Having problems with your Pressure Washers ?

Where to get pump bearings for a rockworth pressure washer


Answers :

IF you can get the bearing out to see if there is a number on it, depending on where you are, you may have to take it in to be identified, check with either Motion Industries, Applied Industrial Technologies, Bearing Distributors or Kaman Industrial. All are bearing distributors that should be able to help you.
Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Where to get pump bearings for a rockworth pressure washer


IF you can get the bearing out to see if there is a number on it, depending on where you are, you may have to take it in to be identified, check with either Motion Industries, Applied Industrial Technologies, Bearing Distributors or Kaman Industrial. ... Pressure Washers

Home Depot has a lawn mower with the Honda GCV160 Electric start version engine. They also have a pressure washer with the Honda GCV160 engine. I have a disability that makes it difficult to pull the starter rope. I would like to get the electric start on the pressure washer. My local Honda bike shop service center said they use different blocks. Can I get a pressure washer pump mounted to the Honda GCV160 Electric start version engine? If necessary, are there adapter plates that can be purchase


... Karcher 2500 PSI Pressure Washer

Briggs and Stratton Troy Bilt gas pressure washer one year old. I can get water thru pressure washer and bleed the air, water comes out the hose just fine until I start the pump. Then, I lose all water flow. Pump runs fine but when it's running, no water goes through.


... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

I have a McCulloch FH160B power washer and it no longer builds up pressure. I haven't used this very much at all. I tore it apart and cleaned everything I could find. When i pull the trigger for the spray nozzle, I get line water pressure. When I release the trigger, the power washer sounds like it starts to build up pressure. When this was working correctly, the pump would shut off when the trigger was released. Any suggestions?


... McCulloch Pressure Washers

I have a model PW 2200 gas pressure washer. It suddenly lost it's high pressure the other day after working fine for @10 minutes. It's getting plenty of water, but the engine doesn't seem to rev up to give it the high pressure. The operating instructions say to check the oil in the engine, and the PUMP before starting, but I haven't found any place to check for an oil level in the pump????Any ideas, I'm very confused.


... Pressure Washers

I have a ANNOVI pressure washer and I can not seam to get the engine apart from the pressure pump. All bolts are removed and the bludy thing will not come apart. The lock nut on the drive is not even


There may be no good news for you. Once those hollow shaft pumps seize to a engine shaft, they can be real buggers. In fact, they can be impossible. But before you give up and completely destroy the pump to remove it from the shaft -- the ... Pressure Washers

I have two DeVilbiss issues: First, on my pressure washer, I no longer get pressure on "high" mode from the hose. I prime the pump but it doesn't seem to be creating enough force for a high pressure. Second, on my generator, the gas from the gas tank leaks out. The tank is plastic or poly and don't know if it's a gasket issue.


... DeVilbiss Pressure Washer Hose 3600 Psi 25'

Troy- Bilt pressure washer #020209 , 7.25 Briggs & Stratton, AR water pump #SJV 3G27-1. Boggs down an cuts off acts as if motor is getting tight with wand in use or not. After shut down its easily starts up an repeats itself. Removed pump motor runs fine.


... Briggs & Stratton Power Products 1539 Pressure Washer

We want to replace the pump to our DEWALT DP3750 pressure washer and can not ge tthe pump to come off the engine. how do you get it to come off?


... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

Will not get prime,will not pump pressure. - Honda Pressure Washers


Hi,Could you please supply your model number so I can check and see what particular parts you have. Not all models are alike...Thanks,Handie Andie ... Honda Pressure Washers

Pressure Washer I have a Porter Cable pressure model no.PCH2401.It works fine for 5 minutes,then I can hear the motor loading down and then it stalls out. I tried to start it and it was very hard to pull on. disconnected the water supply and if was very easy to pull and started right up. I noticed the pump was very hot.This unit has a thermal relief valve on it,shouldn't it have released when it gets to a certain temperature .I was thinking maybe this is why it might be shutting the motor


Any leaks from connection at pump to gun and wand assembly if so the valve is detecting leakage and open up again without u squeezing trigger it builds up in the head.if your trigger gun is leaking internally then you will need to replace the gun thi ... Pressure Washers

The oil in my gc160 Honda pressure washer is getting water in it some how. Could it be something with the water pump gasket or what? And I can get it started but can't keep it running un less I keep spraying starter fluid in the carbar. Please help ?


... Karcher 2500 PSI Pressure Washer

My pressure washer is not pressurizing the water. i took the bottom assembly off the pump and there are three spring loaded plastic pieces in there. underneath these springs is a mushroom shaped plastic piece. two of the three mushroom pieces were contorted and need to be replaced. how do i get them?


Craftsman 2200 psi pressure washer 580.752341 ... Pressure Washers

I can't get the igniter to start on north start pressure washer #157224. Fuses ok, indicator light in heat switch does not illuminate. Blower works, fuel dripping out. Cleaned fuel tank and pump and filter too! Tried jumpering past the thermostat didn't help either. Also, swapped pump and heat switches on main panel. No help!


... Pressure Washers

I was given a low hour, 10 year old, CH PW205002LE 6.5 HP gas vertical shaft 2000 PSI/2.5 GPM pressure washer with a Lavor pump. It did not work - no pressure. I found a broken o-ring on the brass unloader valve and replaced it with a ring as close in size as I could find as the part break down doesn't state size. Everything was very clean. I coated everything with silicine grease and reassembled, seating the brass piston? as deep as it would go. I had to press the trigger in order to get the mo


My personal experience is that 40% of all the sellers I dealt with on e*** exaggerated their products or worse. If you decide to go the e*** way be sure you put it on a good credit card so you can get your money back if it's a bust. Don't use your ba ... Campbell Hausfeld Pressure Washers

PW 135000AV Dear sir or Medium, My PW 135000AV pressure washer has damage the bearing at the front of the armature. I have to take the Gear off from the armature to get access to the bearing could you tell me if the gear press on or is it screw on if it screw on is it right or left hand threads. Thank you Sham Birball.


K after my last post did some more checking and went to the Campbell Hausfeld website and found your unit but no breakdown for this. I would suggest that you try their site and ask them to send you a PDF file on the tool. Also they have a year warran ... Campbell Hausfeld RBPW1350YL NA 1350 psi Electric Universal

Water Diver Series pressure washer, model WGV1721 shut off when running and the pump gets so hot I can't keep my hands on it.


... Briggs & Stratton Pressure Washers

How to get pressure washer to spray shop force 1300 psi pump working


... NIB Shop Force Universal Pressure Washer Accessoriesnib

My Karcher K3.48M pressure washer remains in the low pressure mode even when I return the pressure nozzle to the high pressure position. How can this be corrected. The pump seems to build up the pressure because when I release the handle the pump motor stops. This is a fairly new pump which was purchased in the latter part of last year(2010). Could this have been caused by the detergent I have been using which is an automotive shampoo? Please help I love this washer and for the times that I u


... Karcher PSI Electric Pressure Washer

My washer no longer cleans the dishes. the functions all work but it appears that the pump pressure is too low to get stuff off the the dishes.


Hi,When my wife started complaining about her dishwasher not getting the top rack clean this is what I found and I wrote a tip about it...Dishwasher ... Bosch SHU9925UC Built-in Dishwasher

Where can i get instruction manuel for rockworth pressure washer arowfm4p


... Pressure Washers

My 6 hp honda motor has become very hard to pull. It is on a pressure washer. I even removed the pump but still pulls hard.it runs if you can get it started but dosnt seem to be running at full power.I pulled the spark plug and it spins easily. Help!


When you remove the spark plug and it turns easily that means that the valves aren't opening properly. When the spark plug is installed and its hard to turn over, its because the valves (possibly just the exhaust valve) are sticking shut and the pre ... Pressure Washers

I have a NorthStar pressure washer M157471A.It has started leaking from the pump. I have stripped it down and would like the valve kit A and the piston seal kit B item 5026 0257 and 5026 0256 . Were will I get these from?


NorthStar is a Northern Tool housebrand. You can contact them using the information below, and order the parts that you need.Contact a Northern Tool Product Expert:Call 24/7: 1-800-221-0516Alternatively, you can also or ... Northstar Pressure Washers

I have excell 3700 pressure washer...the pump cover vibrated loose lost oil and cam melted.how do i get parts and change pum cam?


When you get down to it, purchacing oil end parts for a pressure washer is not cost effective.\015\012\015\012The crank(cam) shaft runs about 280.00 dollars. The oil seals, new bearings, possibly new pistons and almost definatly new seals ... Psi PowerBoss 20262 Pressure Washer

I have a HDS 950 er915 I have the pressure washer working but can't get the steam cleaner to ingnight the spark is working all the time even when just on pump but it will not inject oil even on full heat setting with burner switch on


The fuel pump is controlled by several things. A flow switch, a thermostat, a pressure switch. All must be working for the heater to work. Also you said inject oil. I hope you mean diesel fuel or kerosene. It won't burn oil. ... Karcher Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1317 seconds