Having problems with your Pressure Washers ?

Simoniz s1500 My Simoniz S1500 don't stop when I release the gun. Somebody have a solution ?


Answers :

Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Simoniz s1500 My Simoniz S1500 don't stop when I release the gun. Somebody have a solution ?


... Pressure Washers

I have a Briggs & Stratton gas power washer. This is the 1st time this year that I have used it. I put in fresh gas, hooked up the water supply. The engine started and then quickly stopped. I had to release the water pressure in the hose before I could pull start the engine. The only way to keep the engine running is to hold down the spray nozzle trigger. Once that is released the pressure in the hose builds up and the engine stops.


Sounds like the unloader is not working correctly. Try replacing it and see what happens. ... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Gun wil not trigger after stopping


I'm not real clear on what you're saying, but I think it's that the trigger will not shut down the pressure as it should. It stays stuck on. The other info is how long you've had the washer, but my hunch is that maybe you have hard water, and the dep ... Karcher PSI Electric Pressure Washer

Nilfisk Alto Active Waterblaster.Starts up good. When I release trigger on gun it does not start pressure again. I have to take water hose off


... Pressure Washers

My Karcher 411A seems to have lost pressure. Behaviour is this, when you press the water release on the spray gun you get 100% pressure for like 10 seconds and then it seems to dwindle down to 30-40% of its total pressure. When the pressure cuts down I can hear more noise coming from the gun sprayer aswell. So not sure if the problem is in the gun or the main pump unit ?


Sounds more like a clog on the intake side. Check the filter and the hose on that side. ... Pressure Washers

Gun leaks dont know if i lost a chek valve when dissasembledcan you buy a kit for troy built gun model 020208 what parts are installed insise of gun


You probably can get a kit, but before you do check out northerntool.com. it might be easier and cheaper to just replace the handle ... Honda Pressure Washer PSI 3000

I have a prima lpr 450 and it has stopped working. Now, when I turn the power button on the lights flash and then it beeps around 30 times. When I close the door it makes a noice as if it is starting then it stops and the beeps also stop. I have seen on the web that many others are seeing tyhe same issue but I have not seen a solution. Hope you can help.


... LG LDF9810ST Built-in Dishwasher

Trigger gun I just install a new hose for my Karcher 330?Hose is working, but the trigger gun is lose, no turn off went is released, the equipment is always on ?..did I missing a part inside the gun ?..


It sounds like you left out the spring in the hose.There are about 10 different models of K330 with several types of guns. Go here and search until you find ... Karcher K2.26 Electric Power Washer

How to re-assemble Simoniz S1900 Spray gun - Can you show me how to put the spray gun back together? I have 2 springs-don't know where they go??


... Pressure Washers

I can't get any water pressure out of the gun itself, it was working fine, then it just stopped. Any suggestions? Is there a way to take the gun apart and clean out any deposits that might have built up in the shaft?


Yes you can take the gun apart it usually unscrews from the middle. ... Campbell Hausfeld Pressure Washer Gun - Electric/Gas Up To 2200 Psi - PW102400AJ

Replacement gun and hose for simoniz cl 11 - Omega Simoniz 1300 Psi Pressure Washer


... Omega Simoniz 1300 Psi Pressure Washer

I just purchased a Simpson Megashot V3000 Pressure Washer and noticed the engine would stop running every time I released the wand trigger. Also, water was constantly spraying out of a valve underneath the unit - I assume it's some type of pressure release valve but there is no mention of it in the owners manual. I am thinking about returning it to Costco for a refund.


... Simpson Pressure Washers

My Bosch dishwasaher model SGS53 has stopped working and has water in the bottom of it , i have cleared this and checked the small impeller for blockages - this is ok. i have also checked the water inlet filters and the drain tube is clear . I have the top and left sid panel of and when i lift the red rod it allows watrer to come in but stops if i release the rod thr lever in the base of the machine int which the red rod fits appears th be at its lowse level and therefore the red rod cannot be p


... Dishwashers

My power washer gun sticks on high pressure and I have to turn the machine off to make it stop. Can I replace the seals in the gun assembly?


Some you can take apart a match up the seals at a hardware store ... Pressure Washers

Mdb7759 Control panel stopped working, replaced it and got two cycles out of it and it stopped working again. I feel that this machine is a real lemon and should be recalled. Any possible solutions? I've tried the heated dry/ high temp wash reset but I does not work. Help


... Maytag 24 in. MDBH950AWS Built-in Dishwasher

Kenmore dishwasher stops after washing/sensing cycle. releases the cleaning pack and then does stops


... Kenmore Dishwashers

My dishwasher BOSCH SGS4802EU/12 dont stop after 92 minutes, wich is the time of one cycle. it take more than 3 hours to finish. I think that can be resolved if y make a reset on the dishwashwer, but y dont how to make the reset. Can you help me please? Best regards. Pedro Antunes


... Bosch Dishwashers

Asko Dishwasher DW20.1 d3120 Water not coming through inlet valve. I have replaced the inlet valve - solenoid only releases when on/off switch and start button are pressed and released simultaneously. A burst of water comes out at that point and stops. What could be wrong?


Hi, Welcome to FixYa.\015\012\015\012I'll start by saying your description sounds exactly like a symptom of a faulty control board on Asko dishwasher's...specifically the relay responsible for energizing the fill valve. It sounds to me like the relay ... Dishwashers

Karcher G2650 OH - When I start engine pressure builds up and the engine will stop- When I pull the wand handle back - I get a high release of pressure - I can hold the wand open and start the engine and it will run until I close the wand - egnine stops


Take a look at this link, I think this might solve your problem\015\012\015\012http://www.wmpcs.com/blog/?p=72 ... Pressure Washers

It has stopped draing, the line is clear and the draining pump is still kicking on to drain but no water will release thru the hose, however if we take the hose off it will release water. what should we do?


... Hotpoint 24 in. HDA3740G Stainless Steel Built-in Dishwasher

I have a Diplomat ADP 8520 dishwasher (possibly SMEG manufacture) which will not stop trying to empty. There are 4 leds lit reading left to right and it beeps. I have read on some forums about pressing the programme button 4 times or holding it down for ten seconds to clear the fault but neither of these solutions work. I thought maybe that the drain was blocked but I put the pipe directly into the sink and it empties ok, problem is, it does not stop.


Fault is probably water in the bottom tray operating the anti-flood device. take bottom front panel off and mop out the water and it will work. if fault reoccurs then you have a leak ... Dishwashers

Dishwasher goes through part cycle with cold water, doesnt release the tablet then stops and the "Rinse and Hold" light and the "Intensive 70C" light flash and the washer bleeps then stops.


Hi.Check if the dishwasher is heating, if dishwasher does not heat, then either thermostat or element is faulty. Both get tested rteading Ohms at their terminals, if either one is open it must be replaced.If the detergent compartmen ... De Dietrich 18 in. VZ9456 Built-In Dishwasher

At the beginning the pressure washer was running but there was no power from the nozzle. I stop the gun trigger, remove the nozzle , it works for 1 minute and stop working again Now the washher pressure turns off on its own after 1 minute or less Honda 2400 psi


See attached link:\015\012http://www.wmpcs.com/index.php?main_page=page&id=14\015\012\015\012If you continue to have the problem you m ... Honda Karcher G2400HH-R Pressure Washer

I have a Simoniz S2800, it will only start with the trigger depressed to release the pressure and when it starts the engine seems laboured and there doesn't seem to be the ame pressure as it used to have, also if it isn't used after a min or so it will release water pressure from the bottom, do I need a seal kit or a pump kit to correct this problem.


Where is the unloader valve on these machines? ... Pressure Washers

Washer stops when handle released


Unloader valve not functioning properly causes pressure overload and stalls engine ... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0889 seconds