Having problems with your Pressure Washers ?

Pump broken and leaking thru crack, looking for used pump for this model


Answers :

Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Pump broken and leaking thru crack, looking for used pump for this model


... Pressure Washers

Looking for info on our churches dishwasher - Toledo Kitchen Machines. Model # TDA27. I can describe it as a single cycle dishwasher. Wondering what type of detergent to use and if there is a manual available. There is a small seal leak between the motor and the pump, other than that everything works. ( this has not been used in 10+ years).I am now in charge of bldg maintenance and am trying to get everything in working order. Any help is appreciated. I am guessing the circa is mid to late 60's


Dishwasher Repair Guide: How To Fix a Dishwasher - ACME HOW TO.com\015\012\015\012\015\012\015\012 ... Dishwashers

Getting water i think in the engine of my 3000 psi northstar i bought last october and pump oil looks dark almost plum color now, not golden thru the site glass like it was earlier and it quit running model number is m1578112c.1 is it repairable? only used it 3 times


... Northstar Pressure Washer 3000 PSI

Water leaks from underneath the unit. Water only leaks when the pump cuts on (pressurizes). It leaks down on to the hose connecting to the water inlet valve on the right hand side of the unit when looking at the door of the unit. When the unit is full of water and the motor / pump is not running the unit does not leak. This unit is a Maytag jetclean dishwasher Model DWU9200BAB about 12 years old


Please change the 'o'rings of drain line and the inlet and also check the drain hose and the inlet if there are any holes in it ... Dishwashers

We have and older Jackson model 10 AB at church, used 10 to 20 times per year. The pump motor quit this summer and was replaced by a local appliance service company. About $700 job. Upon using it recently, the first time since the new pump was installed, the RINSE cycle seems very anemic, that is, low volume and low spin rate. The dishes were not completely rinsed. Temperature was correct, 185 degrees. The service person came back to look with no improvement and now the Heaters will not co


Sounds like a wiring problem but it is controled by a thermo to make sure you get to the proper tempt . so ck the connections and mke sure the thermo is good . . and the element is good . ..hope this helps mm . ... Jackson 10A Free-standing Dishwasher

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started. I have the same problem. Water flows thru the pump when not running, but no flow or goes in by-pass mode when I start the pump. The pump being Troy Bilt Model 020296-01. I replaced unloader valve even. Anything else I can do?


You replaced the unloaded valve. Are you positive you have the unloader screwed to pressure and not turned the opposite way? You will have no pressure if it is adjusted wrong. One other thing I have encountered is that the unloader has a ball bearing ... Pressure Washers

We recently purchased a new pump for our frigidaire gld4355rf dishwasher. The old one started making grinding noises. When we moved the dishwasher it had leaked due to a failure of an interior seal. Our new pump is now making the same grinding noise but it is not constant. When my husband adjusted the pump by using his hand when he got into a certain position the noise stops. We keep the screens clean. Is there an issue with the pump in this model?


... Frigidaire GLD4355RF Dishwasher

I have a problem with a bosch dishwasher i put in a kitchen 10 years ago. knob on left side buttons on right , stainless steel interior. i dont think client has ever used it. he must have put in new disposal but did not clear knock out. he went to use it with regular dish liquid.it started to leak and foam. he left me a note to look at it. 10 hrs later its still running and water is everywhere. i disconect from disposal and pump water into bucket but now can not get water to go in to it. tried b


First check that the valve under the sink is turned on sorry have to put this part in next thing to check would be the inlet water valve and assure that you do have power going to the valve if you dont then you would look at the float switch as the p ... Bosch Dishwashers

I have a model 5000g. it might have 15 hrs. total running time on it. when i tried to use it last it would not build pressure. i took the pump apart and cleaned and regreased it. everything looked good. ive got good pressure to the pump but just a small spray out the wand. when running there is no real load on the engine. it has always been kept inside in a warm enviorment.


... Karcher Pressure Washers

I have a Kitchenaid dishwasher model KUDS01FLSS2. I finished replacing the door balancer cord and started the dw up and it started leaking underneath from the bottom somewhere around the middle of the unit. This is when it first enters the cycle, so there is no water inside. I pulled the DW out and look at the hoses and components under the DW and all looks in good shape and could not detect any cracks. However noticed that one of the hoses (not sure what the hose is called) that connects to the


In this Kitchenaid dishwasher model KUDS01FLSS2, the whole motor and water pump assembly simply sits (I think loose) in the bottom of the DW. From the inside, it is the round mechanism where the sprayer is mounted above the chopper, all one piece sit ... KitchenAid Dishwashers

FDW60 dishwasher Hi My dishwasher is about 15 months old and the problem I have is that it seems to stay on pump and the Ecco45 light is flashing.  A repair company looked at the machine and said that the motor looked like it was leaking and water was getting in the bottom setting off the micro-switch.  He contacted Hotpoint who fitted a new motor today at a cost of £89.85.  Went to use dishwasher tonight and we still have the same problem.  The dishwasher started the washing programme for about


I've just (as of 10 minutes ago) had the same problem. I followed the advice given elsewhere in this forum and removed the bottom cover - water running out so needed a big towel to mop it up. I stood the machine upright and restarted it - no problem! ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Hello, I have a Frigidaire Dishwasher, model FDB750RCC1. It will not fully drain. There is water in the bottom of the unit after the cycle is complete. As it is not full of water or leaking out of the unit when I open the door I am suspecting it is the pump that has broken? (the water must be draining to the overflow point and then stopping as there is nothing pumping it) Any thoughts or ideas for me anyone? Am I on the right track?


... Frigidaire 24 in. FDB750RCC Stainless Steel Built-in Dishwasher

We have a frigidare model PLD4375RFC3 dishwasher that won't turn on! I select the cycle and press on and it just shows me the time for 15 or 20 seconds and then turns off. I opened the bottom and everything looks ok, there are no leaks and all wire connections are in place. Latley the motor has been squeeling a bit and the dishes have not been clean so obviosley something has taken a dump! I just need to know were to start, is it the water valve or circulation pump and how do I test them?


... Frigidaire PLD4375RFC Dishwasher

Have a NEW 3 weeks old dishwasher model no SMS69L12GB. Almost a pint of clouded water being retained in waste water pump area all the time after use. CHECKED area and it is spotlesss and no bkockag or kink in waste water hoseor no "E's being displayed on panel. Dont like the idea of stagnant water being in the DW. looking forward to hearing from you asap Annabeth


... Bosch Dishwashers

I have the two drawer model dish-drawer system. In the past the top seal leaked and since has been replaced with a new seal. Worked well for several years after but then the top drawer quit running. So we started to use the bottom drawer. That was fine for awhile althought it would pump waste water into the top drawer. Now neither drawer will work. The bottom drawer starts up and shuts down. I pulled the lower drawer and it is dry.


If your model has got an LCD display are you able to record what shows up on the display when the bottom drawer shuts down. If no display then are you able to note down the LEDs which are on inside the top of the drawer lid. It is likely there is no ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a Tappen whisper quiet dish washer model number 61-1160-10. My problem is that 2-3 hours after use the tub fills up with water and leaks all over floor. there is what looks like a "D" shaped vent or something on the left side of tub about 1/2 way down appears ther is a trickle of water comming out of this.


Ok here's what the problem could be. Under the dishwasher there is a water valve the is where the water line connects to the dishwasher, This may possibly be a blue valve. From the sound of your problem the valve is not quite shutting off possibly ... Dishwashers

Model 01902 2350 psi . engine runs fine , sprays out nozzle but lower pressure and water sprays out plastic elbow on relief valve , that is supose to **** in soap if used , cant hold finger over spray from elbow , high pressure , took apart relief valve and plastic valves all orings are ok , brass pump seals look ok , all back together , still blows out elbow . ?? plastic spools were out by somebody else , not sure if they are in right , cant find picture to compare .


It sounds as if the non return valve in the elbow is the wrong way around .The o-ring normally goes in first then the ball then the spring. Try it and good luck. ... Pressure Washers

I have a Bosch Model SHE43F Dishwasher, only 1.5 years old. The door will not lock all the way like the latch is broke. But the dishwasher still works as normal without locking the door. The last time I used everything was ok. Looks like a programming problem, or latch mechanism broken.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. From what you have described the\015\012issue seems to be with latch mechanism as the Dishwasher is worki ... Bosch 18 in. SRV43M03 Built-in Dishwasher

We need to replace the locking ring in the bottom of our Asko 1716 dishwasher.(It's cracked) I can only find one kind of replacement ring for that,but it looks like the right size. I need to know if Asko uses one ring for more than one model of dishwasher?It's a 5" locking ring for the bottom well of the tub. Thanks for your help!


Only 1 size ... Asko D1716 Built-in Dishwasher

I have a Honda xr2600 power washer. When I tried using it, water was squirting from the top of the gun. I took it apart to find that there are o-rings on top of some kind of washer---looks like a lock washer but it's made of cardboard??? Two of these washers were broken. I can get the o-rings but I can't seem to find the washers. I tried getting the manual for this model on line with no luck. Any assistance will be greatly appreciated.


The washers that you describe are made of teflon and are split to facilitate installation and/or allow expansion as they wear. These washers are actually seals and at times are used together with orings to seal high pressure. You should ... Honda Pressure Washers

Whirlpool model GU2400XTPQ7 (Canada) plastic tub has discoloration from heat element......plastic directly under the element has dried out and cracked....it almost looks like it has been eaten away......now I have a leak! Virtually impossible to fix without replacing the entire plastic tub. Of course because the machine is four years old, the warranty has expired. Is this a common problem? Heard of this before?What now???


... Whirlpool GU2400XTP Built-in Dishwasher

I have an EXCELL EXHA2525 pressure washer that I bought used - the front of the pump assembly consists of what looks like (2) pipes and it basically holds the assembly together, along with the fitting


... Karcher 2500 PSI Pressure Washer

Kenmore Dishwaher 58715142400 leaking from round looking pump on bottom. It was not draining so i unclogged the hose and put it back on. now it is leaking from a pump or something where it doesn't look like water should be at all


May be blocage in the exit pump ... Kenmore Dishwashers

GSD4911X02SS leaks from the bottom. Opened the bottom cover to see where the leak is and it looks like it's leaking in two places. The leak is ont by the door. It looks like the leake is by the pump or motor dripping down. The diswasher still works, but the leak needs to be fixed. Also I have pictures if you need to see


... GE 24 in. GLD6200L Built-in Dishwasher

Had the Northstar 3000 psi Pressure Washer for 2 months and it started leaking oil from the pump during use. Took it to Northern and they are replacing the pump under warranty but said it was likely because I was using quick connects on my garden hose coupling and that was restricting the water flow making the pump overheat. They said never to use quick connects on the garden hose unless the opening is at least 5/8". Does anyone make such a quick connect? I hate having to screw the garden hose o


It is easy to check if your hose and quick connects are supplying enough water to the pump. Your pressure washer gallon per minuite requirements are printed on the machine and also on the pressure tips in GPM. Your post indicates 2.5 gpm but check yo ... Northstar Pressure Washer 3000 PSI
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1585 seconds