Having problems with your Pressure Washers ?

Where can i get an ignition coil for a spw-2 scorpion presure washer


Answers :

Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Where can i get an ignition coil for a spw-2 scorpion presure washer


... Pressure Washers

I have an older Landa Pressure Washer. The burner is not working. Once I get the machine running and water flowing to the pressure washer, with the wand pressed, I flip the burner on switch....and nothing...I have no idea how to work on a pressure washer burner. I have been told it could be the igniter, but I don't know how to fix it if it is. Any help is appreciated.


Check for 12V at the igniter connector with the unit running. If you have 12V and no igniter it may be stuck or bad. Thrun the unit off and read continuity across the DISCONNECTED igniter plug / terminals to the igniter. No resistance = open ignit ... Pressure Washers

Manual for scorpion spw-2 pressure washer


... Pressure Washers

I need an ignition coil for a Blue Max 2200/03435, where do I get the part?


... Psi Blue Max 2200 High Pressure Gas Power Washer

My pressure washer runs for a good ten minutes, then it shuts itself down. I thought it might of been the ignition coil, which i just replaced and the problem is still the same. Any ideas why this is happening? Thanks!


Two reasons why. Oil level is very low and needs changing, when oil level is low, a sensor protects the engine from running dry. Or you are using your blaster in an area that is hot and the thermal protection is shuting the engine off. Also check for ... Pressure Washers

I can't get the igniter to start on north start pressure washer #157224. Fuses ok, indicator light in heat switch does not illuminate. Blower works, fuel dripping out. Cleaned fuel tank and pump and filter too! Tried jumpering past the thermostat didn't help either. Also, swapped pump and heat switches on main panel. No help!


... Pressure Washers

I have a troy built power washer powered by honda. It runs for 10 - 15 minutes and then dies. I have replacced the ignition coil, spark plug, rebuilt the carburetor, checked fuel flow and placed the unloader valve and it still dies. Once it dies and the pressure is released it repeats the problem. Any suggestions?


... Honda Pressure Washer PSI 3000

The pull start broke off when I was starting the pressure washer. I bought a new coil w/handle but I can't figure how or where to attach it. We took off the face guard and I'm staring at this big circular silver thing which I'm assuming starts the engine. How do I get that off and what do I attach the sting to. Thanks!


... Honda Maxus Pressure Washer MX5222

I have a Bosch SHU53513UC/U12 dishwasher. My initial problem is that the washer smells bad after a cycle and I've noticed some water sitting in the bottom of the unit. After running a diagnostic test, it results in a "2" heating fault. I followed your advice and used a current coil to and attached it to the GYBK-a1-3 hot wire on the control board. After running the test again, it only gets as high as 1.15A and manual says it should reach 11A. What should I do next?


Hello,Welcome to FixYa. ... Dishwashers

Looking for a manual for my scorpion spw 6.5 high pressure washer


... Pressure Washers

I have a Honda xr2600 power washer. When I tried using it, water was squirting from the top of the gun. I took it apart to find that there are o-rings on top of some kind of washer---looks like a lock washer but it's made of cardboard??? Two of these washers were broken. I can get the o-rings but I can't seem to find the washers. I tried getting the manual for this model on line with no luck. Any assistance will be greatly appreciated.


The washers that you describe are made of teflon and are split to facilitate installation and/or allow expansion as they wear. These washers are actually seals and at times are used together with orings to seal high pressure. You should ... Honda Pressure Washers

Hi I have a Nemo Dishwasher and the top spray arm is not turning. The bottom one is going fine and there is certainly plenty of water getting into the washer as I opened the door with the washer going and it flood me. I can see the water getting into both spray arms - the bottom one has a excellent upward spray and turns - the upper spray arm has water getting into it but it will not turn. I have cleaned the dishwasher out and any internal parts that I could find so it is spotless - this is so f


... Fisher and Paykel DS602 Dishwasher

Home Depot has a lawn mower with the Honda GCV160 Electric start version engine. They also have a pressure washer with the Honda GCV160 engine. I have a disability that makes it difficult to pull the starter rope. I would like to get the electric start on the pressure washer. My local Honda bike shop service center said they use different blocks. Can I get a pressure washer pump mounted to the Honda GCV160 Electric start version engine? If necessary, are there adapter plates that can be purchase


... Karcher 2500 PSI Pressure Washer

A small cap fell down into the drain area on my Kitchenaid dishwasher. I removed the lower washer arm trying to get to the drain area. I could not figure out how to get to it, but now I have another problem. I can't get the washer arm back on!


Grab the center nut with pliers and pull up on it while spinning the spray arm. ... Dishwashers

Excell r 2522 presure washer pump rebuild


I like http://www.ppe-pressure-washer-parts.com/excell-vr2522-replacement-parts-pump See pump upgrade and compare to rebuildin ... Honda Pressure Washers

Drain Clogged I have a Kenmore Quiet Guard Plus dish washer. The water will not drain from the unti. I believe the drian in the dish washer is pluged. I removed the 8 screws from the pump/strainer unit at the bottom of the unit I removed the top that the screws were holding donw, but can't figre out how to get to the drain to unplug it. The center metal unit is exposed and nut head is exposed. What do I do next to get to the drain hose to unplug it?


You might try pouring liquid plummer in the drain part and jet it set it shouold eat through whatever is in there ... Dishwashers

Homelite presure washers wy my presure washer only start if i put a litle bit of gas true the carburator but dont stay on


Sounds to me like some of the jets in the cab are plugged remove the carb and clean the jets and passages ... Pressure Washers

Whirlpool DU940 dishwasher. Opened the door and felt that the coil was warm but washer has not been turned on and control panel does not function. Removed power from washer and coil stopped heating but control panel still not working.


... Whirlpool GU2400XTP Built-in Dishwasher

Fuel pump not working when trigger pulled, all temp. lights on. checked flow switches all ok and new fuel pump coil an stalk fitted. the burner will work if the o ring removed from bottom of stalk allowing fuel through so something is stopping coil from getting 24v(it does get a nominal voltage of 10v)... anyone got any thoughts


... Pressure Washers

My electrolux dish washer model eidw6105gso stopped before it completed the cycle. All the selection lights were flashing and i could not get any functions to change. I killed the power at the breaker to try to reset and that didn't work either. I removed the panel on the front on the bottom to see if there was a reset button and found another display that is showing a light on the turbidity location. what is this and what might i do to get my washer back working?


... Electrolux Dishwashers

Bad i bought the 1800 psi washer 2 years ago the head on the hose blew off you sent me a new hose it did the same thing. you sent me anouther hose and it blew off too. finaliy you sent me a hole new washer because of a recall. i didnt get to use the first one all year and now i was going to use the new one the other day 3-28-09 and it is the same washer i had and the head blew off so now i have two washers with no hose, that i can not use. so what do i do now ?


... McCulloch FHH18A Electric Pressure Washer

We have run our dish washer several times, however, the dishes are not getting cleaned. We first ran it on "normal wash." The second and third time we ran it on "pots and pans." Not only are the dishes not getting cleaned, but the soap is hardly getting dissolved. We use liquid dish soap too. I noticed this last time, at the end of the wash, the soap was getting built up on the front-right (when facing the machine) and had turned into a solid clump; almost like plaster. I don't have a manual so


First idea goto your local home depot they make a product called AFFRESH for front load washing machines and dishwashers run this tablet inside your dishwasher with no dishes on the inside on the hotest setting this usually takes out all build up wit ... Dishwashers

I do need the igniter for the burnner / my igniter i think it is the wrong one , it is too shot and the spray of oil do not fire/ i think the 'plugs' is little short to ignite on the spray , comes on and off / but i have sparks all times, only dos not get fire , do i need longer plugs !!!do go under the noze of spray!!


Send me a email at [email protected] I am an dealer for Northstar and many other brands of pressure washers. I need the model number off the machine if you have it. I can get you th ... Northstar Gas - Powered Wet Steam & Hot Water Pressure Washer 2700 Psi, 2.5 Gpm

The top rack dishes do not get cleaned. I have run the vinegar rinse. The bottom rack dishes get cleaned. It doesn't even look like the top rack dishes get wet. I ran the washer without the top rack in and I think water was coming down from the top. What can I do?


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Dishwashers

Hi i have a whirlpool dish washer - model : ADP4731/5 , AAA class . I keep getting a F7 error message and it is not allowing me to turn the washer on , if i hold the start button down it allows the washer to go for 30 seconds before the error comes back up and it stops working again


... Whirlpool Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0797 seconds