Having problems with your Pressure Washers ?

Leaking hardie pope watering wand - Pressure Washers


Answers :

Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Leaking hardie pope watering wand - Pressure Washers


... Pressure Washers

Turn water on then actuate wand trigger. Pressure washer leaks when wand trigger is actuated and has very low pressure/flow output. After releasing trigger the pressure cycles on - off at approx 1 second interval. I suspect that the plasstic oulet tube is leaking causing low pressure leak out of bottom when trigger is actuated and causes pressure switch to cycle when the trigger is released. Any Help? This pressure washer is approx 18 months old!


You gave a very close solution yourself for the problem. But other leakages can cause such symtoms.Forexample a leaking head or a leaking chemical inlet. These can be caused because the spill valve (pressure control valve) is stuck. When this valve s ... Karcher PSI Electric Pressure Washer

I have a Karcher K3.48M electric pressure washer which used to shut off when you weren't using the cleaning wand. This no longer happens and there is alot of water running out of the bottom of the unit. (This didn't used ot be the case) I expect a leak somewhere inside the unit, but I'm wondering even more if there is a pressure switch which has failed that cased the leak. In other words, if I find and repair the leak and there is a failed pressure switch, it will likely only break again. I can'


Hi you will have a 8 digit number on a silver plate on the machine with a number like 1.141-470.0\015\012Then go to www.karcher.com then on the left click on Europe, then you ... Karcher PSI Electric Pressure Washer

I have a Husky pressure washer with a Honda 2600psi engine. Problem is, no water will come from the pressure hose. I connected the water w/out the pressure hose and water flows thru strongly. I then connected the pressure hose w/out the wand and water flowed thru the hose fine. When I connect the wand and pull the trigger, nothing. I have replaced the wand and that was not the problem. Please help.


Check the quick disconnect to the wand these are spring operated and can get stuck ... Pressure Washers

Hi ..I have an Excell gas pressure washer model no. Exwgv2121-3 with Faip 2100 psi 2 gpm vertical shaft pump..the problem is that there is water leaking from every weep hole at the bottom of the pump when running. Oddly enough,the pump still puts out significant pressure but less than it should due to the leaking water. What is the most likely cause of this?..is it the high pressure water seal(s)? If so,how do I repair it?


... Pressure Washers

I have a Honda gc160 5.0 pressure washer. All fluids are fresh. Water is hooked up with plenty of pressure but the water pressure is up and down then goes completely out. No water will come out of the wand? Please advise. Thank you.


Needs new pump ... Karcher 2500 PSI Pressure Washer

Assembly plans for karcher 2400 psi pressure i recently had a problem, with my pressure washer. i was cleaning out my hose and took the hose assembly and brass fitting off. run water threw it thought i had cleand it out, put it back together and now when i hooked my water hose back up the water comes out of the despencer instead of the pressure wand. does eny one no what i need to do to revurse this?


... Honda Karcher G2400HH-R Pressure Washer

Smeg DWF612WH dishwasher has developed a leak. Water comes out of the rectangular hole on the side of the water softner used to mount what looks like a level or pressure switch. A few seconds after the fill valve opens water leaks out, not a lot just a small trickle. After the washer has filled and goes ito its cycle, it does not leak again. Over the past weeks the problem has got progressively worse.


... Smeg 24 in. DWF612WH Free-standing Dishwasher

I have an older Landa Pressure Washer. The burner is not working. Once I get the machine running and water flowing to the pressure washer, with the wand pressed, I flip the burner on switch....and nothing...I have no idea how to work on a pressure washer burner. I have been told it could be the igniter, but I don't know how to fix it if it is. Any help is appreciated.


Check for 12V at the igniter connector with the unit running. If you have 12V and no igniter it may be stuck or bad. Thrun the unit off and read continuity across the DISCONNECTED igniter plug / terminals to the igniter. No resistance = open ignit ... Pressure Washers

Karcher K 3.65 Jubilee Pressure Washer - water pulses,low pressure and leaks under machine


... Karcher Pressure Washers

I have a karcher 4.6 pressure washer that developed the usual fault.... drop in pressure and leaking from the cylinder head. I have replaced the cylinder head and the attached control chamber. The pressure is now good again and the leak is fixed. Unfortunately now when the trigger on the lance is released the the machine does not switch off automatically. I have bled the machine by letting water run through it


... Karcher Pressure Washers

Kodiak 4000 Bear, Washer runs smoothly, press trigger and washer begins pulsating jets of water, good pressure, used air hose on washer water line and wand, problem still exists. wash application


... Pressure Washers

Troy Bilt pressure washer model 020209 will not build pressure-have checked all screens and intake in pressure hose and garden hose from house to pump. water leaks at gun handle- took it apart and oiled piston- was ''grabby'' but now snappy but still leaks. Engine starts fine and runs fine. Please help.


A leaking gun will kill all the pressure. You may need to repair or replace the gun ... Briggs & Stratton Pressure Washers

I have a Northstar pressure washer powered by a honda GC160 engine. The last time i used it, water leaks from the bottom of the unit, whether it is running or not. When running, the pressure is fine. I have felt underneath and it appears that the water is coming from the second opening from the rear. Is there a pressure relief valve there. I have a manual but cannot find any descriptors for underneath the motor.


This is a piston seal issue. You can get a kit to rebuild the pump. ... Comet AXD 3020 G Pressure Washer Pump

My pressure washer leaks water out the back form some kind of valve that has a hole in it. the pressure washer will flow pressure but not as much as it did.


... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

I have a zr2700 pressure washer. As soon as it is started, water pumps through very forcefully. Pressing and releasing the triger on the wand does not control the water. Do I need a new wand or is there a problem with the pump


... Pressure Washers

Pressure washer leaking water - Craftsman Pressure Washers


... Craftsman Pressure Washers

My Powercraft 9686 pressure washer has always been stored in my garden shed. It is 4 years old and when I used it last September the power washer had lost considerable pressure, as it was leaking water. Can I fix it for a reasonable price? Thank You. John O D


Put some silicon spray in inlet/outlet then reattach hoses then run it will proform after a while do this everytime you store it pryer to sroring away........... ... Craftsman 2700 PSI Briggs Stratton Powered Pressure Washer

The water fills slow and rinse has very little water pressure, I have pressure as far up as the celenoid and cleaned the washer wands&nozzles. there's an elbow with a fitting in it and 2 wires.can you tell me what this is and or give advice to a solution


... Hobart AM14C-155 Dishwasher

Hozelock pressure washer is leaking water - Pressure Washers


... Pressure Washers

Karcher k3.68m leaks from the pump area. If I turn it on without holding the trigger down on the wand it will not blow pressurized water. If the motor is idle and the water is turned on then it leaks a lot from the pump area. What part should I replace?


... Karcher PSI Electric Pressure Washer

My pressure washer doesn't start/work when I attach my wand to the trigger. It works fine when I take it off, but there is no pressure, just normal water coming out. I'm thinking I may need a replacement wand?


... McCulloch FH160G Pressure Washer

Husky 500 2200 psi. starts and runs ok, but no pressure through the wand. hooked up garden hose to power washer turned water on and it comes through the hose ok, but start up and put wand on and no pressure.


... Pressure Washers

Two problems please: craftsman 2150psi briggs and stratton engine washer, will not start when hot. and secondly, i was washing with regular pressure, then noticed a pressure drop at the nozzle, then the unit shut down. no water leaks at the manifold. water supply was strong. any ideas?


Nozzle dirty, clean out with small diameter wire. ... Pressure Washers

Karcher K6.50 Water coming from body of washer resulting in loss of pressure. Leak slows down when washer is used - ie water is coming out of jet


... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1145 seconds