Having problems with your Pressure Washers ?

Troy-bilt model 01903 pressure washer stalls under load

\015 Engine runs fine but engine dies after 2-3 min of holding trigger open. will start right back up, engine will continue to run fine but engine will now die after 20- 30 sec of holding trigger open. will start right back up and so on.\015

Answers :

Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Troy-bilt model 01903 pressure washer stalls under load


... Pressure Washers

Troy bilt 2600psi 2.3gpm model 160 pressure washer, I hooked everything up like normal, It cranked up fine, when I pulled the trigger on the gun it stalled. When I try to crank it back up the cord wont even pull like its stuck any suggestions would really help me tks..


This sounds like the pump has dead headed. I.e. the unloader valve is sticking. Unhooking all of the hoses should eventually allow everything to free up. Once it is free what you should do is add about 3 ounces of oil into the water inlet connecti ... Pressure Washers

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started. I have the same problem. Water flows thru the pump when not running, but no flow or goes in by-pass mode when I start the pump. The pump being Troy Bilt Model 020296-01. I replaced unloader valve even. Anything else I can do?


You replaced the unloaded valve. Are you positive you have the unloader screwed to pressure and not turned the opposite way? You will have no pressure if it is adjusted wrong. One other thing I have encountered is that the unloader has a ball bearing ... Pressure Washers

Troy-Bilt pressure washer does not provide pressure


... Briggs & Stratton Pressure Washers

Troy Bilt pressure washer model 020209 will not build pressure-have checked all screens and intake in pressure hose and garden hose from house to pump. water leaks at gun handle- took it apart and oiled piston- was ''grabby'' but now snappy but still leaks. Engine starts fine and runs fine. Please help.


A leaking gun will kill all the pressure. You may need to repair or replace the gun ... Briggs & Stratton Pressure Washers

Hi I have a Troy-Bilt Pressure washer 2200 psi model 20292. I've used it only 4 or 5 times. It ran great for an hour today then it lost pressure. Seems like the pump is not working. The engine runs fine but no pressure. The water runs through the nozzel and I blew air in the lines to make sure there is no blockage and found no blockage even in the pump lines. Any ideas. Tom


... Briggs & Stratton Gas Pressure Washer 20244

Troy Bilt Pressure Washer Model 01902 Leaking Gas from Air Filter


Try banging lightly on carberator with block of wood or something to free up float and valve!!!! ... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

Troy Bilt pressure washer model 020489 has very low spraying pressure. How do I repair the pump?


... Pressure Washers

My Troy Bilt pressure washer (Model: 020296-01) idle is up and down. When I engage the trigger I get pressure for a second and that's it. If I squeeze the trigger a second later I get the same thing and so on. Is it just the idle that needs to be adjusted or something else?


... Briggs & Stratton Pressure Washers

Troy Bilt pressure washer model 020209 has very low spraying pressure. How do I repair the pump?


You are going to need a pump seal kit or they may call it a rebuild kit but this sort of thing happens often and you should not have any trouble getting the parts you need with the kit should come a exploded view diagram but request one just to make ... Pressure Washers

How to adjust the pressure on a troy-bilt pressure washer model# 020242


... Pressure Washers

Pressure Washer I have a Porter Cable pressure model no.PCH2401.It works fine for 5 minutes,then I can hear the motor loading down and then it stalls out. I tried to start it and it was very hard to pull on. disconnected the water supply and if was very easy to pull and started right up. I noticed the pump was very hot.This unit has a thermal relief valve on it,shouldn't it have released when it gets to a certain temperature .I was thinking maybe this is why it might be shutting the motor


Any leaks from connection at pump to gun and wand assembly if so the valve is detecting leakage and open up again without u squeezing trigger it builds up in the head.if your trigger gun is leaking internally then you will need to replace the gun thi ... Pressure Washers

Engine manual for a troy-bilt pressures washer 020242 model


... Pressure Washers

The pump leaks on my troy bilt pressure washer model 020344


... Pressure Washers

Troy-bilt 4.5hp pressure washer model 020245 fuel will not flow, stops after starting


... Troy-Bilt 020528 Gas Pressure Washer

Need a manual for a troy bilt pressure washer model 20789


Http://www.ppe-pressure-washer-parts.com/files/1961581/uploaded/020488%20man.pdf This is for the Briggs and Stratton, b ... Troy-Bilt XP 3000 PSI 2.7 GPM Gas Pressure Washer 020489

Need owners manual troy bilt model 020381 - Briggs & Stratton Prosumer 20324 Gas Pressure Washer


... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Troy bilt pressure washer deadheaded - Troy-Bilt 020528 Gas Pressure Washer


... Troy-Bilt 020528 Gas Pressure Washer

My Craftsman model 580.752300 high pressure washer, leaks around the pump and when running and not spraying from the wand the engine is under load and at idle will stall wandmanagemylife com sears


... Pressure Washers

Assembly of Check ball & Spring for Troy Bilt Pressure Washer Model 020241- 2600 PSI?


... Pressure Washers

I have a Troy Built Pressure Washer Model # 01903. It has snapped a bolt off in the pump head area and is leaking H2O. What is the part number of the repair kit for this problem and where can I order it??


... Pressure Washers

I have a Troy Built Pressure Washer Model # 01903. It has snapped a bolt off in the pump head area and is leaking H2O. What is the part number of the repair kit for this problem and where can I order it??


... Pressure Washers

Troy bilt 01903 no water - Pressure Washers


... Pressure Washers

Troy bilt pressure washer will not build or reach high pressure


Check the non-return valves in the pump block. if these are damaged or dirty you pressure will be greatly reduced. they are located behind the 3 lage brass hexagonal caps.\015\012\015\012I hope this helps ... Karcher 2500 PSI Pressure Washer

Bad idle troy bilt pressure washer


... Briggs & Stratton Gas Pressure Washer 20244
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1175 seconds