. Is this a rubber washer issue or the gun needs replacing or simpler than that. To be honest although I have had the washer for about 3/4 years now It is hardly used. Also can I fix it and where would I purchase the allen key to replace. Thanks Brian


... Karcher Pressure Washer Gun 91120200 91120200

Craftsman Pressure Washer Model #how do I adjust the unloader on my craftsman model 580752810 pressure washer, Just replaced it and it has considerably lower pressure than before.


... Pressure Washers

Frigidaire built in dishwasher model PLD2855RFC1. Have to wash dishes pretty much spotless prior to using dishwaser. Glasses come out with what appears to be soap residue regardless if powder or liquid. Did not use a gauge but water pressure in rest of house is good, recently replaced water heater, pressure regulator and just replaced the dish washer water source valve. Washer is about 18 months old, has never worked really well.


Hi, \012\012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms online and ins ... Frigidaire PLD2855RFC Dishwasher

I have a Generac pressure washer, model #01450-0, with a Honda 5hp motor. The motor runs fine, but the pressure hose pulsates as if the pump is intermittently making pressure, and the pressure out of the sprayer is about half of what it should be. A friend suggested replacing the seals in the unloader. I bought an unloader kit, replaced everything and it still runs the same. It will build a small amount of pressure, spray for a few seconds, then the pressure dropps to almost nothing. Any help ap


Take a small diameter wire and poke thru the discharge hole of the spray head to clean out.\015\012Second time in 6 months that I had the same problem. The problem is alway in the spray head. ... Pressure Washers

Hi, I have a Dewalt pressure washer 3100 psi. I want to know why the pressure washer works okay for 1 hour then it stop working completely. the oil is fine, the spark plugs are okay, and when I tried to start it again it does not work. Can you please tell me what could be the problem? This pressure washer is almost brand new I have used it for only like 30 hours for 2 years that I have it. I used it couple times lately but same problem it works for 1 hour then it does not work any. I will


There are two common issues that will cause what you are describing. What you need to do is run the machine until it dies as you are describing. Then pull the spark plug and check for spark. If you do not have spark you have a failing stater. It is v ... Dewalt DPH3100 Gas Pressure Washer

I recently purchased a northstar 4000 psi pressure washer. I had the same series pressure washer for the past 6 years and used a downstream chemical unloader quick connect to pull chemical. I attached it to the pressure washer and it is not pulling. I havent modified anything and I dont want to pull chemical through my machine.


The injector might be worn out or have something inside of the valve causing it not to ****. If you are using a new high pressure hose or a longer hose this may also have an effect over the injector not working. ... Northstar Professional Series Pressure Washer 4000 PSI

Replace pump on a darcher k2400 hh pressure washer


There is a bolt item 8 below on the very end of the drive shaft that has to be removed before you can remove the pump assembly. \015\012\015\012See page 16 item 8 of this ... Karcher 2500 PSI Pressure Washer

I want to remove the 4gpm pump on my pressure washer.


HI, It sounds like it is just stuck on the keyway as these can be very tight. You need to force the pump of evenly on either side and should come of if patient. ... Honda Maxus Prosumer MX5223 Pressure Washer

DeVilbiss/Excell XR2600 unloader acting up(low pressure) I removed the onloader cleaned and replaced now it loads up too much, engine wants to die but still has low pressure after initial burst?


... Pressure Washers

Wgvb2122 pressure washer builds pressure until you pull trigger, then no pressure. Replaced seal kit on plungers, same thing! Replaced unloaded assembly, same thing! Every thing seems to be as it should be and clean. Any ideas before I shoot this machine?


... Pressure Washers

Homelite 105 bar pressure washer - Homelite Pressure Washers


... Homelite Pressure Washers

Hose (High Pressure) (not inlet or outlet hoses)coming from inside the pressure washer has a hole in it. Needs replaced. Is this a part than can be easily replaced or does a new hose need to be made?


... Honda Black Max 3000 Psi Pressure Washer

I have a karcher pressure washer 1800 psi i bought from walmart it was running good until i had a power surge with the plug in. what can i do can i change the fuse in the plug or do i have to open the pressure washer up and replace a fuse.... thanks


You will have to take the cover off & look for melted wires or a fuse.\015\012if there is no fuse the capacitor may have been cooked.\015\012it should be a white cylinder.if it has been damaged it will have burn marks and may be swollen. ... Karcher PSI Electric Pressure Washer

Karcher pressure washer My Karcher pressure washer switches ON and OFF continually when I am trying to wash. It is about 6 yrs old 120 Bar 1750 PSI 420MH


... Karcher 2500 PSI Pressure Washer

Calgary, AB - McCulloch Pressure Washer FH180B casing is cracked, where can I find the parts and how much to replace it, or should I purchse a new pressure washer.


... McCulloch FH180A Electric Pressure Washer

Kew hobby 1650 pressure washer pressure switch replacement


... Pressure Washers

Wickes 160 bar pressure washer - no pressure but motor working


... Pressure Washers

I have a Karcher 330 electric power washer. When connected and set to highest pressure (on variable wand) I get no motor action unless I reduce wand setting, then I get a little boost but not much. If I use high pressure conical wand I get high pressure sometimes, other times motor does not go and no pressure is delivered. I have replaced the high pressure hose.


Just wondering. have you tried it without an attachment to see what kind of pressure you get ... Karcher K2.26 Electric Power Washer

I have a Husky pressure washer with a Honda 2600psi engine. Problem is, no water will come from the pressure hose. I connected the water w/out the pressure hose and water flows thru strongly. I then connected the pressure hose w/out the wand and water flowed thru the hose fine. When I connect the wand and pull the trigger, nothing. I have replaced the wand and that was not the problem. Please help.


Check the quick disconnect to the wand these are spring operated and can get stuck ... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0859 seconds