Having problems with your Pressure Washers ?

How do I get more water pressure out of my craftsman pressure washer 2250psi 5.5HP 2.2

\015 Model numbe 580767201\015

Answers :

Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I get more water pressure out of my craftsman pressure washer 2250psi 5.5HP 2.2


... Pressure Washers

Hello, I have a Craftsman Clean N Carry® 2150 psi Gas Pressure Washer w/4.0 hp Briggs and Stratton Engine. My problem is that I can't get any water to come out of the nozzel. What can I check to fix the problem? Also, where can I get a book to look at for parts and problems?


... Pressure Washers

Briggs and Stratton Troy Bilt gas pressure washer one year old. I can get water thru pressure washer and bleed the air, water comes out the hose just fine until I start the pump. Then, I lose all water flow. Pump runs fine but when it's running, no water goes through.


... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Cant get craftsman pressure washer to start - Craftsman 2700 Max Psi Pressure Washer 23 Max Gpm


... Craftsman 2700 Max Psi Pressure Washer 23 Max Gpm

Using a Bosch 1600W Pressure washer Aquatak 110 plus Was adjusting the twist pressure sleeve to get HIGH pressure and water supply stopped and sleeve seems fixed/seized. I turned power ON and OFF and turned water tap ON and OFF but still no water coming out of the nozzle. What do I do now?


... Pressure Washers

I have an older Landa Pressure Washer. The burner is not working. Once I get the machine running and water flowing to the pressure washer, with the wand pressed, I flip the burner on switch....and nothing...I have no idea how to work on a pressure washer burner. I have been told it could be the igniter, but I don't know how to fix it if it is. Any help is appreciated.


Check for 12V at the igniter connector with the unit running. If you have 12V and no igniter it may be stuck or bad. Thrun the unit off and read continuity across the DISCONNECTED igniter plug / terminals to the igniter. No resistance = open ignit ... Pressure Washers

2-yr old troy-bilt pressure washer with honda gcv160 engine. seems to run well, but when trigger is pulled get full pressure for less than 5 seconds before reducing to house water pressure. when left running, looks a black plastic pressure relief valve starts blasting hot water. appreciate whatever insight you can give. Thx


It sounds like an air lock. Try this: With the machine off, connect the hose to the washer and let it run for several minutes to get all of the air out of the hose, and to purge any air out of the pump. Shut off the water, and connect the high pre ... Briggs & Stratton Pressure Washers

I have a McCulloch FH160B power washer and it no longer builds up pressure. I haven't used this very much at all. I tore it apart and cleaned everything I could find. When i pull the trigger for the spray nozzle, I get line water pressure. When I release the trigger, the power washer sounds like it starts to build up pressure. When this was working correctly, the pump would shut off when the trigger was released. Any suggestions?


... McCulloch Pressure Washers

I HAVE A NEW CRAFTSMAN PRESSURE WASHER WITH KEY START. I HAVE USED IT ONCE AND WHEN I TRIED TO START IT IT WAS HARD TO START HAD TO PULL START IT. NOW IT WONT START. LET PRESSURE OUT HAVE HOSE OH AND RUNNING, NEW SPARK PLUG HAS OIL, GAS FILTER FINE.HAS GOOD COMPRESSION, BUT WILL NOT FIRE GET SOME RECOIL. GETTING GAS TO SPARK PLUG AND GETTING SPARK. IM LOST PLEASE HELP.


... Pressure Washers

Excell vr2500 pressure washer ,no pressure, took off high pressure hose at bottom of washer , get water flow, but flow does not change when engine is running full throttle


Check the water filter ---high pressurehose must have bbackpressure to develop pressure so disconecting it wont acheive ,much ,if you have agood water supply ,oil in the pump--- adjust pressure by srewing the brass fitting that the pressure hose atta ... Pressure Washers

I can't get the pressure washer to start up. The water is coming out of the hose, but there is no water pressure


If the washer is the kind that shuts off completely when the pistol grip is released, the problem is likely the little pressure sensor located near the output fitting (the threaded part to which the hose connects). The sensor is a little plunger held ... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

Pressure washer leaking water - Craftsman Pressure Washers


... Craftsman Pressure Washers

Two problems please: craftsman 2150psi briggs and stratton engine washer, will not start when hot. and secondly, i was washing with regular pressure, then noticed a pressure drop at the nozzle, then the unit shut down. no water leaks at the manifold. water supply was strong. any ideas?


Nozzle dirty, clean out with small diameter wire. ... Pressure Washers

When I turn on the shop force 1750 electric power washer I get water pressure in intermittent time frames. For example, it may run for a second then stop for ten seconds, then start again for three seconds then stop for 3 seconds then start for a half a second then stop for five seconds etc. until ?. This type of pattern continues for at least ten minutes, which is when I give up. I have tried adjusting the the water hose pressure, high, low. middle, nothing changes. This happen when I have the


The usual cause of this is sticky Orings in the water admitance valve.\015\012\015\012Take the valve apart and clean the bore with crocus cloth wrapped around a rod and replace the Orings and lube with a bit of plumber's grease and reasse ... NIB Shop Force Universal Pressure Washer Accessoriesnib

Hi. I have a Briggs & Stratton 2800PSI gas pressure washer. I can get it to start, but after about 5 min, then it quits. I have cleaned the carb, change oil, changed plug, new gas, cleaned/checked air filter. Nothing will keep it running. Wondering if it may be not enough water pressure, but would that cause it to stop like that? When it runs, it does a good job, but it stops just as you get going. Do you have any other suggestions? Thanks!


If it wont start, check for spark.how you do that,ok take the spark plug wire out put it close to the sparkplug(use some gloves or something to insulate your self from get electric shot from the spark) find some one who pull the start rope, if you do ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

The oil in my gc160 Honda pressure washer is getting water in it some how. Could it be something with the water pump gasket or what? And I can get it started but can't keep it running un less I keep spraying starter fluid in the carbar. Please help ?


... Karcher 2500 PSI Pressure Washer

Pressure Once I have the powerwasher started and going (water to it before starting) i can't get it to go to full pressure it will prime up like it's going to go to full pressure give me just a shot of full pressure then go back down to probably half pressure and remain there then prime again for a second then back a coninues cycle! Maybe there's a seal or something somewhere I should look at. Hose and pressure from house is good, the seal whee the hose attaches to the bottom of the washer is ne


This is usually a problem with the "dump valve" defective in not being able to hold the pressure but only able to release it prematurely as it should only do so when to much pressur is built up inline. Only recommend qualified pump tech. But check pu ... Coleman Pressure Washers

Craftsman pressure washer with honda engine. low pressure and volume on high pressure setting. lots of water volume on low pressure setting. Screens not clogged.


Sounds like pump is not making pressure. Thats why you get flow, but no pressure.\015\012If it sat for awhile, check shaft connection to pump. Sometimes the impeller or shaft will shear partially due to corrosion when stored. Seals on pump valv ... Pressure Washers

Not getting pressure I was washing my car with warm water from my house. I shut off the pressure washer to soap up my car when I restarted it I got very little pressure.


... Dewalt 3800 PSI Pressure Washer

Have whirlpool dishwasher model DU1055XTSS2 and the top rack water wheel does not spin. Operated the washer with door opened and it gets water but doesn't spin. There are no restrictions to the jets on wheel and the wheel turns feeely. The only thing i can figure is inadequate water pressure....


... Dishwashers

I have a craftsman 4.5hp quantum xte pressure washer 1800psi/4.5hp/2.0gpm mod 580.761800. I have to start the washer before I turn the water on and just today started with if I let go of the trigger on the wand the washer stalls. Can you advise as to what the problem is and how to solve? Thanks ****


The pressure relief valve(bypass) is most likely stuck or clogged. take the relief valve off and check for broken or jammed parts..there should be a bypass hose that goes around the pressure valve ... Briggs & Stratton Pressure Washers

I have a model PW 2200 gas pressure washer. It suddenly lost it's high pressure the other day after working fine for @10 minutes. It's getting plenty of water, but the engine doesn't seem to rev up to give it the high pressure. The operating instructions say to check the oil in the engine, and the PUMP before starting, but I haven't found any place to check for an oil level in the pump????Any ideas, I'm very confused.


... Pressure Washers

Engine starts up on honda 2500 pressure washer water comes out wand but will not get up to pressure


Have you checked the hydraulic fluid level in pump? ... Honda Maxus Pressure Washer MX5222

Kenmore washer 17039 not getting water pressure to wands


... Kenmore 24 in. 17039 Built-in Dishwasher

I have a karcher 2400 psi pressure washer and it doesnt get water pressurized when pulling wand trigger.


The most comon problem with thease is a stuck bypass valve, this is the valve that alowes the water to bypass round the pump when the triger is closed, when they stick all of your pressure runs around the pump and not out of your nozzle,,\015\0 ... Honda Karcher G2400HH-R Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1224 seconds