Having problems with your Pressure Washers ?

My honda powerstroke 2600 psi won't start


Answers :

Sfhardyg
\015\012Make sure you are getting spark at the spark plug, to do this:
Remove your spark plug and check to be sure you are getting a bright blue spark at the spark plug.
You do this by grounding the plug on the head of the engine and cranking the engine or by pulling the crank rope...watching the plug for spark.
If you are getting a nice blue spark then skip A below and go to B.
\015\012A...If you do not get a nice blue spark then you may need to replace the electronic module.
Note: If you have to replace the module be sure to measure the position it is in, it is critical to starting.
Take a picture for later reassembly.
\015\012B...Also take some fine grit sandpaper (not emery) and lightly sand the flywheel where the magnet is located to clean any rust or corrosion from the magnet area.
Then follow the procedure below:
------------------------------------------------------------------------------------
Sounds like you have dirt/debris in your caburetor jets,fuel passages or a diaphgram that is becoming non-flexible.
Check/Clean/Replace your Air Filter, a dirty air filter can make your engine run to rich with fuel.
\015\012Note: ALWAYS USE COMPRESSED AIR TO CLEAN YOUR JETS AND PASSAGES, VERY IMPORTANT.
\015\012Note:Before you disassemble the carburetor:
Write down on a piece of paper and or take a picture of how the linkage attaches to your carburetor for later reference when you go to reinstall your carburetor.
Mark each piece with a awl, or some kind of sharp instrument that will make an alignment scratch before you disassemble the carburetor into separate pieces.
That way you will know which way it goes back together when you reassemble it.
\015\012Sometimes you can get by with priming the carburetor or by using a very small shot of starting fluid and letting it run a few times like that, and it will flush the gunk out of the jets,but most of the time you will need to rebuild the carburetor.
Be sure to check your fuel tank for water and dirt/debris, if there is water/debris then you need to clean your tank.
Check you fuel line/s condition...after a while they will degrade and need replacement.
\015\012Check/Clean/Replace your fuel filter if you have one.
When you remove your fuel lines from the carburetor be sure to make a drawing or take a picture of how the lines are connected to the carburetor.
Also a good time to take a picture for later reference for reassembly.
\015\012If the mower is over a couple of years old, then I recommend that you buy and install a new carburetor repair kit,because the diaphragm will get hard and that will cause it to be hard to crank.
The diaphgram may look good and flexible, but it can be deceiving and not act as a fuel pump as it should because it has become too hard and will cause hard starting,start and run and shut off, etc.
\015\012When you clean your carburetor, I recommend that you use a laquer thinner type cleaner to clean and dissolve the laquer build-up in the float and needle jet passages.
Be sure to remove all plastic and rubber parts before using the laquer thinner because it can dissolve the plastic parts and render them unuseable.
Be sure to use COMPRESSED AIR to blow out all the fuel and air passages.The higher air pressure is needed to blow some of the trash/debris from the fuel or air passages.
Be careful when blowing out the passages, because there are sometimes small rubber type seats in the bottom of some of the passages.
Keep in mind that the float (if you have one) for the carburetor must be level when you go to reassemble the carburetor or follow the instructions you get with the carburetor kit, or you could also ask the parts man that you get your kit from.
When you clean your carburetor and remove the jet screws, you will first need to lightly seat the jet screws.
But before you lightly seat the jet screws count the number of turns it takes to seat the jet screws from their original position.
Be sure to mark the turns down on a piece of paper.
That way when you put the jets back in, you know to lightly seat them first and then turn them back out to their original position before you started.
Once you have your carburetor cleaned/rebuilt that should solve your problem.
Please take time to rate me
Bud
Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Honda 11.5hp pressure washer wont start - Honda 2500 PSI Gas Pressure Washer


... Honda 2500 PSI Gas Pressure Washer

Karcher 2400 psi with honda motor started up big puff of white smoke from exaust it shut off noiw wont start whats going on


I have a john deere 3000psi pressure washer with similar problem. Running fine then a puff of smoke and it shut down. I checked the oil and found it full of water. Not only that but since I still had the water turned on, the water was flowing out of ... Karcher 2500 PSI Pressure Washer

KARCHER 3000 PSI WITH HONDA ENGINE WONT START


... Karcher G 3050 OH

Hondar 2500 pressure washer wont start - Honda 2500 PSI Gas Pressure Washer


... Honda 2500 PSI Gas Pressure Washer

I have a excell 2500 psi max honda 5.5 ho vr2522 2.2 gpm presser washer and has been stored for about a year, still looks brand new and has only been used twice before, it has oil and was stored with no gas in the tank, i put fresh gas in the tank and blead the fuel bowl until fuel ran out like it should, the washer wont start, ive checked the turn on switch as well and the fuel cut off knob, i spayed gas in the carb and it fired up but stopped running as fast as it began to run, its not getting


... Honda Black Max 2600 PSI Pressure Washer

My honda powerstroke 2600 psi won't start


Sfhardyg\015\012Make sure you are getting spark at the spark plug, to do this:Remove your spark plug and check to be sure you are getting a bright blue spark at the spark plug.You do this by grounding the plug on the head of the engine an ... Pressure Washers

Honda 2700 psi GC160 pressure washer will start with starter fluid in carburetor but wont stay running? Changed sparkplug cleaned carburetor, Added fuel cleaner then let set and drained all fuelandadded new. Seems as if their is no fuel going from the tank to the carburetor?


... Pressure Washers

2050 PSI Gas Pressure Washer - 20244: my excell pressure washer wont start. pull start t...


... Briggs & Stratton Gas Pressure Washer 20244

Wont start I have a North Star pressure washer that has been in storage for three years.It has the Honda motor GX 160 5.5 I put in new gas changed the oil, air filter,and spark plug.But it wont kick over. Im not sure how to work the levers upon starting it.Theres one for gas, choke,idle,and of course an on switch.Please help


Tip a cap full of fuel in top of the carb to start intitially, check for spark as common fault is on/off switch, If no spark, link the 2 wires on on/off switch together. ... Pressure Washers

I have a Husky 2600 PSI power washer with the Honda GCV160 engine that I can't get to start. It was okay when I purchased it from Home Depot last spring but now I've tried putting new gas in it, spraying carb cleaner, new spark plug, and it still won't start. I only ran it for about 30 minutes when I first purchased it. The guy at the service desk at Home Depot told me that the water hose should be attached and turned on while trying to start. Is this true or would this be starting the motor und


You can eliminate the motor by unbolting the pump from it and then if it will start the problem is with the pump or the unloading valve.If it does not start with the pump removed then you check for spark and get the carb cleaned or have a kit put in ... Karcher 2500 PSI Pressure Washer

Honda gcv160 wont dipenve detergent - Craftsman 2600 PSI Honda Powered Pressure Washer


... Craftsman 2600 PSI Honda Powered Pressure Washer

Why wont blackmax power washer 2700 psi honda engine wont stay running once i spray


... Honda Pressure Washers

Honda gcv160 wont dispence detergent - Craftsman 2600 PSI Honda Powered Pressure Washer


It will not draw soap while using pressure take out the nozzle or use the large black nozzle ... Craftsman 2600 PSI Honda Powered Pressure Washer

I have a Honda GC160 5 horsepower power washer with 2400 psi. When its cold it is easy to start but after it has been running for a while the only way to start it is to have the water shooting out of the wand. Once it is hot and running if i stop the stream of water (release the trigger on the wand) then the machine shuts off. It seems like the only way to keep it running is to constantly have water running through the wand. Please help


... Pressure Washers

My Troy Built 2500 psi power washer with Honda engine GCV has been stored for 2 years. I changed the gas and could not get it to start. Which is the start position for the valve on the gas line - Horizontal or Vertical? Thanks, Bill Gray Melbourne Beach FL


... Pressure Washers

Honda 4.5 hp engine wont start, need a little help was hard to start from new


... Pressure Washers

I have a 4,000 psi, 4.5 gpm 45G cat pump powered by a 13 hp honda engine I can not seem to be able to adjust the unloader valve to give me pressure over 950 psi and even at lower pressures, the pump will not deliver consistant pressure without bouncing off to the relief stage and back into the tank Are unloader valves worth repairing, or should i look at just buying a new one my current thought is to buy an EZ start Pulsar


I would just purchase a new unloader valve, they usually aren't worth rebuilding. I would like to have a picture of the set up that you have, if you can send me a picture of the unloader region of the pump I can get you are price on a new one. email ... Honda Pressure Washer PSI 3000

My Honda 2600 psi power washer will not pull to start. It was running great then I allowed the neighbor to borrow it. He ran the washer till it was out of gas and proceeded to refuel and at this point it would no longer start. The pull cord is out about 4-6 inches out and I am concerned about taking the casing off myself. Fearing that it may throw more off on the unit. If i take the casing off are there any spring loaded parts that will dismount? What should I do? Spark Plug? Turn


You should be fine to take the recoil off, there shouldn't be anything that shoots out at you. You might want to check the oil level on the engine, many of the Honda engines won't start unless there is enough oil in them. If your oil level is fine, c ... Honda Pressure Washer PSI 3000

I have a NorthStar pressure washer (2000 psi / 2 Gal /Min.) with a Honda motor. We tried to start it a couple weeks ago and could only get it to run on starting fluid. Sprayed the carb with carb cleaner, still no dice. Am I actually going to have to use my mechanical talent to make this thing run (I hate when that happens)?


What is the model number of the Honda engine? ... Northstar Pressure Washer 2800 PSI

I have a excell 2600 psi with Honda GC 160 motor I am having problems trying to start it. It will turn real easy for a couple of times, then it get's real hard to pull for awhile then loosens up again and only starts with starter fluid.


Change the Spark Plug. Drain the old fuel out and replace with fresh gas. Prime, choke and start. ... Honda Pressure Washers

I have a 2550 psi pressure washer with a 6.75 hp briggs and stratton engine with ready start. i wont start. has gas and oil plug looks good. any solutions?


... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

13 hp honda pressure washer 3000 psi 4gal/min Hard to start and dies out after 20 seconds after the engine gets hot and running after multiple starts the engine will stay running but then dies every 30 minutes


There are a couple of things that can cause this problem. The first thing to check is if you are loosing spark. Dying after it gets hot sounds like to stater is failing in the engine. If you loose spark this is more than likely the issue. If you are ... Honda Landa PG 3500 PSI Pressure Washer

Troy-bilt pressure washer 2350 psi wont start after use


... Pressure Washers

Honda powered gx160 model pressure washer wont start


Did you drain out the fuel before you stock it? If you didn't, you may need to clean the carburetor or replace a new one because the fuel inside has become a kind of stick varnish. You may take a look at following link to see how to change or replace ... Honda 8 HP Engine

Craftsman 4 hp 2150 psi pressure washer wont start


Go to www.karcher.com ,click on your region and then click international. Enter the model of the machine or the type number . That is is the first 8 digits of the number under the b ... Karcher 2500 PSI Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0733 seconds