Having problems with your Pressure Washers ?

I have a delta DTH2450 wont start wont pull over


Answers :

Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a delta DTH2450 wont start wont pull over


... Pressure Washers

The rip cord wont pull to start pulls once and then wont pull real hard to pull


Try squeezing the wand when you are starting the motor.\012it will let the water pressure go through. ... Honda Pressure Washer PSI 3000

2050 PSI Gas Pressure Washer - 20244: my excell pressure washer wont start. pull start t...


... Briggs & Stratton Gas Pressure Washer 20244

I HAVE A NEW CRAFTSMAN PRESSURE WASHER WITH KEY START. I HAVE USED IT ONCE AND WHEN I TRIED TO START IT IT WAS HARD TO START HAD TO PULL START IT. NOW IT WONT START. LET PRESSURE OUT HAVE HOSE OH AND RUNNING, NEW SPARK PLUG HAS OIL, GAS FILTER FINE.HAS GOOD COMPRESSION, BUT WILL NOT FIRE GET SOME RECOIL. GETTING GAS TO SPARK PLUG AND GETTING SPARK. IM LOST PLEASE HELP.


... Pressure Washers

I cant start my power washer. the pull start is locked and wont release to start engine.


When the pull start gets locked, you have to release water pressure from the wand. I had the same problem last year. ... Craftsman 2700 PSI Briggs Stratton Powered Pressure Washer

Neff dishwasher our dishwasher is six years old and have had no problems till now . there is power to it but when you push the on button the impeller starts up even when the door is open , and it wont go through the cycle , its asif there is no water going in and it is not draining away i have checked and cleaned the filters but nothing, then pulled it out from undre the sink and it started working . i put it back , it went through the cycle then the next day it would'nt work again . do i need a


You have a faulty door switch. It can be replaced and may be available at youre local appliance parts dealer. ... Dishwashers

I have an almost brand new husky pressure washer (one of the big ones). It has been a life saver so far. just the other day it shut its self off. its gas powered so of course i checked the gas and oil. then tried to start it back up. but when I try to pull the pull string it wont come out more than about 3 inches. i payed 400$ cash for it to use on the trucks. does anybody know how to fix that? thanks


IT SOUNDS LIKE YOUR FLY WHEEL IS BAD OR NEEDS TO BE ADJUSTED ... Pressure Washers

Telmann Dishwasher TEL 12DWM. Dishwasher started to make weird wooshing start-stopping sounds at the beginning of the wash cycle so I stopped it. Since then the lights are on but wont go regardless of where the switch is set to. Have pulled the pump off and the inlet pipes and blown to remove any blockage but still no luck. Cant get into the water jet part due to connectors that require specfic tools to remove and replace. Any thoughts?? thanks in advance, Michael


... Dishwashers

Mdb6709awb1 wont start anymore at first i had to pull up and hit start key severa times to get it to go now nothing..


... Maytag MDB6709AWB - MaytagR JetcleanR Plus Dishwasher

The cable in my Husky Gas Power Washer wont pull start


... Honda Pressure Washers

It wont start...i have only used it once in 1.5yrs...just put in new oil and gas...I give it a pull but does not ignite.


... Karcher 2500 PSI Pressure Washer

I have a Whirlpool Quite Partner 2 I pulled it out and unhooked it to instal a new countertop and now that I put it back and hooked it up it wont start, It has power and water pressure, the door is shut. what could be the problem ?


Hi.Check the contact to the inlet valve, where you hook up the water hose. If you have disconnected the inlet valve, the machine will not start filling.Try disconnecting power for one minute , to reset the appliance. ... Whirlpool Dishwashers

Honda gx160 wont pull start with spark plug in.


... Honda Pressure Washers

UNIT TIPPED OVER IN TRUCK OIL IN CYLINDER PULLED PLUG AND REPLACED PLUG NOW WONT START


... Pressure Washers

Just bought a jet usa 7.0HP 3950 PSI pressure washer, put it together and put oil in it and i cant pull the pull start cord out at all?


... Pressure Washers

Briggs and Stratton pressure washer will not start. I have a 6.75 hp pressure washer that is only a year old. when I pull cord it turns over but does not start. I changed plug and checked it, I have spark when pulling. I have 40-50 psi of compression when pulling also. gas was drained and is brand new. it was working fine last time it was used. I have tried starting it without the water line or spray wand hooked up and no difference. After about 10 or 15 pulls, can smell gas when I am trying to


Hello dave, the problem is compression to low,you need 60 to 130 lbs to run engine,check for blown head gasket,or bad rings,or a stuck open valve,hope this helps,, ... Briggs & Stratton Pressure Washers

Won start Was using the pressure washer 1st time this year and started on the second pull. Ran out of gas shut-off also noticed it needed oil. Believe, I put too much oil so, I drained some and added gas. At first, there was no resistant in the pull so waited an hour and tried again. This time the resistant was there on the pull but still would not start; no attempt even to turn over. It's been a couple of days...changed the spark plug although, hardware guy said nothing was wrong with it..still


... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

My lawn mower with a Briggs motor Wont start, has spark fuel is good , the unit is approx 5 years old, but seldom used, worked great last year, drained the fuel, and stored it for the winter.Refueled it and wont start. I can getting started if I pour a little gas down the carb, but naturally it wont run long. I'm thinking needle and seat, any help would be appreciated. Thanks


... Craftsman 2700 PSI Briggs Stratton Powered Pressure Washer

I have a kohler command pro 8.5 on a porter cable pressure washer. Yesterday it started just fine. Today I pulled the start rope and there was no resistance and the engine did not turn over. The pull rope rewound just fine and I tried again with the same result. After several tries it caught just a little near the end of the pull and the engine started. What is the cause of this problem?


... Porter Cable Pressure Washers

Hi. Got a dishwasher from IKEA - Whirlpool DWH B00. It wont run anymore, 2 years old. It just wont start up, it starts to give a beep, and the solution is to press the <|> button for 2 sec, then restart it. But it still wont start. I've cleaned all filters, checked for water on board underneath, and given it some salt - no luck. Any ideas?


... Whirlpool Dishwashers

I started the motor and it ran about 30 seconds and it cut off . I then tried to pull start it and it would not pull easy it pulled hard til i could not pull it anymore.


I get this question a lot, and 9 times out of 10 the reason it because there is pressure in the pump. After the unit shut down did you pull the trigger to release all the pressure from the pump before attempting to restart? When these units have pre ... Honda Pressure Washers

My pull cord to my pressure washer is hard to pull and it's not starting. Why? This all started after I tried to start it without the water on while attempting to start.


Take out the spark plug and trying pulling it , if its still tight then you may have seized your pump ) , put a rag over te spark plug hole as there may be fuel/oil mix in the cylinder , check the oil in the engine , check the oil in the pump ( look ... Pressure Washers

Very Hard to Pull Cord to start engine on Northstar Pressure Washer. When I remove spark-plug it is very easy to pull cord. With plug reinserted it is extremely difficult to pull cord to start engine.


On the Honda motors very hard pull starting with no start ck for broken rocker on exhaust or intake, I've already repaired two with this problem...... ... Northstar Pressure Washer 3000 PSI

I have a 4 year old Maytag MDBH945AWW and the panel lights come on and I can select cycles... but the dishwasher wont start. I tried holding the start cancel button, tried turning the breaker off for a couple of hours, took the inner panel off the door and checked the latch, but its still wont start. Any other suggestions? If it needs a new control panel its probably better to just get a new similar dishwasher for $300, correct?


What you need to do is read for continuity and power across the door latch switch. (2 white wires) AND 2 Black wires Both wires must read continuty at the control panel connectors to the power source terminals for the unit to start. Since the co ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

I have a Whirlpool GU2275XTVY0 when I start the cycle on normal it will run for about 5 minutes then the power button starts flashing and wont run. It drains fine and starts fine just wont finish the cycle.


It might help if the wash arm had started moving when it shut off.\015\012\015\012Unless it is always exactly 5 minutes I would say perhaps the door switch is out of alignment. It might start ok when you engaged at time of closing door bu ... Whirlpool Gold GU2275XTV Builtin Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1063 seconds