Having problems with your Pressure Washers ?

Diagram inside husky pressure washer wand - Pressure Washers


Answers :

Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Diagram inside husky pressure washer wand - Pressure Washers


... Pressure Washers

I have a Husky pressure washer with a Honda 2600psi engine. Problem is, no water will come from the pressure hose. I connected the water w/out the pressure hose and water flows thru strongly. I then connected the pressure hose w/out the wand and water flowed thru the hose fine. When I connect the wand and pull the trigger, nothing. I have replaced the wand and that was not the problem. Please help.


Check the quick disconnect to the wand these are spring operated and can get stuck ... Pressure Washers

Husky 500 2200 psi. starts and runs ok, but no pressure through the wand. hooked up garden hose to power washer turned water on and it comes through the hose ok, but start up and put wand on and no pressure.


... Pressure Washers

Husky pressure washer wand leaking - Pressure Washers


... Pressure Washers

I have a Karcher K3.48M electric pressure washer which used to shut off when you weren't using the cleaning wand. This no longer happens and there is alot of water running out of the bottom of the unit. (This didn't used ot be the case) I expect a leak somewhere inside the unit, but I'm wondering even more if there is a pressure switch which has failed that cased the leak. In other words, if I find and repair the leak and there is a failed pressure switch, it will likely only break again. I can'


Hi you will have a 8 digit number on a silver plate on the machine with a number like 1.141-470.0\015\012Then go to www.karcher.com then on the left click on Europe, then you ... Karcher PSI Electric Pressure Washer

I need diagram of inside wand of Husky powerwasher 1800


... Pressure Washers

My 1 year old gas powered Husky model HU80432 starts and runs fine but gets no pressure from the wand. Water is running freely through all connections and hoses so there are no obstructions, just no pressure, the water just shoots out in a thin stream for about 3 feet. I stored it inside for the winter so there were no freezing issues. What's wrong?


Lime/calcium build up in the pump.\015\012Pour a large amount of liquid TSP into the fresh water inlet and let it sit for two or three days, the longer the better.\015\012This is how I fixed my no pressure problem.\015\012Works gre ... Pressure Washers

Need the wiring diagram for the on off switch for husky 1800 pressure washer


... Pressure Washers

Powerstroke pressure washer PS171433 diagram for the gun wand


In European coupling ... Pressure Washers

Need a free diagram of Honda Husky 3000 PSI pressure washer that labels parts


... Honda Pressure Washer PSI 3000

Husky 3000 pressure washer, Axial Cam Pump Diagram , need to take apart to clean caked soap out. model# HU80432


... Pressure Washers

Turn water on then actuate wand trigger. Pressure washer leaks when wand trigger is actuated and has very low pressure/flow output. After releasing trigger the pressure cycles on - off at approx 1 second interval. I suspect that the plasstic oulet tube is leaking causing low pressure leak out of bottom when trigger is actuated and causes pressure switch to cycle when the trigger is released. Any Help? This pressure washer is approx 18 months old!


You gave a very close solution yourself for the problem. But other leakages can cause such symtoms.Forexample a leaking head or a leaking chemical inlet. These can be caused because the spill valve (pressure control valve) is stuck. When this valve s ... Karcher PSI Electric Pressure Washer

I have a Karcher 330 electric power washer. When connected and set to highest pressure (on variable wand) I get no motor action unless I reduce wand setting, then I get a little boost but not much. If I use high pressure conical wand I get high pressure sometimes, other times motor does not go and no pressure is delivered. I have replaced the high pressure hose.


Just wondering. have you tried it without an attachment to see what kind of pressure you get ... Karcher K2.26 Electric Power Washer

How to repair a hole in the wand tubing for pressure washer


My Honda ic2 ran greet, then all of a sudden it started to slowly shutting down,i restarted it. and it ran for about 5 min and shut down. i did this 3thee to four times do i need a gas additive or what ... Pressure Washers

Have a Husky Pressure Washer 2200 psi, HU80931. I don't have an owner manual. It has set for about a year. When I started the washer there was very little pressure. Did some cleaning and it was a little better, but now there is no pressure and I am having trouble keeping it started. Can you help? The washer was purchased at Home Depot and it has Briggs and Stratton the the washer too. Thank You, RJ


Look at eReplacementParts.com and the parts diagrams ... Briggs & Stratton Pressure Washers

I have an older Landa Pressure Washer. The burner is not working. Once I get the machine running and water flowing to the pressure washer, with the wand pressed, I flip the burner on switch....and nothing...I have no idea how to work on a pressure washer burner. I have been told it could be the igniter, but I don't know how to fix it if it is. Any help is appreciated.


Check for 12V at the igniter connector with the unit running. If you have 12V and no igniter it may be stuck or bad. Thrun the unit off and read continuity across the DISCONNECTED igniter plug / terminals to the igniter. No resistance = open ignit ... Pressure Washers

I have a power washer that needs a wand for the high pressure, the low pressure wand is part number PA6630GF. I need the part number and where tp urchase the high pressure wand.


... McCulloch FHH18A Electric Pressure Washer

Deville Excel Model # EXHA2425 Pressure washer I have a deville excel Model # EXHA2425 pressure washer. I went to the deville website (devap.com) which forwarded me to the dewalt site w/ exploded diagram below. I am having problems with intermittent pressure production. If I squeeze the trigger sometimes it will have pressure, somethings it will not. If I repeatedly squeeze, then release the trigger sooner or later I will get pressure. Someone on hear had told me it was a "bypass valve sticki


You\015\012need toput antifreeze in the out/outlet or/oil then start it up you are driing out the seals allways put away with repeating this step ... Karcher 2500 PSI Pressure Washer

What size are the o-rings on my Simoniz CL 11 pressure washer wand?


... Pressure Washers

Deville Excel Model # EXHA2425 Pressure washer. Is "unloader" the same as "bypass valve"? I have a deville excel Model # EXHA2425 pressure washer with a 5.0 Honda enginr. I went to the deville website (devap.com) which forwarded me to the dewalt site w/ exploded diagram below. I am having problems with intermittent pressure production. If I squeeze the trigger sometimes it will have pressure, somethings it will not. If I repeatedly squeeze, then release the trigger sooner or later I will get p


... Pressure Washers

If while pressure washing I let off the wand trigger it looses pressure and I have to turn of the washer motor and wait for the pressure to return.(seems like some kind of vapor lock problem)When the pressure returns I hold the trigger and restart the washer. If I let off the trigger we go through the same process again. this is a g3050


Hi and welcome to FixYa, I am Kelly. \015\012 This is most often caused by the bypass / un-loader valve located on the high pressure output side of the pump. The valve will either have a stem type valve with a knurle ... Karcher 2500 PSI Pressure Washer

I need a pump schematic diagram for a simoniz s2250 gas powered pressure washer


... Pressure Washers

My karcher pressure washer is switching on and off when the wand is not being used. the pressure should hold but it appears to cut in and out every 2 secs. the machine works o.k. when pulling the wand trigger but i think the pressure is slightly reduced.


Unfortunately these little units have this problem commonly, 9 times out of 10 it will be the plastic head on the unit will be cracked and leaking slightly... it builds up pressure then leaks out and tries to build up the pressure again ... Karcher K2.26 Electric Power Washer

No pressure to the wand. Motor runs and pressure gauge reads 4000 psi.Feels like no power in the wand Is a Honda pressure washer model #BEEX-2965HWCOMX.


... Honda Pressure Washers

Have no pressure from my Husky HU80432A power washer


... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1016 seconds