Having problems with your Pressure Washers ?

Sca petrol pressure washer just stopped. How does the low oil switch work?

\015 Its always taken a few pulls to start, but today it started but as soon as I pulled the hose trigger it cut out. Checked spark, looks OK. Stripped carb and all clean. Doesnt seem to get fuel on the plug though even after many pulls on choke. Not sure how the low oil switch works but because I get a spark I guess its OK, so I'm stuck now.\015

Answers :

Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Sca petrol pressure washer just stopped. How does the low oil switch work?


... Pressure Washers

Hi, I have a Dewalt pressure washer 3100 psi. I want to know why the pressure washer works okay for 1 hour then it stop working completely. the oil is fine, the spark plugs are okay, and when I tried to start it again it does not work. Can you please tell me what could be the problem? This pressure washer is almost brand new I have used it for only like 30 hours for 2 years that I have it. I used it couple times lately but same problem it works for 1 hour then it does not work any. I will


There are two common issues that will cause what you are describing. What you need to do is run the machine until it dies as you are describing. Then pull the spark plug and check for spark. If you do not have spark you have a failing stater. It is v ... Dewalt DPH3100 Gas Pressure Washer

Karcher B402 pressure washer Motor runs as soon as power supply connected, on/off switch does not seem to make a difference and no pressure at outlet? Was working fine, stopped for half an hour, came back and wouldn't work. Thanks Bob


Bob I had this happen to my Karcher, the pressure seals have blown. $Au200 for service and replacement from karcher dealer. tyhey would not sell the parts for a DFY ... Pressure Washers

Craftsman Pressure Washer 2.7 GPM 3000 PSI. Stopped working, found no oil, added oil now washer will not start, can't even pull the cord. Help


... Pressure Washers

Stopped working the pressure washer i have been usingfor the last hour has stopped working water is going into the unit and when switched on the unit apeares to be running however allthough water is comming out of the hose it is not under pressue have tried leavin it for half hour to cool downn but no good


... Pressure Washers

Our craftsmen electric pressure washer stopped working while in use. We have power - red light on gfci and we tested the master switch - has power too. So what can be the problem? One post mentioned a jammed pump switch. What is that and where is it? We used it 2 weeks ago and it worked fine.


The pump switch they spoke of is an internal switch. It is activated by a valve so that when you let go of the trigger, the machine shuts off. This valve is stuck or the switch is bad. Usually the valve is the problem. I would go to Sears and get ... Pressure Washers

I have a Coleman powermate clean machine pressure washer 2500 psi 2.36gpm and has a 6x200 honda 6.5 horse motor. I just bought at a garage sale.It started just fine when I got home and in less that 2 minutes quit. It says the engine will stop automatically when low on oil. what kind of oil should I use and for the pump what kind of oil do you use?


... Coleman Pressure Washer PW0881800

The karcher pressure washer was working one day then just stopped working the next day .Thepower light comes on when i press the on switch but nothing happens .So the power is getting to it but will just not fire up .Please could you advise


... Karcher Pressure Washers

The top drawer of my fisher paykel dishwasher stops during the cycle and shows an icon of a tap with a line threw it (assume that means no or low water pressure). the bottom works fine so I assume water pressure is not the issue; is there a sensor that could be bad? Also, I did switch the controllers between drawers (good instructions on the fisherpaykelparts.net website) but the problem stayed with the drawer, ruling out the controller.


Did it fill with water? could be 1 of your water valves is faulty, or the little filter for the inlet water is blocked. please reply 4 more help. i"m sure i can fix this problem for you. good luck. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I was using my Karcher 350M pressure washer working fine but it just stopped having tripped the power boards circuit breaker. The breaker now trips each time I switch on the washer. There is no smell of burnt motor and the electric did not get wet when last in use. Appreciate any suggestions or tests that can be made. I have a decent multimeter. Thanks.


... Karcher 1750 Psi Elec Pressure Washer

I have a McCulloch FHH20A electric pressure washer. It has stopped working. When I hook it up and hit the "on" switch, it comes on for a 1/2 second then stops. The long wand that hooks to the handle will not come off, I am thinking that it is clogged up somewhere. What can I do to fix it?


You will need to remove the nozzle on the end of the lance and clean the small jet out. ... McCulloch 2000 Psi Electric Pressure Washer Fhh20a

I have a Campbell Hausfeld RBPW1810 pressure washer, It has two detergent tanks. I cann't get either to work. I just purchased the unit in June if this year and this is the frist time I am useing the unit. I followed the instructions (low pressure position on the nozzle) and the detergent came on for two second then stopped (only water then). What am I doing Wrong??? Rich From Alqonquin, Ill


Sometimes thinning the solution will help, but in any case make sure the line from detergent tank to pump is sealed, otherwise it just sucks air. I use a small hose clamp at pump. let us know ... Campbell Hausfeld 1800 PSI Electric Pressure Washer

My Karcher 695 pressure washer work well when initially started. If stopped and restarted the pump runs but the output pressure is very low.


... Karcher Pressure Washers

I have a HDS 950 er915 I have the pressure washer working but can't get the steam cleaner to ingnight the spark is working all the time even when just on pump but it will not inject oil even on full heat setting with burner switch on


The fuel pump is controlled by several things. A flow switch, a thermostat, a pressure switch. All must be working for the heater to work. Also you said inject oil. I hope you mean diesel fuel or kerosene. It won't burn oil. ... Karcher Pressure Washers

I have a Karcher 2,600 PSI 2.3 GPM Gas Pressure Washer G 2600 VHR that I have used once last summer. I have stored the PW in my basement with no fuel in the gas tank. The PW was never exposed to freezing temps. I cannot get the PW to start. I put new fuel into the tank, the oil is good, I drained the carburetor, and the spark plug works (tested it). I pull the cord and the engine doesn't turn. Fuel value is on, choke is pulled, and the starter switch is turned on. System is practically brand new


Hi I have a similar pressure washer from Kartcher and the same scenario as yours I have owned it for about 2 years and noticed that it was getting harder and harder to start with each time I use it which is months. If your pw has a honda engine on i ... Karcher G 2600 VH Gas Pressure Washer

I have a cratsman 675 series pressure washer, Briggs and Stratton motor. It stopped as I was using it. I tried to restart and feels like the motor is ceased. Oil was low as I found out. What to do?


... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

I have a wickes 120 bar pressure washer made by lavorwash model no 186897 120 bar . have used it only once about six months ago . on trying to use it today it has just stopped working, have checked fuse and cleaned filter but cannot get a peep out of it . electrical supply is present and passing through switch , please help


... Pressure Washers

I just bought a used Excell XR2600 pressure washer and it stopped working after the first half hour. It seems like it has not fuel, switch it does. is there a fuel on off valve on the machine somewhere that I can't find? Thanks Ed


... Karcher 2500 PSI Pressure Washer

I have an older Landa Pressure Washer. The burner is not working. Once I get the machine running and water flowing to the pressure washer, with the wand pressed, I flip the burner on switch....and nothing...I have no idea how to work on a pressure washer burner. I have been told it could be the igniter, but I don't know how to fix it if it is. Any help is appreciated.


Check for 12V at the igniter connector with the unit running. If you have 12V and no igniter it may be stuck or bad. Thrun the unit off and read continuity across the DISCONNECTED igniter plug / terminals to the igniter. No resistance = open ignit ... Pressure Washers

Turn water on then actuate wand trigger. Pressure washer leaks when wand trigger is actuated and has very low pressure/flow output. After releasing trigger the pressure cycles on - off at approx 1 second interval. I suspect that the plasstic oulet tube is leaking causing low pressure leak out of bottom when trigger is actuated and causes pressure switch to cycle when the trigger is released. Any Help? This pressure washer is approx 18 months old!


You gave a very close solution yourself for the problem. But other leakages can cause such symtoms.Forexample a leaking head or a leaking chemical inlet. These can be caused because the spill valve (pressure control valve) is stuck. When this valve s ... Karcher PSI Electric Pressure Washer

My Hobby88 pressure washer stopped working, now I


Could be just a faulty capacitor that helps the motor to start. You will find this next to the motor if you remove the top cover. ... Pressure Washers

North star petrol pressure washer. working fine, then no high pressure, checked water feed, water filter , pressure relief valve and gun nosall well work sometimes and keep working, when you release the trigger and try in again the pressure gone again. please help, many thanks, richard


Sounds like the regulator is sticking or is airbound. loosen the water connection and then tighten it back. Could also be that the trigger gun is faulty or needs adjustment. Hope this helped ... Karcher 2500 PSI Pressure Washer

At the beginning the pressure washer was running but there was no power from the nozzle. I stop the gun trigger, remove the nozzle , it works for 1 minute and stop working again Now the washher pressure turns off on its own after 1 minute or less Honda 2400 psi


See attached link:\015\012http://www.wmpcs.com/index.php?main_page=page&id=14\015\012\015\012If you continue to have the problem you m ... Honda Karcher G2400HH-R Pressure Washer

Karcher pressure washer works only with low pressure


The inlet screen orientation is of no consequence. Either way should work fine. Check two things...\015\012\015\0121) Many of the spray nozzles have a high and low setting at the tip of the wand (where the water comes out). See if your no ... Karcher G3025OH Pressure Washer

My Karcher K3.48M pressure washer remains in the low pressure mode even when I return the pressure nozzle to the high pressure position. How can this be corrected. The pump seems to build up the pressure because when I release the handle the pump motor stops. This is a fairly new pump which was purchased in the latter part of last year(2010). Could this have been caused by the detergent I have been using which is an automotive shampoo? Please help I love this washer and for the times that I u


... Karcher PSI Electric Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1512 seconds