Having problems with your Pressure Washers ?

Problems connecting the high pressure hose to wand

\015 I was able to connect it once, but now the clip will not go into place. the machine is less than a week old.\015

Answers :

You need to pull back on the outer collar push into place then release the outer collor
Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Husky pressure washer with a Honda 2600psi engine. Problem is, no water will come from the pressure hose. I connected the water w/out the pressure hose and water flows thru strongly. I then connected the pressure hose w/out the wand and water flowed thru the hose fine. When I connect the wand and pull the trigger, nothing. I have replaced the wand and that was not the problem. Please help.


Check the quick disconnect to the wand these are spring operated and can get stuck ... Pressure Washers

I have a Karcher 330 electric power washer. When connected and set to highest pressure (on variable wand) I get no motor action unless I reduce wand setting, then I get a little boost but not much. If I use high pressure conical wand I get high pressure sometimes, other times motor does not go and no pressure is delivered. I have replaced the high pressure hose.


Just wondering. have you tried it without an attachment to see what kind of pressure you get ... Karcher K2.26 Electric Power Washer

Problems connecting the high pressure hose to wand


You need to pull back on the outer collar push into place then release the outer collor ... Pressure Washers

Hi, I have a Karcher 3.75 jubilee powerwasher, there is water coming out from where the high pressure hose connects to the machine and the unit pulses when idling but works perfectly without drop in water pressure, when trigger on gun is pulled, on closer examination the metal connection on the hose turns, is this the problem or something else. thank you.


... Karcher Pressure Washers

Kenmoore Quiet quard 3 Model #665.74363K1 Serial #FS3502091 The unit will not drain properly. When in drain mode, it will drain slowly when diconnected from the disposal and lowerd to floor, and drains even slower at disposal level, or hooked to disposal. Disposal nipple is clear. I removed the hose and flushed it out with high pressure, found no blockages, hose flows freely and did not fix the problem. The motor is turning and seems to pump water fine, all wands are truning with powerfull spray


... Kenmore Dishwashers

Water is coming from the connection between the high pressure hose and the gun instead of the tip of the wand


There is a seal on the end of the hose fitting ... Pressure Washers

I have an Excell 2500 psi with Briggs & Stratton 6.5 HP engine that starts, builds pressure and maintains high pressure as long as the hose is not connected. But as as soon as I connect the hose, it loses all pressure. Is it the pump?


... Pressure Washers

DuraBuilt 1404. Motor kicks in for two seconds, then quits. High pressure hose blew off and I could barely get it threaded back on. Quick coupler broke so I hooked garden hose up direct. Is lack of quick coupler maybe the problem? Could I be missing a part on high pressure hose that makes it so difficult to thread onto male fitting? Thanks! Bob


... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

I have a Comet BXD 2525 G pressure washer pump which is giving me some problem. (Maybe) I hook the water up to pump and the pressure hose up to the pump, turn on the water and the water sprays out of the water connection at the pump. I check the hose to see if it was clog ok and the next was a the water connection ok. It's like the water is not going int the pump. When i start the pressure up the water come out of gun but no pump running like it should. The next thing i was going to look at i


The water inlet needs a gasket like all hose connections. If its gone the pump may be starving for water. ... Comet Pressure Washers

Assembly plans for karcher 2400 psi pressure i recently had a problem, with my pressure washer. i was cleaning out my hose and took the hose assembly and brass fitting off. run water threw it thought i had cleand it out, put it back together and now when i hooked my water hose back up the water comes out of the despencer instead of the pressure wand. does eny one no what i need to do to revurse this?


... Honda Karcher G2400HH-R Pressure Washer

Karcher k3.575 high pressure quick connect high pressure hose not locking


Clean out the dirt and check the hose support that likes to slides down to the end of the hose ... Karcher K3.68MR Electric Pressure Washer

Cat pump 3200 psi problem- plz help! I hook up the hose and no water will come out of the pump out let with or with out the hose the pressure waser hose hooked up!


... Caterpillar Cat Pump Pressure Washer Pump 3SP30G11

High pressure hose connection blew up. Fix? or buy new?


Yes take it to napa auto parts and they can cut and attach a new end which are for hydraulics. They are crimped on and meant to hold very very high pressure. I used to use a pressure washer everyday for a living and it was a tractor rental/repair sho ... Pressure Washers

Unable to connect high pressure hose to gun base on Karcher 3.99M


You probably need to slide the rubber sheath back a quarter inch or so so that the "C" clip slips between the rubber and the wide part of the brass connector. That is what I had to do. ... Karcher Pressure Washers

Soap feed The soap feed hose on my Karcher 2650 does not suck up the soap into the washer. I pulled off the connector piece that the hose is connected to. I can blow through the hose. There is a little metal finger thing that you can tell pushes up into place when the water pressure is high. It seems like it is supposed to drop down and allow some soap through when the water is running. I found a loose(attached to nothing) gasket, looks like a little donut. It was just free floating in t


I fixed mine works good too, watch my video step by step i put it on youtube ... Karcher G2650HHR Gas Pressure Washer

My Karcher high pressure cleaner K 2.180 is not working. When connected to power and water there is water coming out of the lance but it is similar to the pressure of a garden hose and there is NO noi


... Karcher Pressure Washers

I have a new GE Tall Tube built in - CleanSteel dishwasher, I have tried to turn it on and water ends up on the floor, I have taken off the panel and found a black hose thats causing the problem. I have no idea were the lose end connects up to an I know its a pressure hose...Help Please ?


... GE 24" Tall Tub Built-In Dishwasher - Stainless-Steel

My 1 year old gas powered Husky model HU80432 starts and runs fine but gets no pressure from the wand. Water is running freely through all connections and hoses so there are no obstructions, just no pressure, the water just shoots out in a thin stream for about 3 feet. I stored it inside for the winter so there were no freezing issues. What's wrong?


Lime/calcium build up in the pump.\015\012Pour a large amount of liquid TSP into the fresh water inlet and let it sit for two or three days, the longer the better.\015\012This is how I fixed my no pressure problem.\015\012Works gre ... Pressure Washers

Bosch Exxcel Dishwasher (Enr SMS53E12GB/01 FD 9002) bought in July 2010. Error code 15 and "Check Water Supply" light on at same time. Have checked in-line filter in tap connection and all clear, water pressure OK, no kinks/twists in supply hose. Any help would be greatly appreciated - I'll have to call Customer Service in the end as it's outside of my problem-solving ability, but would like to check whether there's a known reset or fix I can try before I call.


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

Kodiak 4000 Bear, Washer runs smoothly, press trigger and washer begins pulsating jets of water, good pressure, used air hose on washer water line and wand, problem still exists. wash application


... Pressure Washers

Hi, My question involves a:Honda GCV160 5.5Chore Master 2400 psi Model CV-2400=4MHC I have very little use on it. I broke the sprayer hose on it the other day and ordered a new one for this model. I connected my water supply, turned it on, started the machine but have VERY little pressure. What do you feel my problem is and how can I remide it? Thank You! Louie [email protected] Boundary Waters Taxidermy, Ely Mn. 55731218 365 6310e


\015\012put in your garden hose \015\012turn on the water\015\012leave it to run for one min.\015\012kink the garden hoes\015\012connec ... Pressure Washers

When garden hose is connected to the pressure washer no water comes out of the wand, engine is off.


Dear radcongirl,\015\012Try removing the high pressure hose from the machine. Then connect the water hose and see if water comes out of the outlet.( you can also try this by putting on the machine for a few seconds). If water comes out of the ... Honda Maxus Pressure Washer MX5222

I bought a new karcher model no. K3.690 Thurs. Apr. 8th 2010, I tried to start it today Sun. Apr. 11th, when connecting my high pressure hose, to the trigger assembly, it does not lock in, I followed the proper instructions as per the quick start.


... Alfred Karcher K 5.93 M Electric Pressure Washer

I have a Husky 2600 2.3 pressure washer with a Honda motor that is only two years old. When I connect the hose and the sprayer I can shoot water through the sprayer no problem. The second I pull start the engine the water stops. Why would water only come through when the engine isn't running?


... Honda Pressure Washers

Comet BXD2527 worked fine yesteday,no problems. Today, no high pressure. Checked supply water, screen, and hoses. What next?


The water admitance valve is stuck in the high pressure position. The valve blocks further water from entering thus regulating the high pressure. This is usually due to deposits or deteriorated O Rings or both.\015\012\015\012Remove the ... Comet BXD2527 Pressure Washer Pump
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1228 seconds