Having problems with your Pressure Washers ?

The power washer is surging cuting in and out when i turn da nozzele to get stronger water pressure?


Answers :

When I use my machine I hook up the water to the pump, hook up the high pressure line and gun, then turn on the water full and squeeze the triger to make sure all air is out before starting the pressure washer(mine is gasoline powered). Then I install the nozel on the spray gun. If you are having surgeing water pressure Check the hose washer where the water hose hooks to the machine, and be sure the supply hose is not restricted and valve is on full.
\015\012If this was helpful please leave Feedback. Thanks, SP
Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The power washer is surging cuting in and out when i turn da nozzele to get stronger water pressure?


When I use my machine I hook up the water to the pump, hook up the high pressure line and gun, then turn on the water full and squeeze the triger to make sure all air is out before starting the pressure washer(mine is gasoline powered). Then I insta ... Pressure Washers

Using a Bosch 1600W Pressure washer Aquatak 110 plus Was adjusting the twist pressure sleeve to get HIGH pressure and water supply stopped and sleeve seems fixed/seized. I turned power ON and OFF and turned water tap ON and OFF but still no water coming out of the nozzle. What do I do now?


... Pressure Washers

I have a campbell hausfeld 2450 pressure washer with water coming out of a brass hose nozzel right next to where you screw the high pressure to the pump as soon as you turn the water on from the house, start it up and high pressure comes out of it and the hose about half pressure, any ideas?


This is called the chemical injector which enables you to insert the hose for you to dispense the soap and or chemical by utilizing a soap nozzle .apparently inside this barb you will find a ball a spring and a o-ring,find the replacement parts or ki ... Campbell Hausfeld Pressure Washers

I'm trying to get a Durabuilt pressure washer (model DB1303) to work. After hooking up the water hoses I plug it in and turn on the power. It sounds like it's running but there is no increase in pressure and it runs continuously. I only let it run for about 10 seconds and then turned it off. I tried it a couple of times...no luck.


... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

When I turn on the shop force 1750 electric power washer I get water pressure in intermittent time frames. For example, it may run for a second then stop for ten seconds, then start again for three seconds then stop for 3 seconds then start for a half a second then stop for five seconds etc. until ?. This type of pattern continues for at least ten minutes, which is when I give up. I have tried adjusting the the water hose pressure, high, low. middle, nothing changes. This happen when I have the


The usual cause of this is sticky Orings in the water admitance valve.\015\012\015\012Take the valve apart and clean the bore with crocus cloth wrapped around a rod and replace the Orings and lube with a bit of plumber's grease and reasse ... NIB Shop Force Universal Pressure Washer Accessoriesnib

Have whirlpool dishwasher model DU1055XTSS2 and the top rack water wheel does not spin. Operated the washer with door opened and it gets water but doesn't spin. There are no restrictions to the jets on wheel and the wheel turns feeely. The only thing i can figure is inadequate water pressure....


... Dishwashers

Hi I have a Nemo Dishwasher and the top spray arm is not turning. The bottom one is going fine and there is certainly plenty of water getting into the washer as I opened the door with the washer going and it flood me. I can see the water getting into both spray arms - the bottom one has a excellent upward spray and turns - the upper spray arm has water getting into it but it will not turn. I have cleaned the dishwasher out and any internal parts that I could find so it is spotless - this is so f


... Fisher and Paykel DS602 Dishwasher

My dishwasher top washer is not spinning....What causes it to turn (water pressure)? and if so does it recirculate the water...my inlet could be stopped up...dishes on top rack are not getting cleaned


Water is just circulated by a pump motor, Check to make sure it is getting enough water (just around the element) ... Whirlpool 24 in. DU1055XTP Built-in Dishwasher

Hello, I have a Craftsman Clean N Carry® 2150 psi Gas Pressure Washer w/4.0 hp Briggs and Stratton Engine. My problem is that I can't get any water to come out of the nozzel. What can I check to fix the problem? Also, where can I get a book to look at for parts and problems?


... Pressure Washers

My Snap-On 2000 PSI Electric Pressure Washer is not working. When I hook up the water hose and plug the power cord on and turn the machine on, all I get is a leak under the machine. Is there a shop


... Pressure Washers

Northstar Hot Water Pressure Washer (model #157322) While using the pressure washer the safety relief valve activated venting steam and hot water from it... I immediately shut it down and let it cool down. After it was cool, I turned on the water supply again and the relief valve was still spewing water from it. My neighbor said it was probably the "unloader" valve was stuck or damaged. I called around my area and it seems as though no one services my pressure washer.. Is there a manu


... Pressure Washers

Water not getting to the spray nozzel - Briggs & Stratton Pressure Washers


I suggest taking the nozzle off and see it if you get water, then the gun, then the hose ,etc until you see if the pump is actually working. This breaking it down will tell you if and where it is blocked or if there is another problem. Also a model ... Briggs & Stratton Pressure Washers

I have a Karcher model K 3.97M. When turned on the pressure surges an I only get a fine stream of water from the rotating wand.


... Pressure Washers

Pressure washer won't turn over with water turned on


... Karcher Pressure Washers

Briggs and Stratton Troy Bilt gas pressure washer one year old. I can get water thru pressure washer and bleed the air, water comes out the hose just fine until I start the pump. Then, I lose all water flow. Pump runs fine but when it's running, no water goes through.


... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

I have a Delonghi dishwasher, it's a stand alone, like a washing machine. The water inlet is connected to the hot water tap, normally used for a washing machine. When we first started using the dishwasher, we kept getting the E4 error message, we reduced the water inlet pressure by turning down the tap, that worked for a while. Just a while ago, we started getting the E4 error message again, not sure we can turn down the tap any further without cutting the water off completely. Do you have a


The E4 error message could be because the water pressure is too low rather than too high. Can you let me know the exact model number of your dishwasher and I should be able to tell you more.\015\012\015\012Regards,\015\012BElectric ... Dishwashers

I have a Comet BXD 2525 G pressure washer pump which is giving me some problem. (Maybe) I hook the water up to pump and the pressure hose up to the pump, turn on the water and the water sprays out of the water connection at the pump. I check the hose to see if it was clog ok and the next was a the water connection ok. It's like the water is not going int the pump. When i start the pressure up the water come out of gun but no pump running like it should. The next thing i was going to look at i


The water inlet needs a gasket like all hose connections. If its gone the pump may be starving for water. ... Comet Pressure Washers

I have a Karcher 3.99 Pressure Washer. The motor appears to be working and water is passing through the machine when turned to the detergent application setting. However when the lance is tightened to turn on the pressure, no water is coming through. The Karcher is just over 1 year old David


Hi I have a karcher 3.99 the motor comes on and water comes out however thre is no pressure i have tested the lance on my brothers washer and this is ok what is wrong ... Karcher K 5.85 M Electric Pressure Washer

I have an older Landa Pressure Washer. The burner is not working. Once I get the machine running and water flowing to the pressure washer, with the wand pressed, I flip the burner on switch....and nothing...I have no idea how to work on a pressure washer burner. I have been told it could be the igniter, but I don't know how to fix it if it is. Any help is appreciated.


Check for 12V at the igniter connector with the unit running. If you have 12V and no igniter it may be stuck or bad. Thrun the unit off and read continuity across the DISCONNECTED igniter plug / terminals to the igniter. No resistance = open ignit ... Pressure Washers

Turn water on then actuate wand trigger. Pressure washer leaks when wand trigger is actuated and has very low pressure/flow output. After releasing trigger the pressure cycles on - off at approx 1 second interval. I suspect that the plasstic oulet tube is leaking causing low pressure leak out of bottom when trigger is actuated and causes pressure switch to cycle when the trigger is released. Any Help? This pressure washer is approx 18 months old!


You gave a very close solution yourself for the problem. But other leakages can cause such symtoms.Forexample a leaking head or a leaking chemical inlet. These can be caused because the spill valve (pressure control valve) is stuck. When this valve s ... Karcher PSI Electric Pressure Washer

Champion dishwasher we have a champion freestanding dishwasher at my church. after the cycle is completed, the pressure guage behind the washer still shows 25-30 and it contnues to spray water. not forced by the motor, but more like a stuck open fill valve. if i turn off the water and run it, then turn the water back on, the valve is closed and does not let water freely in. butif i run it with the water on, it will continue to spray in freely after the cycle light goes out and you open the door.


If you turn the unit off from the circuit breaker will the water still run?if so the guts inside the solenoid valve are worn.you can call champion and get a kit to replace the worn parts and its not difficult to do.hope this helps. ... Dishwashers

We have a Model 587.1440*, 587.1441* Kenmore dishwasher. I had turned the water off to the whole house when we left for vacation and openned one faucet so the water pressure would be off the house while we were gone. Upon our return, I turned the water back on but the dishwasher gets no water. ?? What happened? It was working fine when we left, now no water. ?/


First, have you run it long enough to purge the air from the dishwasher line?\015\012\015\012Secondly, the solenoid valve for the water inlet may be stuck due to no pressure on it while you were gone. Tapping it with something light like ... Dishwashers

I have a Karcher K2.65 Deluxe pressure washer. All connected up, turned it on but I have low pressure out of any of the attachments and water splashing out of connection between gun and extension tube


... Pressure Washers

2-yr old troy-bilt pressure washer with honda gcv160 engine. seems to run well, but when trigger is pulled get full pressure for less than 5 seconds before reducing to house water pressure. when left running, looks a black plastic pressure relief valve starts blasting hot water. appreciate whatever insight you can give. Thx


It sounds like an air lock. Try this: With the machine off, connect the hose to the washer and let it run for several minutes to get all of the air out of the hose, and to purge any air out of the pump. Shut off the water, and connect the high pre ... Briggs & Stratton Pressure Washers

Frigidaire dishwasher (Electrolux FDB750RCB0) does not move water through the hose to the upper wash/spray bar. The lower wash/spray bar has pressure enough to turn. With the dish washer out from under the counter I can see the water rise very slowly up the translucent hose. If I remove the check ball under the stem assembly in the motor in the bottom of the tub, water flows, but I'm not sure if the top bar turns then (with the door open I see water coming down from the top, but never saw


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2072 seconds