Having problems with your Pressure Washers ?

The O-ring behind the quick connect for the hose to the gun leaks. I replaced this oring and the leak stopped for about 30 minutes then started again. Do i need to replace all the orings in the unloader valve?


Answers :

Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The O-ring behind the quick connect for the hose to the gun leaks. I replaced this oring and the leak stopped for about 30 minutes then started again. Do i need to replace all the orings in the unloader valve?


... Pressure Washers

Unloader valve Thanks for the insight on my problem with a Karcher 550m. I have taken the pump motor out of the unit. How do I identify the unloader valve & replace it? There does not appear to be any other leaks. Is this the only part that needs replacing if pressure is down? Many thanks


... Pressure Washers

Our GE dishwasher (5 yrs old, Model GLD4250L00CS) only fills with water half way when the unit is started. The inlet valve was replaced with a new one, but that did not solve the problem. When started, the dishwasher fill cycle runs for 41 seconds before the wash cycle begins. Repair workers told us we probably need a new ECU (Electronic Computer Unit). My questions are: Is 41 seconds the correct time for the fill cycle for our model? What else could be the reason for the unit not filling pr


Hello &\015\012Welcome to FixYa\015\012\015\012Check this\015\012 ... Dishwashers

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started. I have the same problem. Water flows thru the pump when not running, but no flow or goes in by-pass mode when I start the pump. The pump being Troy Bilt Model 020296-01. I replaced unloader valve even. Anything else I can do?


You replaced the unloaded valve. Are you positive you have the unloader screwed to pressure and not turned the opposite way? You will have no pressure if it is adjusted wrong. One other thing I have encountered is that the unloader has a ball bearing ... Pressure Washers

RY80940 The valve under the pump is leaking. I think it is a pressure release valve but I am not sure. I tightened it when I had to re attach two bolts that were holding the motor on the metal case then it worked for awhile then it started to leak and I lost all power. Should I tighten or loosen it or is there a washer that needs to be replaced?


... Pressure Washers

Hello, I had a problem with my Bosch dishwasher not washing properly. I have fixed burnt out wires, replaced the water inlet valve, AND tested with a new control module. Nothing is helping. When I start the cycle, it completes the initial drain and water does flow into the unit for about a minute, maybe a minute and a half. I can hear the clicking of cycle changes but it is not washing. Eventually it will drain the inch or so of water in the bottom, but it never washes. Any help???


Hi,\015\012\015\012Welcome to Fixya.\015\012\015\012Can you hear the wash motor humming ? I`ve got a "pdf" I can send you regarding this if you want to contact me at ... Bosch SHU9925UC Built-in Dishwasher

Unable to start dishwasher, only functioning light on the panel is the cancel/drain light. push that button the machine funtions for a minute or two and shuts off,also the light above normal wash is blinking. When the machine last functioned it would start with a very high decibel level.If its the circuit board I need an approximate replacement cost. Bob


If you go to searspartsdirect.com you can get the exact cost of the module. ... Dishwashers

CMA-180 Dishmachine-4 years old, used up to a maximum of 5 times a month. After 10-12 loads it shuts down, alto the lights are on, it won't start for about 30 minutes. Is it possible there is a heating element in the machine that needs replacement, or our water heater is not keeping up?


... Cma Dishmachines CMA 180 Free-Standing Dishwasher

Maytag Quiet Series 300 Dishwasher - MDB96000AWQ - Panel flashes '9' from time to time. Sometimes you're unable to start it. Did ewset the unit (powered off for 15 minutes and also for 1 week). What needs to be fixed / replaced if anything. Thank you in advance.


... Maytag MDB9600A Jetclean II Built-in Dishwasher

My panasonic range microwave NN-S255WF started to randomly beeping and flashing the potato/vegetable setting. For about 15 minutes the microwave keypad would not work at all. It is working again. The range overhead light on the bottom of the unit stopped working about a year ago - light will not turn on. Please tell me what the issue is, what would need to be replaced. The microwave is 4 years old. Thank you!!


We get microwaves in our shop frequently, this unit sounds as if it's brain has been damaged, I suspect, as it usually is that either the magnetron, or the High power Diode, has failed, this usually also, "Spikes" the "Brain" as well. At 4 years old ... Dishwashers

FDW70 dishwasher, starts to fill with water, shows pre wash on control panel, then pumps out within about 2-3 minutes, but has vertualy no water in it. Puts up code A10 on control panel, can still hear the pump going even when l open the door. Have replaced a burnt out heater tube with a new genuine unit, also have removed & checked fill valve & this works fine.


Hi,Try this few steps;Turn off the water supply to the dishwasher and remove the hose, turn\015\012on the machine for a couple of minutes in a fill position then turn off\015\012the machine, reconnect the hose, turn the ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Unloader valve broke off and in need of replacement


Http://www.mastertoolrepair.com/images/020338_0PUMP.pdf ... Honda Black Max 2600 PSI Pressure Washer

So I found this power washer for sale. The seller claims that the washer generates a good stream of water, not just full power. He also mentions that after a few minutes the engine starts to bog down like it is working extra hard. Does this sound like a pump issue? Could something be clogged or would the pump need to be replaced? Or should I avoid this power washer?


Don't buy a power that doesn't work.There are many expensive parts on a power washer. If it was cheap and simple to fix, the seller would fix it and the washer would not be for sale.Would you buy a car that doesn't work? Especially ... Pressure Washers

Bosch dishwasher (SXH55MO6UC/46): The power comes on and runs normal, but no water is coming into the unit. I was told that it was a water inlet valve that needs to be replaced (part #263833). I need to know if this is what needs to be replaced and if so, is this something that I can do or do I need an expert repair service to do it? If it is something that I can do, I need instructions. I am handy, but this is something that I have not done before, Thank you, Craig Covey


Hi Craig,Yes it may be the fill valve...but first take off the pipe or hose and check the screen just inside the fill valve...some do not have it but most do...also check that water comes out of the hose or pipe at the valve....THEN ... Bosch Integra® 500 SHX55M05UC Built-in Dishwasher

CLEAN OR REPLACE UNLOADER VALVE


... Karcher Pressure Washers

Whirlpool - Quit Partner I - DU1048XTP: Start at the beginning - Dishwasher would go through most of it's wash cycle and stop and the 'Start/Resume' LED would start flashing. Would press 'Start/Resume' and wash cycle would start again and run non-stop. Would have to hit 'Cancel/Drain' to stop. Called local service tech and he said board would need to be replaced. First board he brought failed right away, second board was installed. Tech also replaced latch handle assembly because it was missing


Have you asked the technician if the water temperature is OK.\015\012\015\012Run it again and after 30 minutes cancel and see if water temperature is warm or not. If not warm enough, then likely causes are heater is faulty or if you are u ... Whirlpool Dishwashers

Hello I have a Maytag Quiet Series 300 dishwasher model #MDBH955AWW that is making a lot of noise. I saw an exchange on this site where the expert suggested filling the washer to just above the heating element, running it, and seeing if that solved the problem. I tried that and it solved the problem. I believe the expert said this indicates the fill valve needs to be replaced. Can you tell me which valve I need and advise me on how to change the valve? The manuals I have (Use & Care Guide and In


Http://sites.google.com/site/cwyffimsbffoe/maytag-dishwasher-parts-manual- ... Maytag Dishwashers

I replaced the control board but the washer still will not start. Does the start bottom on the front need replacement?


Replaced the front control panel ... Maytag 24 in. MDB7601AWS Stainless Steel Built-in Dishwasher

I have a 4,000 psi, 4.5 gpm 45G cat pump powered by a 13 hp honda engine I can not seem to be able to adjust the unloader valve to give me pressure over 950 psi and even at lower pressures, the pump will not deliver consistant pressure without bouncing off to the relief stage and back into the tank Are unloader valves worth repairing, or should i look at just buying a new one my current thought is to buy an EZ start Pulsar


I would just purchase a new unloader valve, they usually aren't worth rebuilding. I would like to have a picture of the set up that you have, if you can send me a picture of the unloader region of the pump I can get you are price on a new one. email ... Honda Pressure Washer PSI 3000

I have the dishwasher model number FGHD2433KF, I have noticed in the last few that I have used my dishwasher no matter what setting I push after a few minutes it jumps to 99+.... Example a push quickwash and start it, the time that shows on the screen is 50, it counts down to 49 then it jumps to 99+. Every setting I originally set starts out at the right time that is listed in my book but then after a few minutes it jumps to 99+. Do I need to call service. I purchased the dishwasher in May of


... Frigidaire FGHD2433K 24 in Builtin Dishwasher

It won't start. It has to be in the handle. What needs to be replaced or repaired? I know its getting electricity. Is there are relay switch that might need replacing. I know it is in the handle area.


Their is a lever switch, that can fail, please rate/vote this response ... Maytag 24 in. MDB3700 Built-in Dishwasher

The start switch (right side) not power switch (left side) broke....(below the overlay). I need to replace the switch and overlay. What part(s) do I need to fix the switch. I now have overlay part number. This is for "start" switch... Thanks


Hello again,\015\012\015\012I'm glad I was able to help you earlier with the overlay, unfortunately I'm not sure I can go 2 for 2 because the start switch issue is going to be a little more involved.\015\012\015\0 ... Asko 24 in. 1805 Built-in Dishwasher

Hi I have a Kudso1flSS1 dishwasher. I just replaced the control board and the switch board assembly, the pump is recently replaced and the filter is clean. The start button keeps flashing and the water level is always low. The DW stops running after 15 minutes and the flashing starts again...... Help!


... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

I have a HD 2701 DR pressure washer that starts and runs fine and usually works fine the "first" time but if you let go of the trigger and then try to use it again you just get a trickle out of the end of the wand. Usually if you hold the thing open for a while it will kick in (sometimes it takes forever...). Any ideas? It sounds like some of the "unloader valve" problems are similar but I do not see an "unloader valve" in the parts lists for the 2701...


... Karcher G 3050 OHR Gas Pressure Washer

I need to check the unloader valve on my Karcher 3000psi pressure washer. I was directed to your site for help. I just need to know what to unbolt to get to the valve.


... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1569 seconds