Having problems with your Pressure Washers ?

Engine will not start when the water is on. You can start the engine and then turn the water on but it will kill the engine. I have tried to clean the unloader valve.


Answers :

To isolate whether or not the unloader valve is still stuck or sticking, try starting the unit with the wan trigger engaged water coming out to spray. If the unit runs while wan trigger is engaged and shut down when released your unloader valve isn't working. Hope this helps God Bless
Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Engine will not start when the water is on. You can start the engine and then turn the water on but it will kill the engine. I have tried to clean the unloader valve.


To isolate whether or not the unloader valve is still stuck or sticking, try starting the unit with the wan trigger engaged water coming out to spray. If the unit runs while wan trigger is engaged and shut down when released your unloader valve isn't ... Pressure Washers

De Dietrich Dishwasher - DVH 610 JUI - when turned on to any programme and started automatically tries to drain water instead of filling with water. Was disconnected and filters checked and were clean. when turned on again it worked and when disconnected to be brought back into house it again tried to drain water instead of filling. All lights come on except blue light. Does not accept engineer code given with wiring leaflet


... Dishwashers

I have a Sears (Briggs) 2550 washer mod # 580.752190, has been working great but when I got it out last week it wouldn't start with the water on, I turn the water off bleed the pressure out the wand and it started and ran great, I thought it might be the relief valve, I removed the valve turned on the water, a big stream was shooting out the hole where the valve goes, I started the engine and it ran but sounded like it was about half loaded. where do I go from here ? Thanks.


... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

Inlet/Drain light is on. I have cleaned the drain pump and non-return valve, rinsed under water, removes all foriegn objects, turned the drain pump impeller (which turns freely) and carefully replaced the non-return valve and secured it with the locking clamp. I tried turning off the dishwasher and teuned it back on. No warning light shows but as soon as I try the dishwasher on a wash cycle it fails to pump water into the machine and release the washing tablet door. The programme unit makes a no


Is the water inlet turned off by chance? Is there no water at all inside the dishwasher? ... Miele 24 in. G643Vi Plus Built-In Dishwasher

Coleman power washer PW0912201. Water is blowing out of the chemical pickup tube when water hose is turned on prior to starting. After starting the water realy blows out from there. Would the unloader be faulty? I tried to pull out the unloader stem assembly from the manifold but it appears to be pressed in. Do I need a new manifold kit? or am I looking at the wrong part to correct this?


... Coleman Pressure Washers

I have an Indesit IDL 42 dishwasher. It has entered a state in which it behaves like this: as soon as I turn it on, it starts swishing the water around (it doesn't pump it out) and it does that regardless of whether I press any buttons (I have tried Start, Reset, turning the program knob, no difference at all). When I open it in the middle of this cycle, the water drips, and there is plenty of water (about 1 in) at the bottom. I have checked the filter, it is clean. Can you please help?


... Dishwashers

Hi, The machine will not complete a cycle. I think it may have started when the power was turned off at the mains during a cycle. Symptoms are : - You can turn machine on, select a program, press start button, close door, machine appears to begin cycle as normal, water seems to load, then 2 minutes later drains, and 1 minute or so after that the machine beeps 3 times to indicate cycle is finished. Dishwasher tablet door never opens, dishes not cleaned. Have tried : - cleaning filters; - turn


It is likely the dishwasher is locked in some diagnostic program.\015\012If you provide the dishwasher model no. then I can try to find out the keys you need to press to get it out from it. ... Whirlpool Dishwashers

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started. I have the same problem. Water flows thru the pump when not running, but no flow or goes in by-pass mode when I start the pump. The pump being Troy Bilt Model 020296-01. I replaced unloader valve even. Anything else I can do?


You replaced the unloaded valve. Are you positive you have the unloader screwed to pressure and not turned the opposite way? You will have no pressure if it is adjusted wrong. One other thing I have encountered is that the unloader has a ball bearing ... Pressure Washers

I have a Husky 2600 PSI power washer with the Honda GCV160 engine that I can't get to start. It was okay when I purchased it from Home Depot last spring but now I've tried putting new gas in it, spraying carb cleaner, new spark plug, and it still won't start. I only ran it for about 30 minutes when I first purchased it. The guy at the service desk at Home Depot told me that the water hose should be attached and turned on while trying to start. Is this true or would this be starting the motor und


You can eliminate the motor by unbolting the pump from it and then if it will start the problem is with the pump or the unloading valve.If it does not start with the pump removed then you check for spark and get the carb cleaned or have a kit put in ... Karcher 2500 PSI Pressure Washer

I have a 7 yr old Miele G 641 SC Plus dishwasher, the inlet/drain light comes on and stops the wash cycle.I have tried cleaning the water inlet filter, drain pump and non return valve many times, the wash cycle then starts with the pump out of existing water and can sometimes go for about 20mins( sometimes happens a soon as the water starts to flow in) into a cycle before stoppinig again with inlet/drain light on.


... Miele 24 in. Novotronic G851SC Plus Built-In Dishwasher

Engine starts easy. engine revs up and down but does not maintain a constant. Preasure tries to come up and then quits. the governor eeps moving back and forth. I have cleaned everything including the unloader. I used lithium grease on the o rings and still it does the same. Could this be caused by bad gas, even though it starts and runs very easy


Hi And welcome to FixYa. I am Kelly I doubt that it is caused by bad gas.-It can be caused by a dirty float bowl nut or a restricted orifice in the bottom of the carburetor venturi. - Also a broken or very worn governo ... Karcher 2500 PSI Pressure Washer

Cloudy Dishes My dishes have just recently started turning cloudy with white fllm. This has never happened before and the dishwasher is approximately two years old. There is no issues with hard water, and have used Jet Dry, have tried cleaning it with bleach and vinegar, and have used soap and no soap. Please give me suggestions as to why this would start occurring now. I took off the inside panel and it was full of all kinds of gunk which I since cleaned out. I would like to know how to avoid t


There is a new product out that filters the water going into your dishwasher. the film or cloudy white look is caused by hard water. this filter eliminates the problem and is very affordable. you can get it at dishwasherfilter.com. i was amazed how c ... Dishwashers

My dishwasher was recently 'installed'. i don't know if the contractor made a mistake or if the water valve is not turned on, but the cycle tries to start but then no water is flowing into the dishwasher. everything appears to be hooked up, but I think it's the water issue b/c i also have a new refrigerator and the water dispenser/ice maker does not work because no water is flowing into the fridge either.


This sure sounds like a water valve issue, for sure. You will have to trace out the lines (not easy, but possible) and figure out where the valve is. They usually turn left to open, and right to close. I would call the contractor and tell them ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Bosch SHE4AM16UC/01 tries to start a cycle but the clean light comes on after about one minute. I don't see any standing water in the tub and the screen for the fill valve appears to be clean. Any ideas?


... Bosch SHE4AM16UC 24 in. Built-in Dishwasher

We have a Blomberg dishwasher. We came to a finished cycle to find water in the bottom. We have removed the water by hand, cleaned the filter and the hose. The lights come on, but it doesn't respond when trying to run a cycle. It will do it's ''finished cycle beep sequence'' at the end of the cycle that it didn't actually run. We have reset it by holding down the start button. Turned it off and on, etc.


I am curious what the repair guy found. We have the same problem. ... Dishwashers

My Kenmore Elite suddenly stopped filling with water. I pushed start but when I checked it hours later the soap dispenser door had opened, the soap is just lying in a puddle, and nothing is clean but the clean light on the front panel is blinking. I tried again to no avail. Any ideas? I've had the machine since it first came on the market and have had other issues with it--it never drains completely, it makes sounds like someone revving a sports car engine when the drain pump is engaged, my dish


Https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a4 ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

We have a frigidare model PLD4375RFC3 dishwasher that won't turn on! I select the cycle and press on and it just shows me the time for 15 or 20 seconds and then turns off. I opened the bottom and everything looks ok, there are no leaks and all wire connections are in place. Latley the motor has been squeeling a bit and the dishes have not been clean so obviosley something has taken a dump! I just need to know were to start, is it the water valve or circulation pump and how do I test them?


... Frigidaire PLD4375RFC Dishwasher

Dishwasher does not start it seems there's no water coming in the tub. I got a trouble shooting manual from ejunkie.com and tested the coil of the water valve which read 1000 Ohms, which means it's OK. Then I hot wired the coil while connected to the water line and the valve opened and I had water flowing [ in a bucket] I have tried to start the test program [hold power scrub plus and regular switch at same time then start button] and lights start flashing you hear drain pump come in then the un


... Bosch SHV4803 Dishwasher

Unable to start gas engine on a NorthStar pressure washer


Disassemble and clean the carb. If it ran briefly with the starer fluid then gasoline is not coming through the carb. ... Northstar Pressure Washers

My G832SC is not draining at the end of the cycle. It runs the entire cycle, and the dishes appear to be clean. The soap dispenser has opened and the dishes are rinsed. However, the dry cycle doesn't run because the machine doesn't drain at the end. The intake/drain light is flashing. If I reset the machine and start a new cycle, it will perform an initial drain and the water level does go down. We checked the tri-filter and the valve pump thing, rinsed both. Checked the hose under the sink. We


... Miele Slimline G832SCi Built-in Dishwasher

Have three yr old Troybuilt pressure washer. Model 020276. Used 5 times. Engine starts up ok, but when pressing wand, it kills the motor. Also have hot water flowing from valve that I had not noticed before. HELP. LA moi.


... Honda Pressure Washers

Fisher & Paykel DW60. Fault: Will not start regardless of program selected. E.g. if "heavy duty" pressed, only light will flash, if "normal" is pressed, only this light will flash etc. All hoses (water and drain) have been checked and no crimps or blockages found at either end. All usual methods tried (e.g. cleaning strainers and filters, turning power off for a while etc). Finally, while lights are working, the machine makes no noise at all when a pogram is selected.


... Dishwashers

Poor pressure karcher g 2500 pressure washer with a 5.5 honda engine. No high pressure, hose pulsates as does water out of the outlet. have removed the unloader valve twice and cleaned it to no avail


I had this same problem on my pressure washer.the pump had some broken parts in it .i found my replacement pump on EBay. ... Karcher 2500 PSI Pressure Washer

We have a Karcher G2500VH pressure washer. If you start the engine with the trigger pulled on the spray wand it will run at full pressure until you release the trigger. after that, when you pull the trigger it will not have any more pressure than the water hose feeding it. Does it have an internal unloader valve? What is the part number?


Hi, Karcher calls the unloader valve a spill valve, this is a link to a full drawing/parts listing , and your fault description might well be a sticking /seized unloader(spill ) valve hope this helps ... Karcher 2500 PSI Pressure Washer

Honda engine turns 3/4 then locks up under pressure? Cant pull start. Tried without pull rope, and same thing? Is this a valve stuck? How much for repair?


... Honda Pressure Washer PSI 3000
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2010 seconds