Having problems with your Pressure Washers ?

I go to pull start it and it fires up but then it dies so i cleaned the carb out took it all apart and cleaned and put it back together and still same problem


Answers :

Usually there is both a choke and fuel shut off lever on the engine with the choke being gray and the fuel lever being black.

With the fuel line disconnected from the carb., move the lever back and forth while using a catch container and check the fuel flow. The lever should turn the fuel on and then off.

Also the tapered rubber head or the rubber seat for the float needle may be hard causing the needle to hang / stick in the closed position. With the float bowl removed... Use a catch basin, move the fuel shut off lever and check for fuel flow through the needle and seat.
I you have good fuel flow take a look at the float bowl retaining bolt... there is supposed to be 1 to 2 holes in the side of the bolt to allow fuel to pass into the jet. If the holes are blocked it will cause fuel starvation.

Thanks for using FixYa.

Kelly
Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I go to pull start it and it fires up but then it dies so i cleaned the carb out took it all apart and cleaned and put it back together and still same problem


Usually there is both a choke and fuel shut off lever on the engine with the choke being gray and the fuel lever being black. With the fuel line disconnected from the carb., move the lever back and forth while using a catch container and ... Pressure Washers

MAYTAG MDBH979AWS DOES NOT SEEM TO FILL WITH WATER, AND HAS STOPPED CLEANING THE DISHES..My husband took everything apart and we cleaned each piece and put it back together , there was no indication that anything was clogged, and he was able to determine that water was coming in to the washer, but dishes are still dirty. There seems to be soap residue on the bottom of the tub. We also check to see if it was draining properly and that was fine also. Any other suggestions?


... GE Dishwashers

My dishwasher does not sound correct (lack of spraying action sound) and this last time when I opened the door the soap had not disolved and the dishes where still dirty. I have taken apart the bottom arm before for a cleaning but it was only a couple of weeks ago. Could it clog up again so fast even when the type of dishes remain the same? Did I put it back together wrong? Maytag EQ Plus


DEAR FRIEND,\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012ngfam1 here for you!\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\0 ... Dishwashers

This is the 2nd time I've had problems with my dish drawer. After I cleaned the filter and replaced it, I had standing water on the bottom of the drawer. The last time this happened, I had someone come to repair it - ended up it was me. I didn't put it together properly. This time I did the same thing I was told to do. I still have the standing water. What should I do. By the way, the coils are not kinked in the back either. Can you please give me some advice? Please respond to me at F


Unfortunately I have to respond to you through this post per policy of fixya.com. This s to ensure we have a visibility on the quality of the solution and also allow other consultants to help if necessary.\015\012\015\012Water standing a ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My GE dishwasher Model # GSD2200GO2WW will not drain. I took it apart cleaned out the food particles that were in the filter basket and checked the hoses... put it all back together... Still won't drain. now what?


Did you check the drain pump? if you remove the pump and take an extension cord and cut off the end and add two connetion terminals to the end plug em in then plug them to a wall outlet you willbe able to tellhow well your pump is actually working if ... GE 24 in. GSD2220Z Built-in Dishwasher

Frigidare GLD2450RDS0, unit is approximately 5 years old. All of a sudden the water is not draining out of the tub in the bottom. Bailed water out, pulled the glass tap out and cleaned, pulled the lower sprayer out and cleaned, pulled the filter out and cleaned it. Put back together and ran a cycle...still left water in bottom. Help please!


... Frigidaire Dishwashers

Whirlpool mod # GU2400XTPS6 Loud during wash cycle. I've cleaned under lower spray arm...took it apart, all the way to grinder blade and screen. Cleaned out toothpicks, broken glass, shop-vac'd the area. Noise seems the same when I put it back together.


Hi\015\012\015\012If you have opened all the way to the impeller and cleaned\015\012the drain pump assembly completely then the issue is with the pump that is bad\015\012and should be replaced. You can also check this video for replacing/ ... Whirlpool GU2400XTP Built-in Dishwasher

I have a Kenmore dishwasher 665.17799990. Not enough water was coming in so I thought that I'd check the screen inside the water inlet valve to see if it was clogged. It was. I cleaned it out,but mistakenly opened the wrong part of the valve looking for the screen and took apart the diaphram assembly. Bad mistake. Now I can't get it back together without it leaking like crazy. I can't remember how it was configured to start with. I put it together once,but it wouldn't shut. I can't afford to buy


... Dishwashers

I have a MDBH945AWW that is just over one year old. It has just started making a various new noises. Grinding, loud buzzing and such. Still cleaned the dishes and completed the full cycle. I followed the solution that bgreenatown gave for removing obstacles. Found some soft material but did not seem that it would cause an obstruction. Removed it and put it back together but it is still making noises. Any next steps?


Hi,\015\012This soound is from the pump assembly. Looks like the "CHOPPER ASSEMBLY". Try to pull the pump apart and take a look.Go to www.sears.com and put in your model number, ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

Assembly plans for karcher 2400 psi pressure i recently had a problem, with my pressure washer. i was cleaning out my hose and took the hose assembly and brass fitting off. run water threw it thought i had cleand it out, put it back together and now when i hooked my water hose back up the water comes out of the despencer instead of the pressure wand. does eny one no what i need to do to revurse this?


... Honda Karcher G2400HH-R Pressure Washer

Took apart to clean and cant put back together


What part(s) do you need assistance with exactly? ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Kenmore 110763491 took apart the inside to clean it put it back together now it will not fill with water


... Kenmore Dishwashers

Machine stopped before end of cycle and did not drain. Cleaned out water, took apart pump assembly, impeller, etc. and drain hose. No obvious problem. Put everything back but dishwasher won't star


... Whirlpool 24 in. DU920QWD Built-in Dishwasher

Hi I have a Meile G 685SC Dishwasher. It has a water inlet problem. It will not fill and just keeps cycling through the water filling process with the water inlet light flashing. I have taken off the inlet pipe and removed and cleaned the inlet filter and washer and put them back. The filter was blocked with a sand like substance. I have taken apart the antiflood valve also attached to the inlet pipe but it is gel sealed so unserviceable. The inlet pipe itself on removing from the vlave appears


Check that the stopcock is opened fully or whether the water inlet hose\015\012is kinked...Check that the water inlet filter is not clogged and clean\015\012it, if necessary, as described in the operating instructions....Check\015\012that the drain p ... Miele 24 in. Incognito G643SCVI Built-in Dishwasher

The maytag dishwasher model mdb7130AWB stoped cleaning correctly so we went from the arm assembly in bottom of dishwasher down to the cutter disc and we found a crack in the housing so i ordered that piece. the new part was designed a little different but we put it all back together the way it came off. but it started and ran maybe 1 minute and stopped. so i have pulled up the diagram and see some problems. in the current diagram. original there was no part 37, 17 19 and 3, alos the crew d


... Maytag MDB7130 Dishwasher

Karcher 2400R I have not used my pressure washer for 6 months. It was left full of gas in the garage. I tried to start it but it would not fire up so I change the gas, oil, and spark plug, took apart the carburator and cleaned it out with carb cleaner. I went ahead and put everything together, pull the cord and wanted to start. While trying to start it after I sprayed starting fluid in the air cleaner I noticed that gas was coming back from the crankcase breather hose into the air filter choking


You have a poor signal to the spark plug usually caused by a rusty fly wheel found underneath the pullcord casing. clean it with releasing ajent such as wd 40. common when not in use for a while. ... Karcher 2500 PSI Pressure Washer

Runs fine gc160 wont give me any pressure. i took the pump apart and cleaned it then put it all back together the pressure was intermediate but now nothing at all


If you give us a bit more information we may be able to assist!is it a pressure washer you are trying to get running.the number you give is the model number of the honda engine. 5.5 hp honda domestic use.what does the pu ... Karcher 2500 PSI Pressure Washer

I took my dishwasher apart to clean it and get better draining put it back together and now it won't work


... Frigidaire Dishwashers

Hi Model DU1048XTPQ4...when I started the DW today, it sounded kind of loud. I let it continue, then I smelled something burning. What I think happened is that the lower spray arm is too loose-so when it spins, it gets stuck on the heat ring on the bottom of the DW and then the plastic parts start to melt. We disassembled the spray arm and there was lots of calcium/lime build-up. So we cleaned all of that out, put it all back together, but the spray still seems too wobbly. Went ahead and start


The noise coming is from the motor bearings or the impeller which moves with the motor.both has to be checked.\015\012if the bearings are making noise motor needs replacement and if impeller is cracked it needs replacement.\015\012you can get require ... Dishwashers

It sounded like something was jammed in the bottom of dishwasher. Took it apart, not sure if put it back together correctly because now it is not turning (bottom). Is there a diagram to look at on how to put back together correctly? Whirlpool Quiet Partner II Serial # FP1386450 Model # DU943PWKQO


Go to sears part sales web site adn look at parts breakdown. ... Dishwashers

Hi i have a bosch model no sgs53e02au australia 2 weeks ago put a wash through over night woke up in morning noticed still making noise opened up the door of dw still making noise sort of brrrrr noise constant not stopping unless press botton off would turn off still had water in bottom rang company they told me to clean filter which i did found glass particules took water out with sponge clean it rang back they told me to get a piticuler tool size 20 to unscrew and pull out pump sat there unscr


... Bosch Dishwashers

I Have a amana sofsound 1 dishwasher. i took the bottom arm and traps out to clean them. now i cant getit put back together


... Amana ADW862EA Built-in Dishwasher

We have a newer bosch unit and it worked well in the beginning. Lately, we are having problems with dishes coming out not clean - bits of food still left on glasses and plates. Now we are scrubbing them clean before we put them in the dishwasher and some still come out with food bits on them. What is happening?


Check that the soap dispenser opens correctly ... Bosch SHE4AM16UC 24 in. Built-in Dishwasher

Zanussi dw927 not filling inlet valve changed,supply to machine ok, calls for water solinoid activates for about 30secs shuts off and machine does no more. cleaned out two blue plastic pipes situated under a plastic cover which were both blocked, and put a hose jet wash thru where they were situated to clean housing out, put blue channels back still not filling up and now the inlet solinoid wont switch off when when it should and programme advances heater now comes on with no water in.manually


... Dishwashers

Mod #: MDB6600AWB Ser #: 16505148CG No water comes out of spray arms, checked and cleaned filter-OK. Wash impeller is cracked where it slides onto the hexagon rod but it you take the filter flow plate off and put the impeller back on, when you put the unit on rinse only and quickly open the door you can see it is still turning and moving the water. The unit still fills and drains. it just does not have enough force with the impeller to force the water into the spray arms.


Hi,\015\012 \015\012Please check the bellow link regarding your query....\015\012 \015\012 ... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1488 seconds