Having problems with your Pressure Washers ?

Does anyone no if u need more preassure on the turbo lance on a lavor 160 power washer all off the other ones work perfect i bought at lidl the adjustable lance works fine and so does the brush just not the turbo lance if anyone can help i would be very grateful


Answers :

Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Does anyone no if u need more preassure on the turbo lance on a lavor 160 power washer all off the other ones work perfect i bought at lidl the adjustable lance works fine and so does the brush just not the turbo lance if anyone can help i would be very grateful


... Pressure Washers

Could someone please help me i have a lavor 160 superwash and every lance works except when i put the turbo lance on i get full pressure for a few seconds then goes low then high etc etc it has 2 be something simple so please anybody all advise needed thanks


... Honda Karcher G2400HH-R Pressure Washer

Waterintake stops after approx. 35 sec.waterlevel is to low,detergent compartement will not open because of low waterlevel and also water will not heat, because heating element is not covered with water. If I put water in by hand to get the waterlevel above heatingelement everything is fine. Dishwasher has been working without any problems till approx. 18 mths ago. Have also adjusted waterintake time as described in manual by taking off dial knob and adjusted with small flat skrewdriver, but not


The machine fills by time only as you have already determined. The intake screen on the water valve is probably plugged up and cleaning it should solve your problem. You will have to turn off the supply to the dishwasher and disconnect the water feed ... Dishwashers

Dishwasher zdt 6053 Heating element not working......sometimes!!!! tried all three cicles nothing, heating element not working then its fine again for a couple of washes ????? anyone ever come across this problem, faulty thermostat ,faulty heating element,gremlin in the circuit board?????


... Zanussi 23 in. ZDT6252 Built-in Dishwasher

I have some problems with a Whirlpool DWF 406 dishwasher: The other day, my wife complained about it not finishing a program (just stopped and started bleeping). I saw a post at this forum where it said to clean out the black grid down my the sump. I did that, and then the dishwasher worked fine a couple of times. Today when I got home from work, the machine just bleeped at me and and the green LED light by the start button flashed 9 times over and over again. Does anyone know what those 9 flash


We have the same problem. The dishwasher is 10 years old. In one of the German forums they said that usually it's because the sieve ahead of the membrane has a fine layer of sludge and the pump cannot pump out the dirty waste water. They said that yo ... Whirlpool Dishwashers

My dishwasher is a swan sdw7030w, water is going in and out the machine but no water is getting through to man part wher dishes are, am putting it on and it's jumping from my choosen cycle to economy while beeping, the salt light and starish looking 1 are both on as well, can anyone help me? It was working fine n old house, could it possibly be my water pressure as I can't think of anything else as a woman. Please help me.


... Dishwashers

Karcher 520m problemswith turbo lance not working


... Karcher K2.26 Electric Power Washer

Anyone have experience with a Fisher Paykel double draw dishwasher (model DD24) getting stuck in wash mode? Once it hits exactly 48 minutes it stays there. Only several hours later it cycles through OR you have to turn it off put it in rinse mode to complete. Already tried all the basics (unplugging, no fault codes, cycled through the diagnostics everything good and working). Did the quick diagnostic cycle of 14 minutes and everything cycled through fine. Next step will be to put the bottom cont


... Fisher and Paykel Dishwashers

Kenmore Elite My top rack is not cleaning, but the bottom rack seems to be working fine. Has anyone else had this problem with a Kenmore elite?


I also have this problem, and my unit is only about 1 year old. The bottom gets clean but the top does not. I cannot see anything clogged or stuck open. \015\012\015\012I'd appreciate more possible answers.\015\012\015\012T ... Kenmore 15129 Built-in Dishwasher

MY SUPERBRA D/W JUST BLEW THE FUSEABLE LINK AFTER BEING REPLACED OVER SIX WEEKS AGO..REPLACED THE LINK AND D/W WORKED FINE..NOW HAS BLOWN AGAIN WITH NO VISIBALE ISSUES THAT WOULD CAUSE IT..ANYONE HAVE AN IDEA WHAT WOULD CAUSE THIS?


Plenty of ideas !!! 1st, if the voltage to the unit is too low or the size of the electric line is too long or too thin, then the electric will raise the current to try to compensate for the lack of voltage, and the fuse only knows or senses when th ... Dishwashers

My SB908WL Westinghouse dishwasher is tripping the switch when it goes to pump out the water. What are the likely problems and solutions please! If anyone has some expertise that would be great. (I have recently checked the soldering on the main panel and touched one point up, the rest are fine it seems). The element is working as there is hot water in the unit. We have small kids so maybe something is jammed in there? How do I get access to check. All input helpful. Thanks!


... Dishwashers

Newly installed Kohler Vinnata faucet and we can't get water from it. Water was working fine prior to replacing. Installed per installation instructions? Anyone have suggestions? Kohler not open u


Please go on line and question the Kohler tech:www.ereplacementparts.com/kohler-k690-vinnata-kitchen-sink-faucet-parts-c-1... ... Dishwashers

Karcher 2.56 keeps pulsing on and off whenever high pressure nozzle is attached. I have tried different nozzles and same thing is happening. when i press the lance without any attachment it works fine


Make sure you have bled all air from the system. Also make sure you have sufficient water supply; if house water pressure is too low or if your hose is too long or doesn't allow full flow, you may not be getting enough water to the unit. ... Karcher Pressure Washers

My dishwasher is a swan sdw7030w, water is going in and out the machine but no water is getting through to man part wher dishes are, am putting it on and it's jumping from my choosen cycle to economy while beeping, the salt light and starish looking 1 are both on as well, can anyone help me? It was working fine n old house, could it possibly be my water pressure as I can't think of anything else as a woman. Please help me.


... Dishwashers

I have a brand new Miele dishwasher which has worked grate since it was installed 2 weeks ago. It keeps shutting itself off & indicates an F13 fault. I looked in the manual, see that water is going in fine & pressure is good. It then says to clean water intake filter. How do I get to that ? I don't have a user maintenance manual. I'm on city water & doubt that the filter is clogged but My wife will kill me if I don't get it fixed today. Can anyone help. Glenn


On my Miele 1220 dishwasher, the inlet filter is inside the inlet hose connector, where it screws onto the water supply. To clean it:\015\012\015\0121. Turn off the stopcock.\015\0122. Unscrew the inlet hose.\015\0123. Remove the black rubber s ... Dishwashers

Cannot draw soap or cleaning solution from a bucket. Is their a adjustment screw to make it draw. Pressure washer works fine with just water. Lost the operators manual.


You first must slide the nozzle forward to the low pressure setting for it to inject any detergent. It will only draw the detergent in low pressure mode. If it still will not draw up the detergent, then the injector may be clogged. It must be through ... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

I have a GE Quiet Power 3 that has completly died. I cannot get a light to come on or anything to beep when pressing buttons. I checked the circuit breaker and outlet and they are both working fine. I tried pressing and holding the reset button on the front control panel and nothing. It seems to have just died at 2 years old. Anyone have a solution? GE wants $80 just to look at it.


A dead set simply means a cut off of power supply. Open the back cover of your dishwasher . Locate the area where the AC cord is located and look for the plastic fuse holder which is usually installed in one of the AC cord line open it and replace t ... Dishwashers

Ringsing Can anyone advise me as to how to adjust the AM-15 to rinse properly. It is great that it uses less water but I can not get a good rinsing action. Especially on outside of wares, inside appears to be okay and detergent and rinse amounts are fine. Any help would be greatly appreciated


What do you mean? A longer rinse cycle?I'm a hobart tech. ... Hobart 29 in. AM15-1 Free-Standing Dishwasher

GHD hair straightener Hi my GHD hair straightener suddenly stopped working. The fuse and plug seems fine but there is a continuous beep when I put it on and it goes off on its own in sometime. The plates are not even heating up Can anyone help pls? I bought it only a month ago by ordering online from GHD official website Is there someone in Bombay who can repair it?


... Dishwashers

Our dishwasher was taking in water, circulating it but not heating it up or moving through the cycle. My husband took the control panel off and there were some scorch marks on it so we got a new one. He replaced the control panel and the dishwasher went fine for one night. It heated up and washed everything perfectly. The next day when we put it on it was back to square one plus the lights on the control panel are now not working. Just wondered if anyone has any idea what we could do or are


Yes it's time to visit the dump ... Siemens 24 in. SE64A630GB Built-In Dishwasher

Have a whirlpool ADP 951 and no manual for it. Is was working fine and now the red light in the left hand corner is on and machine wont fill. When I start it by holding the button on the right hand side in, it will drain for about 30 seconds and then stop and green start light flashes. Can anyone offer a solution?


Some mod have codes / could be suds lock or slow drain . i would ( if front loader ) clean out pump . hope this helps . **** ... Dishwashers

My fridge wont work but freezer working fine


... Zanussi & Electrolux Fridge Freezer Handle Genuine

The ge profile dishwasher model PDW8280J10SS was purchased about 2 yrs ago. It was working fine up until Jan. 2009. It ran fine but the water stopped draining. I read were you should run the garbage disposal prior to running the dishwasher. I drained the water and did this. It worked fine for a while then the problem was back. Once again, Drained all the water, sucked it out with a turkey baister, moved the dishwasher and checked hoses etc. Once again, it worked fine for about 10-14 runs. It now


It is probably clogged at the pump or before. See if you can get outlet hose off the bottom before the pump. ... GE 24 in. Profile PDW8280JSS Built-in Dishwasher

Hi, my name is GAD. i work at a conference center. our model is quite an old version of the MH65-70 - maybe 1985? How do you adjust the water temp for both the rinse and wash cycles? the gage reads too hot. we have someone here who can service it, knows how to work the electrical, but does not know where to adjust the water temp. Is it a dial? a bolt adjustment? how do we lower the water temp sensor?


Hello Gad\015\012Send me the serial No. of your unit and let me see whether we are talking the same machine. \015\012The one I'm talking about have 3 thermostate with dial to adjust the temperature 1 for Hi temp safty no dial fixed tempe ... Moyer Diebel 28 in. MH65-70 Free-standing Dishwasher

Hi, I have a one year old karcher k.2.360, which has worked fine up unitl now. However, when I tried to use for the first time in several months, the detergent feed doesn't work. The detrgent tank is full, and the detergent hose isn't blocked at the intake end - you can easily blow through the filter/trap. The pressure side works fine. Cheers, Nic


... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1187 seconds