Having problems with your Pressure Washers ?

Task force 1600 washer will not run due to valve at washer end


Answers :

Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Task force 1600 washer will not run due to valve at washer end


... Pressure Washers

Champion dishwasher we have a champion freestanding dishwasher at my church. after the cycle is completed, the pressure guage behind the washer still shows 25-30 and it contnues to spray water. not forced by the motor, but more like a stuck open fill valve. if i turn off the water and run it, then turn the water back on, the valve is closed and does not let water freely in. butif i run it with the water on, it will continue to spray in freely after the cycle light goes out and you open the door.


If you turn the unit off from the circuit breaker will the water still run?if so the guts inside the solenoid valve are worn.you can call champion and get a kit to replace the worn parts and its not difficult to do.hope this helps. ... Dishwashers

I have a HD 2701 DR pressure washer that starts and runs fine and usually works fine the "first" time but if you let go of the trigger and then try to use it again you just get a trickle out of the end of the wand. Usually if you hold the thing open for a while it will kick in (sometimes it takes forever...). Any ideas? It sounds like some of the "unloader valve" problems are similar but I do not see an "unloader valve" in the parts lists for the 2701...


... Karcher G 3050 OHR Gas Pressure Washer

The disk washer doesn't drain at the end of the rinse cycle. There is a humming sound but no water is forced through the hose to the sink/garbabe disposal. At the end of the wash, there is a large amount of dirty water in the bottom of the washer. I removed the spray arms, the spray arm holder and the screen and then removed the water, and found a couple of pieces of plastic. But I don't see how I can remove additional parts from the washer bottom. What could the problem be? Is there a fi


Is the dishwasher drain hooked to the garbage disposer? If so is it new? If so did you knockout the plug in the disposer? If so then you either have something clogging the drain or pump. Or the pump motor is bad. ... Dishwashers

My G832SC is not draining at the end of the cycle. It runs the entire cycle, and the dishes appear to be clean. The soap dispenser has opened and the dishes are rinsed. However, the dry cycle doesn't run because the machine doesn't drain at the end. The intake/drain light is flashing. If I reset the machine and start a new cycle, it will perform an initial drain and the water level does go down. We checked the tri-filter and the valve pump thing, rinsed both. Checked the hose under the sink. We


... Miele Slimline G832SCi Built-in Dishwasher

Re: Creaftsman 2700 psi washer, model 580.752100 - I cannot use the detergent cleaning tank. The pump forces water into the tank, and it overflows onto the ground. If I try using the washer with the detergent shut-off value in the off position, the water pressue forces the valve completely out of the housing. Is there a simply fix for this or time for a $ervice call? sw


... Craftsman 2700 Max Psi Pressure Washer 23 Max Gpm

Hello I have a Maytag Quiet Series 300 dishwasher model #MDBH955AWW that is making a lot of noise. I saw an exchange on this site where the expert suggested filling the washer to just above the heating element, running it, and seeing if that solved the problem. I tried that and it solved the problem. I believe the expert said this indicates the fill valve needs to be replaced. Can you tell me which valve I need and advise me on how to change the valve? The manuals I have (Use & Care Guide and In


Http://sites.google.com/site/cwyffimsbffoe/maytag-dishwasher-parts-manual- ... Maytag Dishwashers

How to fix an oil leak in my Task Force 2000 psi Pressure Washer


... Pressure Washers

My Bosch integrated dishwasher(model SGV56A03 GB/12) runs through the cycle but doesn't stop at the end of the cycle. It continues to heat water and it sounds like the motor is running even though the time indicator shows 0 minutes. I have to manually switch it off. Any ideas before I call out an engineer. I have checked all the filters etc included in the troubleshooter info anf there are no blockages.


... Bosch Dishwashers

My dishwasher is a Fridigdaire FDB510LCS1, approximately five years old. The timer/knob stops advancing at about 7 o'clock, somewhere in the wash cycle. But the washer keeps running. I marked the place where it stops and, on additional tests, it stops in exactly the same place. I can advance the knob slightly past this location and the washer continues through to the end of the cycle.


Hi\015\012\015\012This is due to a faulty timer on your dishwasher. You would need to replace it to resolve this issue. You can buy the timer for your dishwasher from this link---\015\012\015\012 ... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

After cycle completed, opened door and found water did not drain. i removed the screen at the bottom and used wetvac to **** all the water out. i was also able to hear suction from hose to sink P trap. i'm confident there is no blockage. i attempted to run again only to find out the pump was running but, no water was filling the machine. Yes! the valves are open! two different issues? one other thing; due to the no thought behind this, the name plate was stuck to the inner part of the door whi


Possible that the drain pump needs a closer look , clean and check if the pump is working. If there is voltage to the pump during the drian then the pump is faulty.\012The second issue if the inlet chocking , check the inlet filter , check the ... Bosch SHU9915UC Dishwasher

Kenmore dishwasher. The upper rack is not getting clean. Even very light residue remains. And, detergent is left in door at end of cycle. The bottom is filling up, so I don't think it's the intake valve. Also, all the blade openings appear clear. I am noticing that hot water is not filling the dishwasher when I first run the cycle. Even if I have hot water running in the sink, the dishwasher fills with cold or warm water. So, I think this is the problem. What should I do? Thank you in advance!


I find it odd that the dishwasher is filling with cold water if the water is hot at the sink. It sounds like the dishwasher is connected to the cold water line rather than the hot. Check under your sink; if you've got standard plumbing, the dishwas ... Dishwashers

I have an Ariston LS245 dishwasher, have just had the pump replaced, as it had shorted out, due to water in the bottom tray where the water detection float is, also a new drain hose fitted. Have just run a wash and after running a while, presumably to the end of the rinse, wash and dry cycle, then one of the cycle phase lights, the one for 'soak' blinks constantly. I switched the machine off and had a look to see if a wash had been done, the dishes look clean. In the book it says that if one


... Ariston Technologies Dishwashers

I have a Frigidaire Dishwasher, model #FDB635rfs It is not that old, but appears to have quit working. It sounds like it runs the water gets pushed in by the tube on the side but goes straight to the bottom of the washer. It looks like the spray arms are not spinning. Water is not circulating. Element still heats up. Detergent just runs down the inside of the door and doesn't dissolve since water is not circulating through arms. I have just replaced the water inlet valve and it did not hel


Don't know about yours but many of the rotating spray-heads are turned only by waterpressure, not a separate motor.\015\012The rotator is normally pretty loose and should turn willingly by hand; if it seems stiff and your water pressure is normally l ... LG LDF6810 Built-in Dishwasher

I have a Whirlpool ADP6515. It's been working fine for about 2 years now but recently cycles are not completing properly, it can run for 30-40 minutes depending upon cycle. The start light is flashing a 4 times repeatedly, I think this happens when it moves from a wash to a pump cycle but not sure. We have to hold down the start button to force it to go to the end of the cycle and the the lights stop. If we do that we can then use the dishwasher the next time, but only after we force it to go to


While replacing the console board, the replacement should be of same version. The boards are using programmable IC. Hence matching the software version is a must. Only the manufacturer or his authorized provider can help regarding t ... Whirlpool Gold 24 in BuiltIn Dishwasher w Adaptive Wash Cycle 24 in Builtin Dishwasher

I have a kenmore Ultra Wash Dishwasher, Model 15825691. We were recently hit by lighting. Once hit, the dishwasher started up. Since then, all cycles work, however, at the end of any cycle, the dishwasher continues to run and fill the bottom of the washer up to about two inches and then cuts off, so when we open the washer, there is approx 2 inches of water inside no matter what. I have pressed the "Cancel/Drain" button, in which drains the water after two minutes, but when that is finished, the


There must be a problem wit the fill valve. Check which valve the water enters. Check first the wiring to the valve of the water inlet or where the water comes out to fill the washer. Check for physical evidence of damage on the solenoid (or contr ... Kenmore 24 in. 16539 Built-in Dishwasher

Karcher 3.86M Electric pressure washer. Plugged it into outlet. Unit started running. turned it to off position. Attached hose. Turned on water valve. Turned on switch. Squeezed trigger. Nothing happened. Will not run. Ciruit breaker was reset.


... Karcher PSI Electric Pressure Washer

I have same problem with Chicago Electric # 47761 electric pressure washer as Aug 10 2010 writer had w/ Karcher 2500. Runs briefly then stops. Pressure is trapped in hose. I cleaned hose disassembled & greased valve in handle. No improvement. Problem appears to be premature wear of trigger cam in handle - both are plastic. Valve body is rigid nylon. Any thoughts??


... Pressure Washers

I have a Bosch dish washer model SHX 43 M 0 ZUC / 48 FD 8709 00169 The dish washer is about 1 1/4 years old and was installed by a plumber as part of a Home Depot kitchen remodel. The problem is draining. The quick wash does not drain at the end of the wash. The regular wash sometimes drain and sometimes does not. The auto wash does drain. The lack of draining does not cause problems with the regular wash cycle. I checked the drain hose re the instruction manual and it is correctly installed.


Usually a brush with a flexible shaft will do the trick...\015\012\015\012Like this venturi tube cleaner (available where gas grills are sold)\015\012\015\012 ... Bosch Dishwashers

Kew power washer,model Alto Force E. Will run for about ten minutes, then stop, often for days. Appears to run on two settings - occasionally gives bursts of real power, then reverts to adequate. Stops shortly after wards


... Pressure Washers

2-yr old troy-bilt pressure washer with honda gcv160 engine. seems to run well, but when trigger is pulled get full pressure for less than 5 seconds before reducing to house water pressure. when left running, looks a black plastic pressure relief valve starts blasting hot water. appreciate whatever insight you can give. Thx


It sounds like an air lock. Try this: With the machine off, connect the hose to the washer and let it run for several minutes to get all of the air out of the hose, and to purge any air out of the pump. Shut off the water, and connect the high pre ... Briggs & Stratton Pressure Washers

Bosch SHU43C My Bosch SHU43C is stuck with the drain pump running. I ran the self-test and it gave me the fault code 4 wich indicates a filling fault. The washer is empty and all wash cycles display the correct number of minutes for the cycle. It counts down to 0, but the pump continues to run. Does this indicate a stuck float, or is the problem with the control board? Where is the float located? Are diagrams/pictures available on-line anywhere? I've done some searching, but haven't found any. R


My SHU43C is just over 3 years old. I had a similar problem recently. First, there were a few floods. Then, the Bosch only drained non-stop. Even when I used the Cancel Drain buttons the drain pump would run without stopping. When I ... Bosch 24 in. SHU43 Built-in Dishwasher

Frigidaire dishwasher won't end cycle - will run on and on for hours. Sometimes it cycles through, usually it just endlessly washes and rinses. I have to CANCEL the cycle, which causes the dishwasher to empty and run a few RINSE ONLY cycles (which are consistent, cycle time wise) to rinse the soap off of the dishes. Also, the door for the soap seems to stick - how long into the cycle before the soap door should open? Also, does opening the washer during it's cycle (to add more dishes) change or


I would say the resettable thermostat has failed. There is a thermostat which senses the water temperature, and when it fails, it causes the dishwasher to run constant. Replace the thermostat underneath the dishwasher and that should cure problem. P ... Frigidaire 24 in. FDBB540 Built-in Dishwasher

Hotpoint HDA3400g dishwasher is not running. I have checked to make sure it has power. Took the washer apart, checked that it had power through the door switch to the timer control, all is well. Still not running or getting water into the dishwasher. Any ideas besides replacing the water inlet valve? Will this dishwasher cycle through if it does not have water?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check for the following if your dishwasher\015\012is not working-- ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

Bought suction hose for karcher in order to use water from bucket. Have attached hose but there is no water being sucked from the bucket . One side of hose attached to washer the other dropped in bucket is this right? The end in the bucket has no suction, and a depressable valve that seems to be impeding the water suction. Do I remove this valve ?


... Karcher 26408500 Pressure Washer 25Foot ExtensionReplacement Hose
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.3004 seconds