Having problems with your Pressure Washers ?

Just put in new beckett fuel pump on burner not getting any diesel through it


Answers :

Make sure that you have turned the fuel tap back on.
\012and that there is fuel in the tank.
Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Just put in new beckett fuel pump on burner not getting any diesel through it


Make sure that you have turned the fuel tap back on.\012and that there is fuel in the tank. ... Pressure Washers

North star eletric hot 2000 psi 3.5 gal per min oil pump had blown shaft seal. replaced with new pump. put small allen plug in return port. I have oil flow to the pump but none comes out port leading to burner even with shutoff switch removed and pump turning. Installed test gage 0 pressure. Took off bypass line and ran into can. pumps small amount of fuel into can that way but with uneven flow & small bubbles. nomatter what I do I just can't get fuel outlet port to burner. pump # A2VA-7116 pl


... Northstar Pressure Washers

Fuel pump not working when trigger pulled, all temp. lights on. checked flow switches all ok and new fuel pump coil an stalk fitted. the burner will work if the o ring removed from bottom of stalk allowing fuel through so something is stopping coil from getting 24v(it does get a nominal voltage of 10v)... anyone got any thoughts


... Pressure Washers

I have a problem with a bosch dishwasher i put in a kitchen 10 years ago. knob on left side buttons on right , stainless steel interior. i dont think client has ever used it. he must have put in new disposal but did not clear knock out. he went to use it with regular dish liquid.it started to leak and foam. he left me a note to look at it. 10 hrs later its still running and water is everywhere. i disconect from disposal and pump water into bucket but now can not get water to go in to it. tried b


First check that the valve under the sink is turned on sorry have to put this part in next thing to check would be the inlet water valve and assure that you do have power going to the valve if you dont then you would look at the float switch as the p ... Bosch Dishwashers

Hotpoint Aquarius DWF32 dishwasher pump replacing instructions, how do i get at the old pump the put a new one in.


Its easy just uninstall the dishwasher and flip it on its back .i know it sucks but once the unit is out its no problem. ... Dishwashers

My bosh dishwasher SHX55M06UC/46 will not drain. A new disposal was put in and the dishwasher drain plug was not punched out and the dishwasher was ran that way. Now it just holds water in the bottom. I've tried resetting or canceling the wash cycle but that doesn't work and the washing cycle works fine. I'm hoping there is a reset or a safety for the pump if it gets clogged.


... Dishwashers

Have a Kenmore Freestanding Dishwasher that was working when hooked up to the sink. When we plumbed it in and connected the electrical directly, we now get an "F4" flashing on the panel with a beeping noise and the pump sounds like it wants to drain but just get a sucking noise. I've tried putting water in it to prime the pump, but still doesn't want to work. Do the codes mean anything, or point to a specific part?


... Kenmore 24 in. 16332 / 16334 / 16339 Free-standing Dishwasher

I'm getting F 84 which i'm told is failure of the divertor. A new pump is more than the value of the machine. What can I do? Can I get a reconditioned pump, or can this problem be fixed?


That was a very expensive dishwasher...I don't know what you were quoted but I did find one site (British, of course) that offers replacement pumps for far less than the cost of a new Miele...hope this helps... ... Miele Premier-Plus Built-in Dishwasher

Hi I went away on holiday and my dishwasher AEG 50800 was in perfect order. When I came back after three weeks it does not work. It was not in use while I was away so I don't get how come it is not working now .It does start up but its like the pump is just not kicking in. Ihear water running but the blades dont move and nothing seems to get washed, any ideas. Or is a new expensive pump my only option? My Husband seems to think a seal might have gone. Can a seal go while not in use? Thanks


It's worth looking under the machine. There is an overflow area with a float switch which sometimes fills up and it stops it working ... AEG Dishwashers

We have a commercial Hobart dish washer Model # AM-8T2; Serial # 240461. We cannot get the wash temperature to go above 120' to 150' as the burner does not light. The pilot is on. A new thermocouple was installed but made no difference. The rinse temp goes up to 180'. How can we get the gas burner to light and stay on. Thank you. Gery Spory


Hello Gery - get the repairman back who installed that thermocouple as that repair includes making sure the unit is working properly. Most likely the thermocouple is simply not warming up enough to operate correctly. It may be that the pilot light ... Hobart Dishwashers

Danby ddw497w will only be about 5 min into cycle when digital code E2 appears it then starts beeping 2 min after this it just stops the unit is only one day old it ran once yesterday fine now i get this code no matter what cycle it is on I bought mine new off the internet and it's been running great for about 2 months. Now I can't get it to drain and E2 shows, I can't get my money back because I've had it more than 30 days, if the solution is a pump, I'm tossing it and getting a good one from


E2 is a hose issue. There is either a kink in the hose, the hose is too high to drain or the pump is faulty.1-800-26 DANBY ... Danby DDW497W 22 in. Countertop Dishwasher

Brand new Northstar hot water pressure washer, 2000 psi, electric and Diesel fired burner. The burner will not come on??? It works ok as a cold water unit but the burner will not fire even with the Heat switch on and fuel in tank?? What could cuse this?


... Northstar Wet Steam & Hot Water Pressure Washer with Honda Engine 3000 Psi, 4 Gpm

Karcher HDS650 steam cleaner. I get white smoke when the burner strikes up, it does not get that hot although it does get very warm, also it surges as if the pump has no water in it, it does work but


... Karcher 2500 PSI Pressure Washer

My Diesel Fired Burner on my Hot Water Pressure Washer leaks diesel below the Hot box. It has new diesel from the gas station..


... Shark Helmet Shark Professional 3000 PSI (Gas Hot Water) Pressure Washer W Honda Engi

Our church has a Toastmaster Commercial Dishwasher with a Franklin Electric recirculating pump assembly that is making a bearing noise. We may need a new pump motor or pump. Do you know where we might get one?


... Hobart 41 in. AM14-255 Free-standing Dishwasher

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Hi,This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder ... Dishwashers

Dirty dishes Pump went on this machine about 6 months ago. Since the install of the new pump the dishes do not come clean. Particles finely ground or tomato seeds, sesame seeds etc. get blasted back on the dishes in the final rinse cycle. Repair guy has no clue... could there be a pinched line upon install that won't allow complete drainage, or the wrong pump? Is ther filter screen? I have done the vinegar reoutine plus a purchased cleaner to no avail. The machine is a bout 13 years old. Thank y


... KitchenAid Dishwashers

Hi just had new dishwasher put in its a diplomat intergrated dishwasher aca9102, only used it once and started beeping towards the end of the cycle. thought it might be coz i didn't put salt in it, and had tablets instead of detergent so put salt in and detergent in but couldn't get rinse aid. started the program on normal wash but started beeping 10 beeps straight away and the first three lights out of 6 are flashing on the control panel. could it be coz theres no rinse aid in it? please someon


Dear tracy83, \015\012\015\012we have an aca9102 diplomat dishwasher since april 08. we now have a fault with dishwasher but cannot locate our manual. could we arrange rto have a copy of your manual? sorry for being up front but cannot ob ... Dishwashers

My new dishwasher is not draining. I can hear pump going but it is not pumping out the water. It has not drained in the past but everytime I put on garbage disposal and a start of a cycle on dishwasher it always pumped out water. It is only two months old


... Frigidaire Dishwashers

My dishwasher starts but the main pump does not go just put in new pump


Check whether the pump power is getting ON. If not check the wires and the relay attached to it. ... Bosch Dishwashers

G851 SC Plus started to trip GFI plug. Called Miele and they said there was nothing wrong with the dishwasher and the GFI was faulty. Unplugged from GFI and plugged into regular plug and it worked for a few days. Eventually stopped running. How wrong Miele was, it had everything to do with the dishwasher and not the GFI. It was only warning me a problem was coming. Appliance man came out, noticed water in bottom pan and order new pump, said seal probably gone. Came back, replaced the pump, put d


... Miele 24 in. Novotronic G851SC Plus Built-In Dishwasher

I have a Husky 2600 PSI power washer with the Honda GCV160 engine that I can't get to start. It was okay when I purchased it from Home Depot last spring but now I've tried putting new gas in it, spraying carb cleaner, new spark plug, and it still won't start. I only ran it for about 30 minutes when I first purchased it. The guy at the service desk at Home Depot told me that the water hose should be attached and turned on while trying to start. Is this true or would this be starting the motor und


You can eliminate the motor by unbolting the pump from it and then if it will start the problem is with the pump or the unloading valve.If it does not start with the pump removed then you check for spark and get the carb cleaned or have a kit put in ... Karcher 2500 PSI Pressure Washer

The Bosch plastic push button (AP2804452) has broken on my SHU9950 dishwasher. The switch itself is still good. I have removed the broken pieces of the bad button from the unit and am now depressing the switch without the button. When I get the new push button, what is the proper way to remove the control panel cover to put the new button in place? Thanks!


... Dishwashers

Screw drop Hi I was installing my new LG dishwasher and I droped a screw in the hole in the side panel where you can put a screw to connect to the side of your cabinet. There is a small plastic cover which I removed where you can screw a screw into the cabinet. However the head of my screw was too small and fell in the side panel. I can not get the screw out or see it now although I know it is in the dishwasher. Is there anyway of getting it out or will this cause a problem? Since it is in t


A great retrieving tool for this is a flexible shaft magnet wand. I strongly recommend this tool be placed in everyone's toolbox.\015\012\015\012as far as leaving it there if not found? probably safe from electrical. will years of vibration allow it ... LG 24 in. LD-12BS6 Stainless Steel Free-standing Dishwasher

My Whirlpool GU2400XTP dishwasher keeps blowing the fuse. It sat up for 6months because the control panel went out and I couldn't afford to get a new one. Finally replaced the panel and the thermal fuse blew during the first wash cycle. I tried to put a 15AMP fuse in it's place to check it out before I bought a new thermal fuse and it too blew during the first cycle. Any ideas?


Are you replacing the wires along with the fuse? It is important to change the wires too as they are usually the cause for the fuse blowing. Be sure and get the fuse kit that includes the wires. \015\012\015\012Is your water too hot? Hot ... Whirlpool GU2400XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1361 seconds