Having problems with your Pressure Washers ?

11hp washer new not sucking up water from barrell with or without lance


Answers :

Try putting the machine on mains water pressure first to get rid of any air in the system then try it from a barrell.
Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

11hp washer new not sucking up water from barrell with or without lance


Try putting the machine on mains water pressure first to get rid of any air in the system then try it from a barrell. ... Pressure Washers

I have a Bosch SHU9915UC/U11 dishwasher, installed in 2002. Recently, our hot water heater had to be replaced, and we were without hot water for five days. Air got into the hot water pipes, and dried out all the debri in the lines. When we got the new hot water heater going, all of the sediment in the pipes ended up in the in-line screen filters in various appliances (clothes washer, etc.). I have cleaned these out, and these appliances are fine. Since then, the dishwasher has been shutting


All inlet valves have a screen built into the valve itself,shut off the water remove the entire valve and you will be able to see built in screen,if you flush out the debris from it and re-install the valve it should work fine.  ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I have abrand new Black and Decker 1900 psi pressure washer. When I hook the water hose up to the machine and turn on the water, water sprays out out of the bottom without the machine being turned on. Thank you


... Pressure Washers

Briggs and Stratton pressure washer will not start. I have a 6.75 hp pressure washer that is only a year old. when I pull cord it turns over but does not start. I changed plug and checked it, I have spark when pulling. I have 40-50 psi of compression when pulling also. gas was drained and is brand new. it was working fine last time it was used. I have tried starting it without the water line or spray wand hooked up and no difference. After about 10 or 15 pulls, can smell gas when I am trying to


Hello dave, the problem is compression to low,you need 60 to 130 lbs to run engine,check for blown head gasket,or bad rings,or a stuck open valve,hope this helps,, ... Briggs & Stratton Pressure Washers

Have a 11hp power washer pump not sucking water, how do i fix ?


Hey there...Is the washer a direct drive or belt drive unit? If it is a direct drive ( the pump bolts directly to the engine) then the pump needs to be force fed the water, either by city pressure or a transfer pump. If it is belt drive ... Honda 8 HP Engine

My Bosch dishwasher is off but water continues to over fill base.I'm not using the sink. I've sucked the water out with a wet dry vac three times in the last 2 hours. I've also sucked the water out of the pan underneath the washer. The water is coming from the ''side hole'' not the drain hole.


You will need to turn the water supply off at the wall as the fill valve has got some dirt in it and cannot close properly\015\012\015\012To clean it out is a strip down job so unless you are mechanically minde then it is down to a repair ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a troybilt 3300 psi pressure washer with a gx390 honda engine. Replaced carb with new one . washer now will start and runs fine under load but let off water and carb goes up and down and backf


... Pressure Washers

On the MIELE G881 SCI plus -3 the cycle stops after about 2-3 minutes (enough time to purge the remaining water and fill the dish washer with new water). Then after 10 minutes it abandons de cycle and shows the red light "intake - purging". When i open the washer, the water inside is NOT warm.


Hello, Welcome to FixYa.I'll start by saying on many Miele different issues can manifest in a similar scenario, water valve, leaks, etc. and then the error lights. ... Miele 24 in. G656SCi Plus SS Built-in Dishwasher

I have the Coleman powermate 2400 PSI pressure washer and on initial start it sprays and has great pressure. But once I release the spray handle it will not spray again, not even one drop of water. I have verified water pressure, bought 3/4 hose, and also changed the spray handle with no help. Pressure washer was bought new at Lowes, but did not use for first three years of ownership, should have tested it. Thanks for any help on this. Ted Miller


Sounds like the valve in the handle is sticking closed. May have a broken spring, or maybe a part is stuck..\015\012I say take it apart, and the answer will present itself.. Play with it with nozzle out too... Maybe something is stuck after st ... Coleman Pressure Washers

Water was turned off while we were on vacation. Wife ran dishwasher without turning on the water. Turned on the water this morning, however unit won't pump water into the washer .


\012Hi,\012Here is a tip that will help you to find out why water will not come into the dishwasher... ... Maytag Dishwasher

The washer cycle stopped without warning, i thought the timer or the timer motor but it is not the timer works fine and so is the motor. but the timer motor runs til the washer motor starts than is the timer stops and the washer is working but not cycling so no rince or drain or soap etc... just pumping water. if you can tell me what might be the problem, thank you. like i said the timer stops when the washer motor start.


... Jackson JPX-300L Dishwasher

Pump problems mine is the 14w. all that happens when i turn it on is the pump tries to drain the water, but there is no water to drain as the cycle has not started. all you can hear is the pump sucking water. no water comes into the washer either. somebody please save me.......


... Zanussi 18 in. DCS12W Free-standing Dishwasher

I have a McCulloch FHH18A power washer. When plug it in without the water turned on, the pump will start. As soon as I turn the water on to the unit, the GFCI power cord trips. Water does flow through the unit as I have water at the wand nozzle when not plugged in. Any suggestions?


I would guess there is a leak somewhere inside the unit that is spraying water on some electrical component and causing a ground fault. ... McCulloch FHH18A Electric Pressure Washer

Ran 1600s washer without water.


... Stanley 1600PSI Pressure Washer w 20ft Hose Accessories

I am having trouble attaching 90 degree brass elbow to the plastic water inlet on my new Maytag Dishwasher. Getting leaks. Teflon tape hasn't worked. Cant seem to get the washer to seat properly when everything is tightened down. Wish the water inlet was not made of plastic. It appears it would seat the gasket properly if the water inlet was made of something more durable.


Hi!!\015\012\015\012Have you tried pipe cement, the plastic to metal kind will take care of any leaks. You can find it at any hardware store.\015\012\015\012Good luck! A HELPFUL - 4 THUMBS - rating for this solution would be greatly app ... Maytag MDB8959AWS Builtin Dishwasher

The Nilfisk Alto150 washer roof cleaning lance didn't move the moss even with additive. The standard lance does and cleans the tiles to a lovely biscuit colour as when new in 1951. How can I boost the pressure in the extending roof lance to do this so that I don't have to clamber all over our (bungalow) roof


... Electric Eyeware Electric Pressure Washer 1500psi Etq2000psihr

Dish washer Hi there, Last time I started my dishwasher, clear water spilled out in a large amount. We pulled the washer out to realize some plastic parts underneath had totally smashed down. Is it possible to replace those parts, or do I need to buy a new washer?


Yes youcan replace them just give dishwasher name ? ... GE Dishwashers

What could be causing white powdery residue on dishes, glasses & silverware? I have checked the heater element - seems to be hot, using Cascade powder as usual, we have and have had hard water, we do have a new water heater set on 'low' setting - temp of water measured at 113 deg at kit tap. This washer has worked well for 12 years, then white powdery residue. Thanks, Phil


I wont vista ultimate product key ... Kenmore 13869 / 13864 / 13862 Dishwasher

My built in Whirlpool adg 9340 washer won't start a cycle at all. It seems to start a cycle and after 1 minute it stops and it starts beeping. Also water remains on the bottom. As soon as the cycle starts it drains that water and brings new water in which stays there. It won't work for more than 1 minute....


... Dishwashers

"Sensing" Light Moved a 5 year old dishwasher that was functioning just fine to a different location. Hooked everything up and gave it a test run without any dishes in it. Fills and heats water properly, then buzzing noise heard for a ling time and then it drains the water out, with out circulating the water into the washer arms, etc. Any guesses? Could something have gotten lodged in the pump during transport?


There is a relay on the soap dispenser, if it is a Kenmore quietguard 4, I had the same type of noise, the repairman replaced the dispenser, which to me made no sense, because the relay is activated from the control board. After the $130. for the soa ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Coleman power washer PW0912201. Water is blowing out of the chemical pickup tube when water hose is turned on prior to starting. After starting the water realy blows out from there. Would the unloader be faulty? I tried to pull out the unloader stem assembly from the manifold but it appears to be pressed in. Do I need a new manifold kit? or am I looking at the wrong part to correct this?


... Coleman Pressure Washers

Pressure washer will not stay running. Have put in new fuel, new plug, new oil. Will not start until I spray some ether in carb, then it will start and run for about 3 seconds, then stall. will not restart without another shot of ether. What should I try next? thanks


... Briggs & Stratton Gas Pressure Washer 20244

I can not get the water to drain during a normal wash cyclr. When I press the start/restart button twice it makes noise but no water comes out the end of the drain hose. I have put a shop vac on the end of the hose and can get water out that way but it appears not to be pumping. The washer sits for up to 6 months at a time without being used. Thanks for any help Ted Berry Placencia, Belize Central America


Teddy,\015\012\015\012Buy a new one...then go fishin!\015\012\015\012Richard Vantine (ret'd Colonel...USAF) \015\012Bingelrade, The Netherlands ... GE GSD5310D Dishwasher

Constant draining my candy cs445 17" is stuck on drain, it just sucks water out and wont stop. Turning the dial to stop does nothing, if i fill it with a sacepan of water it juts empties, and when all the waters gone its just keeps emptying, would a float switch be the problem or possibly a new dial ?


I would check the float.clean it up real good.make sure it moves freely.let me know ... Candy 17 in. CS455 Built-in Dishwasher

My dish washer is not draining the water, I have a garbage disposal but its junk I am going to get a new one in a month or so it has a hole in it, I took the line going to the disposal off it had a lot of stuff in it but no water was coming out, I then took a vaccum and some water started coming out but did not continue any guesses?


If there is no blockage then the pump impeller or the motor has failed. Only disassembly will locate the real issue.Eric ... Frigidaire 24 in. PLD2850 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1794 seconds