Having problems with your Pressure Washers ?

Honda gc160 when I first pull it. It wants to start. Then dies in 1/2 second. I have put a new fuel punp, plug, and coil on it and opened the carb at float. cleaned it there. it will not do anything after the first pull untill 15 min latter, then it does the same thing ?


Answers :

Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Honda gc160 when I first pull it. It wants to start. Then dies in 1/2 second. I have put a new fuel punp, plug, and coil on it and opened the carb at float. cleaned it there. it will not do anything after the first pull untill 15 min latter, then it does the same thing ?


... Pressure Washers

Honda GX 240 on woodsplitter stopped running. Tries to fire a couple of times each pull but dies. Found debris in gas tank. Cleaned out the tank and hose to carb. Cleaned out the sediment cup. Cleaned out the rust and debris from the bottom of the float bowl. sounds like debris in carb jets? Is it worthwhile taking the carb apart and cleaning it, or just order a new carb?


Install a new plug, and make sure your gas mixture is not to rich, And you air cleaner is clean ... Honda 8 HP Engine

8 hp honda on cement mixer starts on first pull but shuts down as if it is running out of gas. I put fresh gas in it and cleaned the filter and bowl of the carb.


If it has a fuel filter. check that. change the spark plugs. ... Honda Pressure Washers

My Kenmore 13743 is 3 years old and was washing perfectly until a couple of months ago. It has become so bad that it won't clean anything on the top rack and barely anything on the bottom rack. In fact, I just pulled a butter knife out of the rack that still had butter on it! Not normal... I do not know how to remove the bottom washer arm to get at the chopper, filter, etc. Please help


Hello,\015\012\015\012Welcome to FixYa,\015\012\015\012You are likely right on, this is very common with these unfortunately. Hopefully this will help.\015\012\015\012**Unplug the unit or turn off the powe ... Kenmore 13743 Staimless Steel Built-in Dishwasher

I have a Generac power washer with briggs and stratten 4.5 Horse. I bought it 7 years ago and stored it. I started for the first time today, it started on the first pull and runs great, but doesn't pump syphon cleaning solution from a mixture in bucket. Why not?


I hope you did have it connected to a water line. I'm also assuming the pressure washer function is working ok. Some times the sypon tubing gets clogged from cleaners drying up and building up in tubing and passageway. Does your gun have a cleaning ... Briggs & Stratton Power Products 1539 Pressure Washer

Asko dishwasher- about 1 year old. Dishes are clean but very wet at the end of cycle. The bottom tub is filled with water (looks clean and warm). The dishwasher is leaking and water on tile kitchen floor. I checked for a float device inside and do not see one. What do you think problem is? How can I check hoses to see if clogged- do I need to pull washer out? Is that hard?


... Asko 24 in. 1895 Built-in Dishwasher

I have a KitchenAid Model KUDP01FLBT5. After I push one of the clean buttons, and the start button and close it, nothing happens. The indicator lights for the buttons come on as you push them. When this first started, you would ahve to open and close the door and re-set the buttons (not sure if that button re-setting had anything to do with it) up to 20 or 30 times, and it would eventually come on. Now it won't anymore. Help!


Hi\015\012\015\012Thanks for using FixYa. To\015\012resolve this you will have to reset the console. Do this by closing the door\015\012and press these buttons in sequence...\015\012\015\012 ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

I have a Siemens SE65560/12, FD 7808 model. This morning water (not many) was still in the machine, and on the display was "I" indicated, or maybe means "1". Now the machine does nothing anymore ... I checked already the rotor of the drainage pump, and also the filters are clean ... after pulling out the plug from the wall socket, and reconnecting the machine, on the display stays the indication "I" or "1". I can't do anything ...what's the problem


I do not know if you been talking to other experts but without knowing how far you went with them if any I may need to start from the beginning these units are sold in Europe and not the US is that true. Second from your post you went t ... Dishwashers

Not Draining I pulled the filter cover off and found some glass and plastic in the filter area,cleaned it out and it still will not drain.I don't know if this plays into the problem or not,but I replaced the old garbage disposer with a new one.The first time I used the dishwasher after installing the garbage disposer is when I started having the draining problem.


If it does not drain, the drain line can be internally obstructed, follow the instuctions on following link :\015\012\015\012The water doesn't drain from the ... Kenmore 24 in. 15689 Built-in Dishwasher

Nasty Smell! After running the dishwasher, there's a pretty foul odor when I first open the door. Is there anything that should be regularly cleaned. I've had the dishwasher for 5 years....?


There is a product at the grocery store in the detergent area that will take care of this ... find it near the dishwasher products. ... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

The dishwasher smells like a greasetrap. where can I pull anything out to clean. drivinh me crazy. Iuse those dishwasher cleaners all the time and doesnt do much


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a LG LDF7810 WW. The bottom rack does not come clean any more. I pulled the sprayer arm and checked as manual suggested. Anything else?


Could be a bad VIRO motor. It moves a valve to change water flow between bottom spray arm and top spay arm about every 2 minutes of the wash cycle. You have to pull the dishwasher and lay it on it's back or side to change it, but you only need a ph ... LG 24 in. LDF7810 Built-in Dishwasher

Won't Drain I've removed and cleaned lower arm and drain in right corner. How hard to remove the upper spray arm? no parts to remove first? What's the float for in the left corner? ted


I think you need to clean the filter under the lower sprayer...I had to do that once and worked like a charm afterwords. ... Maytag MDB7100AWB Dishwasher

The dishwasher cycles down to 1min and then keeps trying to empty. It never does get there though. Water is still in the sump. Emptied this out once and it started ok again. Removed side cleaned out the sticky float switch. This was full of gunk. Noticed rear tank was partially blocked. Is this anything? Which is the outlet solenoid


... Neff 24 in. S5457X0GB Built-in Dishwasher

Frigidare GLD2450RDS0, unit is approximately 5 years old. All of a sudden the water is not draining out of the tub in the bottom. Bailed water out, pulled the glass tap out and cleaned, pulled the lower sprayer out and cleaned, pulled the filter out and cleaned it. Put back together and ran a cycle...still left water in bottom. Help please!


... Frigidaire Dishwashers

I have a Whirlpool DU810SWLQ0 that will not drain. I've pulled the unit out, snaked the drain tube, pulled the motor/pump, and pipe assemblies, and cleaned the food trap, which I also removed. I've run the dishwasher with a bit of bleach, and the water will pump in, get processed by the agitator, and be heated. When the rinse cycle comes, dishes get covered in food, and are never clean. Waste water was being used for a clean rinse. I've run the dishwasher with the drain dangling in a bucket,


Refer the wash system assembly dwg. Check if the ball (item 21) is sitting correctly. If it is out of ali ... Dishwashers

I have two G818SCVi dishwashers both are flashing intake /drain.I removed the drain lines ,both were clean. I took apart the water inlet and pulled the screen.they were clean,also pulled the filter in the machine they are clean


Double check the water pump. It may not be pulling or pushing water. ... Miele Incognito G818SCVi Built-in Dishwasher

Recently bot a home with a GE Profile dishwasher -- only about 4 years old -- it does not get anything clean -- before replacing it I was told that it might just need some "line" cleaning -- anyone know anything about that


Hello,\015\012\015\012Welcome To FixYa.\015\012\015\012Before getting into this too far I have a couple of question`s which will enlighten me in which direction to steer you.\015\012\015\012First, the ... GE Dishwashers

8 year old maytag, clean lime build-up 2 times a year and all the spinning parts look clean and no wear but all of asudden the washer does not clean the dishes very well. Plenty of hot water, soap is dispenced, cleaned screan in bottom, don' really see anything out of place. what could the problem be? Thanks Rick L.


Hi,\012In you case check the heating element first...\012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... \012 ... Maytag Dishwashers

My dishwashing isn't filling properly. I think there is residue on the float "thingy" (located on the bottom right side close to the door) and it doesn't float like it should, so the dishwasher thinks the water level is correct when it isn't. How can I clean it and get rid of the gunk that is keeping the float from floating?.


It appears you already have someone providing solutions on this posting. Unfortunately I am not able to see the responses.\015\012\015\012It mgiht help if you can provide the full model number of the dishasher.\015\012The float shou ... Westinghouse Dishwashers

Have to hand wash dishes before and after dishwasher does not clean anything. Food just stays on dishes and glasses come out bad. Use the rinse and have cleaned it with the cleaning solution several times. Works a little better for a day or 2 after cleaning


Suggest you check the salt level. Also open the door part way through a wash cycle (after only opening a small amouny first) to ensure that water being dispersed around compartment correctly ... Dishwashers

Whirlpool dishwasher float 'assembly' model-DU810SWPQ2


... Dishwashers

Pull my pump first startsthe pressure is good as soon as i pull the trigger the pressure is gone as long as i hold trigger just faucet flow let go of it pressure builds up until i pull trgger , no pre


... Annovi Reverberi RMW2.5G25D

I recently purchased a northstar 4000 psi pressure washer. I had the same series pressure washer for the past 6 years and used a downstream chemical unloader quick connect to pull chemical. I attached it to the pressure washer and it is not pulling. I havent modified anything and I dont want to pull chemical through my machine.


The injector might be worn out or have something inside of the valve causing it not to ****. If you are using a new high pressure hose or a longer hose this may also have an effect over the injector not working. ... Northstar Professional Series Pressure Washer 4000 PSI

Miele G572 is not cleaning dishes correctly, I have pulled all arms off and cleaned, cleaned filters. Powder is not been flushed completely from door. Does the machine require servicing?


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Miele Premier-Plus Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1095 seconds