Having problems with your Pressure Washers ?

How much oil goes back into a Troy built quantum 6.5 hp pressure washer


Answers :

Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How much oil goes back into a Troy built quantum 6.5 hp pressure washer


... Pressure Washers

How much oil goes in a troy built 1903 pressure washer pump


... Pressure Washers

I have a sears pressure washer, model 580752300. The pump on the underside vibrated lose and broke a couple screws. It came off and the oil drained out. I replaced the screws and it's ready to go except I can't find out how much replacement oil to put back in. Sears has larger containers but won't tell you how much oil to put in. However, there's a pricey pre-measured container they want to make you buy. Anybody know how much oil goes in that pump?


... FAIP Non Marking Pressure Washer Hose 4000 Psi, 50ft. Length

New honda pressure washer maybe had it 2 years and only has about 3 hours on it, I was using it yesterday and it started fine and after running for about 10 min it shut down like i turned the kill switch, it has oil and gas but seems to have lost compression. It is a Honda overhead cam GCV 160, pressure washer is a Troy Built model


... Pressure Washers

I have a coleman pressure washer model # PW0912500 - What type of oil goes into the pump housing , how much goes in, and how often does it need to be changed ?


... Pressure Washers

I have a troy built 2450 pressure washer. The engine runs fine but I have no pressure out of the hose. Does the pump require that you put oil in it?


Do you live where it is cold in the winter? And did you winterize the pump this past winter if it is cold? They need to be winterized or pump damage can occur. ... Pressure Washers

How much oil goes into pump on a karcher 330m electric pressure washer????


... Karcher K2.26 Electric Power Washer

I have a troy built pressure washer 2200 psi. I let someone borrow it and when they brought it back water is spewing out the bottom. Do I need a new pump or what


... Briggs & Stratton Pressure Washers

Do you mix oil and gas with troy built pressure washer?


... Honda Black Max 2600 PSI Pressure Washer

Oil for Troy built pressure washer model 020207


... Pressure Washers

Troy built 2350 psi 2.0 gpm. pressure washer. starts onne then dies. will not start again. has briggs and straton motor. has been sitting up for the winter. have changed spark pulg. checked air filter that is clean, has oil and gas.


... Pressure Washers

Where do I put oil in a 3000psi 7 HP Troy Built Pressure Washer?


... Briggs & Stratton Pressure Washers

How much pump oil goes in a troybilt 2200 pressure washer?


... Briggs & Stratton Pressure Washers

How much oil do i need for a 6.75 troy built power washer with a briggs motor


... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

Oil is leaking from bottom of Troy Built pressure washer


... Briggs Stratton 198347gs Pump Assembly Kit For Pressure Washers

My troy built 2200 pressure washer was running fine but then shut off instantly I then noticed it had low oil I filled it but now it won't start


Pressure washer takes oil in two places:Pump oil is 20-30 weight SAE non detergent and comes half way up/ do not fill more than 1/2 way ... Briggs & Stratton Pressure Washers

Troy built 2550 pressure washer pump oil amount


... Briggs & Stratton Pressure Washers

How much oil in pump...Craftsman 2200 PSI pressure washer


Hello:Best to use NON DETERGENT 10W30. Be sure you fill the reservoir only 1/3 to less than 1/2 full. ... Briggs & Stratton Pressure Washers

Troy Built pressure washer starts up fine and idles nice. Start spraying and everything is fine for about 30sec to 1min then the engine just shuts off. Seems like pressure is building up and choking the engine out. If I dont spray it will idle all day long. I have cleaned the unloader area, still shuts off. I have the pump off the machine, what should I do? Model number 020208 Troy Built. Rev # 01


... Pressure Washers

Where is the oil plug located on a 2450 psi troy bilt pressure washer


... Pressure Washers

My Troy Bilt power washer (using Honda GCV160 engine) has no pressure coming from the pump. I checked the water flow, everything seems fine. I believe the pump needs oil added, however, I can't seem to firgure it out (how to add oil to the pump). I did notice that previously, I used to see drops of oil coming from under the pump. I I have a bad seal, can I add oil and test the pressure before I change the seal? Please advise.


I had a similar problem. Turns out I had left the hose disconnected and some sort of wasp built a paper type nest inside the washer tube that the hose connects to. I had to take the pump off and take apart and then cleaned it out with a screw driver. ... Honda Black Max 2600 PSI Pressure Washer

My pressure washer leaks water out the back form some kind of valve that has a hole in it. the pressure washer will flow pressure but not as much as it did.


... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started. I have the same problem. Water flows thru the pump when not running, but no flow or goes in by-pass mode when I start the pump. The pump being Troy Bilt Model 020296-01. I replaced unloader valve even. Anything else I can do?


You replaced the unloaded valve. Are you positive you have the unloader screwed to pressure and not turned the opposite way? You will have no pressure if it is adjusted wrong. One other thing I have encountered is that the unloader has a ball bearing ... Pressure Washers

I think I added too much oil to my pressure washer. It lost pressure after about 20 minutes, then smoke came our where the exhaust area is. I immediately turned it off. Then I noticed oil dripping from the oil filter. What do you might have happened and what should I do?


Drain the oil until the proper level is reached....let the unit sit for awhile until cool and then remove spark plug and clean it....i think it should be just fine....good luck ... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

Troy built pressure washer will not run unless the choke is out


... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0935 seconds