Having problems with your Pressure Washers ?

Pressure washer is getting water in oil

\015 Water is mixing with oil\015

Answers :

Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a model PW 2200 gas pressure washer. It suddenly lost it's high pressure the other day after working fine for @10 minutes. It's getting plenty of water, but the engine doesn't seem to rev up to give it the high pressure. The operating instructions say to check the oil in the engine, and the PUMP before starting, but I haven't found any place to check for an oil level in the pump????Any ideas, I'm very confused.


... Pressure Washers

Hi. I have a Briggs & Stratton 2800PSI gas pressure washer. I can get it to start, but after about 5 min, then it quits. I have cleaned the carb, change oil, changed plug, new gas, cleaned/checked air filter. Nothing will keep it running. Wondering if it may be not enough water pressure, but would that cause it to stop like that? When it runs, it does a good job, but it stops just as you get going. Do you have any other suggestions? Thanks!


If it wont start, check for spark.how you do that,ok take the spark plug wire out put it close to the sparkplug(use some gloves or something to insulate your self from get electric shot from the spark) find some one who pull the start rope, if you do ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

The oil in my gc160 Honda pressure washer is getting water in it some how. Could it be something with the water pump gasket or what? And I can get it started but can't keep it running un less I keep spraying starter fluid in the carbar. Please help ?


... Karcher 2500 PSI Pressure Washer

My 1750 huffy power washer was hard to get water pressure for about 10 minutes, once the machine was putting out pressure i noticed it was leaking oil from the bottom of machine need help with the problem


There is sticking valves in the pump ... Pressure Washers

Pressure washer is getting water in oil


... Pressure Washers

Karcher K3.91, lost some pressure and pulsing when trigger is release. stripped it down and checked all six valves and there all sealing as they should. i took apart the unloader valve cleaned and inspected and thats fine. there is NO water leeks anywhere or oil. preasure washer is 2 years old and gets used once a week for ten minutes. i really dont understand why its playing up


... Pressure Washers

Water is getting into oil - Honda Pressure Washer PSI 3000


Packing or ceramic pistons broken ... Honda Pressure Washer PSI 3000

Water gets into the oil - Honda Pressure Washer PSI 3000


Could be a faulty oil seal between pump and engine? ... Honda Pressure Washer PSI 3000

Briggs and Stratton Troy Bilt gas pressure washer one year old. I can get water thru pressure washer and bleed the air, water comes out the hose just fine until I start the pump. Then, I lose all water flow. Pump runs fine but when it's running, no water goes through.


... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Using a Bosch 1600W Pressure washer Aquatak 110 plus Was adjusting the twist pressure sleeve to get HIGH pressure and water supply stopped and sleeve seems fixed/seized. I turned power ON and OFF and turned water tap ON and OFF but still no water coming out of the nozzle. What do I do now?


... Pressure Washers

I have an older Landa Pressure Washer. The burner is not working. Once I get the machine running and water flowing to the pressure washer, with the wand pressed, I flip the burner on switch....and nothing...I have no idea how to work on a pressure washer burner. I have been told it could be the igniter, but I don't know how to fix it if it is. Any help is appreciated.


Check for 12V at the igniter connector with the unit running. If you have 12V and no igniter it may be stuck or bad. Thrun the unit off and read continuity across the DISCONNECTED igniter plug / terminals to the igniter. No resistance = open ignit ... Pressure Washers

2-yr old troy-bilt pressure washer with honda gcv160 engine. seems to run well, but when trigger is pulled get full pressure for less than 5 seconds before reducing to house water pressure. when left running, looks a black plastic pressure relief valve starts blasting hot water. appreciate whatever insight you can give. Thx


It sounds like an air lock. Try this: With the machine off, connect the hose to the washer and let it run for several minutes to get all of the air out of the hose, and to purge any air out of the pump. Shut off the water, and connect the high pre ... Briggs & Stratton Pressure Washers

My Troy Bilt power washer (using Honda GCV160 engine) has no pressure coming from the pump. I checked the water flow, everything seems fine. I believe the pump needs oil added, however, I can't seem to firgure it out (how to add oil to the pump). I did notice that previously, I used to see drops of oil coming from under the pump. I I have a bad seal, can I add oil and test the pressure before I change the seal? Please advise.


I had a similar problem. Turns out I had left the hose disconnected and some sort of wasp built a paper type nest inside the washer tube that the hose connects to. I had to take the pump off and take apart and then cleaned it out with a screw driver. ... Honda Black Max 2600 PSI Pressure Washer

No pressure McCullough pressure washer has no pressure after siting all winter. I took apart the assembly and the oil leaked out, also I noticed yhe o-ring that seals the two pieces together seems to have been blown out. Where can I get parts and oil. Thanks for any advice.


... McCulloch FH140A Electric Pressure Washer

I HAVE A NEW CRAFTSMAN PRESSURE WASHER WITH KEY START. I HAVE USED IT ONCE AND WHEN I TRIED TO START IT IT WAS HARD TO START HAD TO PULL START IT. NOW IT WONT START. LET PRESSURE OUT HAVE HOSE OH AND RUNNING, NEW SPARK PLUG HAS OIL, GAS FILTER FINE.HAS GOOD COMPRESSION, BUT WILL NOT FIRE GET SOME RECOIL. GETTING GAS TO SPARK PLUG AND GETTING SPARK. IM LOST PLEASE HELP.


... Pressure Washers

I have a McCulloch FH160B power washer and it no longer builds up pressure. I haven't used this very much at all. I tore it apart and cleaned everything I could find. When i pull the trigger for the spray nozzle, I get line water pressure. When I release the trigger, the power washer sounds like it starts to build up pressure. When this was working correctly, the pump would shut off when the trigger was released. Any suggestions?


... McCulloch Pressure Washers

Excell vr2500 pressure washer ,no pressure, took off high pressure hose at bottom of washer , get water flow, but flow does not change when engine is running full throttle


Check the water filter ---high pressurehose must have bbackpressure to develop pressure so disconecting it wont acheive ,much ,if you have agood water supply ,oil in the pump--- adjust pressure by srewing the brass fitting that the pressure hose atta ... Pressure Washers

Changing oil on a high pressure washer with Comet Water Pump


... Comet BXD2527 Pressure Washer Pump

I have an excel pressure washer 11 hp Honda engine. water is leaking into the cat pump 4hp40gl causing the oil to become milky, after the washer sits overnight the oil clears up. Any and all help will be appreciated. Thanks


... Caterpillar Cat Pump Pressure Washer Pump 3SP30G11

Pressure washer has water in oil - Pressure Washers


... Pressure Washers

I cant get water to spray from my pressure. the oil cap is throwing oil out the little hole. no pressure is coming out of the nozle. AR. model#SJV 2.5G27-1


... Annovi Reverberi RMV2.5G27D Pressure Washer Pump

When I turn on the shop force 1750 electric power washer I get water pressure in intermittent time frames. For example, it may run for a second then stop for ten seconds, then start again for three seconds then stop for 3 seconds then start for a half a second then stop for five seconds etc. until ?. This type of pattern continues for at least ten minutes, which is when I give up. I have tried adjusting the the water hose pressure, high, low. middle, nothing changes. This happen when I have the


The usual cause of this is sticky Orings in the water admitance valve.\015\012\015\012Take the valve apart and clean the bore with crocus cloth wrapped around a rod and replace the Orings and lube with a bit of plumber's grease and reasse ... NIB Shop Force Universal Pressure Washer Accessoriesnib

I can't get the pressure washer to start up. The water is coming out of the hose, but there is no water pressure


If the washer is the kind that shuts off completely when the pistol grip is released, the problem is likely the little pressure sensor located near the output fitting (the threaded part to which the hose connects). The sensor is a little plunger held ... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

Pressure Once I have the powerwasher started and going (water to it before starting) i can't get it to go to full pressure it will prime up like it's going to go to full pressure give me just a shot of full pressure then go back down to probably half pressure and remain there then prime again for a second then back a coninues cycle! Maybe there's a seal or something somewhere I should look at. Hose and pressure from house is good, the seal whee the hose attaches to the bottom of the washer is ne


This is usually a problem with the "dump valve" defective in not being able to hold the pressure but only able to release it prematurely as it should only do so when to much pressur is built up inline. Only recommend qualified pump tech. But check pu ... Coleman Pressure Washers

What oil do i use for my wolf pressure washer water pupm


... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1540 seconds