Having problems with your Pressure Washers ?

How do I remove the spray gun on a husky power washer 1750?

\015 I can't figure out how to remove spray gun from hose. What's the trick?\015

Answers :

Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I remove the spray gun on a husky power washer 1750?


... Pressure Washers

Campbell Hausfield Pressure washer model 1549. After a few years of storage, I cannot prevent the powerful spray leaking from the connection between the Gun and the Lance. I replaced the O-Ring, and tried other means unsuccessfully. Spray from the joint is almost as powerful as spray from the lance nozzle. The Briggs and Stratton engine has been cleaned and operates well. The pump operates well. But the lance connection refuses to seal.


Hello,Most likely, the housing has split and seal is not being made. There is a chance that the hose is leaking where the fitting is crimped on (my experience, but different pressure washer). Are you able to see a leak when turned off b ... Campbell Hausfeld Pressure Washers

I have a handy power HPGW 1500 pressure washer and when its used the water sprayes out of the gun around the handle part as well as the nozzel is it possible to purchase a new gun and connection to the machine


... HP Pressure Washers

On my John Deere power washer 3300 the gun sprays at full power even when trigger is not being pulled what could be wrong?


... Pressure Washers

Took gun assembly apart on Husky 1750 Power Washer. Spring fell out, where does it go? Looking for gun assembly schematic.


... Pressure Washers

Why will water not flow through hose into the spray gun with the washer not started as well I started the power washer and the water still does not come out.


... Craftsman 2500 PSI Briggs & Stratton Powered Pressure Washer

I have a weekender h1610 power washer i took the spray gun apart and cannot remember where this little spring goes


Email me pictures of the spring and the part that it came from and i will try to help u ,,, [email protected] ... Pressure Washers

Husky power washer does not spray cleaner just water.


Did you adjusted the sprayer? Only on low pressure will spray cleaner, if still does not spray, the problem is at the pump ... Pressure Washers

At the beginning the pressure washer was running but there was no power from the nozzle. I stop the gun trigger, remove the nozzle , it works for 1 minute and stop working again Now the washher pressure turns off on its own after 1 minute or less Honda 2400 psi


See attached link:\015\012http://www.wmpcs.com/index.php?main_page=page&id=14\015\012\015\012If you continue to have the problem you m ... Honda Karcher G2400HH-R Pressure Washer

I have a Husky 2600 PSI power washer with the Honda GCV160 engine that I can't get to start. It was okay when I purchased it from Home Depot last spring but now I've tried putting new gas in it, spraying carb cleaner, new spark plug, and it still won't start. I only ran it for about 30 minutes when I first purchased it. The guy at the service desk at Home Depot told me that the water hose should be attached and turned on while trying to start. Is this true or would this be starting the motor und


You can eliminate the motor by unbolting the pump from it and then if it will start the problem is with the pump or the unloading valve.If it does not start with the pump removed then you check for spark and get the carb cleaned or have a kit put in ... Karcher 2500 PSI Pressure Washer

Husky HU 80522 pressure washer - some pressure to the spray gun. water coming from the pump goes straight to the sifon hose used for detergent. Can this line be clamped of if not used?


... Pressure Washers

GU980 dishwasher I have a buzzing sound when the washer is in drain mode. The manual indicates there might be something in the Power Clean Filter, and that it will go away when the object grinds up. I called Whirpool, and they said the same, and to run for 2-3 cycles to make go away. 2-3 cyles later, noise is still there. I noticed a nub off the rack that looks like an end peice of metal broke off from rust. My guess is it's stuck in the PCF, and will not grind up. I removed the nut, lower spray


The nut holding the inpeller has to come off it is probally frozen\015\012if it snaps off then the pump assy willl have to be replaced or at least the motor, you need to get below the impeller to see what is down there though, or let it run as ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Husky HU 80522 pressure washer - some pressure to the spray gun. water coming from the pump goes straight to the sifon hose used for detergent. Can this line be clamped of if not used?


This unit has a Faip pump on the unit, no water should come out the chemical injector. The chemical injector can be closed off with no problem by installing a plug where the chemical injector hose bard is currently located.You can also replace th ... Pressure Washers

The disk washer doesn't drain at the end of the rinse cycle. There is a humming sound but no water is forced through the hose to the sink/garbabe disposal. At the end of the wash, there is a large amount of dirty water in the bottom of the washer. I removed the spray arms, the spray arm holder and the screen and then removed the water, and found a couple of pieces of plastic. But I don't see how I can remove additional parts from the washer bottom. What could the problem be? Is there a fi


Is the dishwasher drain hooked to the garbage disposer? If so is it new? If so did you knockout the plug in the disposer? If so then you either have something clogging the drain or pump. Or the pump motor is bad. ... Dishwashers

I have a washer model 1805 (1800 PSI). Everything works but there is always leaking of water (sprays) when I use it. The leak is not from where the water hose connects to the washer, but where the black piece attached to the hose is connected to the body of the washer. I can still do a decent job of power washing, but am wondering if the leaking of water is reducing the power of the washer.


Yes, leaking water will reduce the pressure. Sounds like you need to replace the O-Ring inside the connections on the pump. This is where the pressure hose connects to the pump. If you look carefully inside that connection you will see an O-Ring. Use ... Campbell Hausfeld PW1805 1800 PSI 15 GPM Pressure Washer

Husky power washer 1650psi axle replacement


... Pressure Washers

I have a Craftsman power washer model 580 752020. When I start it up, turn on the switch the electric motor runs fine until I either close the trigger to the spray nozzle or press the trigger for power spray. The electric motor just shuts down, if I take my finger off the pressure and let the water run with no presssure the motor runs fine. My question is this. Is the capasitator on the electric motor the probable cause and is there a way to check out the capasitator to see if it is malfuncti


I doubt that it has anything to do with the capacitor on the motor. i think you are having a problem with the actual Motor Drive circuitry. What is happening is when you close the switch, this tells the Motor to "Ramp Up" to pump the water out, what ... Craftsman Pressure Washers

Karcher max 2700 psi 6.6 gpm 140F spray gun - Oregon 37-068 Pressure Washer Spray Gun With 12-Inch Lance Medium Duty 2,700 Max PSI 6.6 GPM 140-Degree F Max 1/4-Inch Male Inle


... Oregon 37-068 Pressure Washer Spray Gun With 12-Inch Lance Medium Duty 2,700 Max PSI 6.6 GPM 140-Degree F Max 1/4-Inch Male Inle

Power washer starts no problem but when turned on and activating the trigger on the pressure washer gun, water no longer comes out. The gun itself was replaced not long ago. What could be the cause?


The tip could be plugged up ... Honda Pressure Washers

I have a McCulloch FH160B power washer and it no longer builds up pressure. I haven't used this very much at all. I tore it apart and cleaned everything I could find. When i pull the trigger for the spray nozzle, I get line water pressure. When I release the trigger, the power washer sounds like it starts to build up pressure. When this was working correctly, the pump would shut off when the trigger was released. Any suggestions?


... McCulloch Pressure Washers

Husky power washer 2000 is not getting power - Pressure Washers


... Pressure Washers

I have a Honda xr2600 power washer. When I tried using it, water was squirting from the top of the gun. I took it apart to find that there are o-rings on top of some kind of washer---looks like a lock washer but it's made of cardboard??? Two of these washers were broken. I can get the o-rings but I can't seem to find the washers. I tried getting the manual for this model on line with no luck. Any assistance will be greatly appreciated.


The washers that you describe are made of teflon and are split to facilitate installation and/or allow expansion as they wear. These washers are actually seals and at times are used together with orings to seal high pressure. You should ... Honda Pressure Washers

1600 psi durabuilt power washer, hand nozzle, gun, leaks water.


... Pressure Washers

Karcher 2650 power washer Honda GC190; how to remove flywheel


... Karcher 2500 PSI Pressure Washer

Karcher 2650 power washer Honda GC190; how to remove flywheel


... Karcher 2500 PSI Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1235 seconds