Having problems with your Pressure Washers ?

I have a G2500VH pressure washer that has started to pulse when the trigger is squeezed. This happens if I use the 0,25, and 40 degree nozzles BUT if I use the one for low pressure(detergent use) it will hold pressure fine. I have changed the unloader valve, checked all the valves and seals ad they seem to be fine. What could be the problem?


Answers :

Do you mean pressure on and off with the hp tips and smooth and steady with chemical tip?
Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a G2500VH pressure washer that has started to pulse when the trigger is squeezed. This happens if I use the 0,25, and 40 degree nozzles BUT if I use the one for low pressure(detergent use) it will hold pressure fine. I have changed the unloader valve, checked all the valves and seals ad they seem to be fine. What could be the problem?


Do you mean pressure on and off with the hp tips and smooth and steady with chemical tip? ... Pressure Washers

I have a HD 2701 DR pressure washer that starts and runs fine and usually works fine the "first" time but if you let go of the trigger and then try to use it again you just get a trickle out of the end of the wand. Usually if you hold the thing open for a while it will kick in (sometimes it takes forever...). Any ideas? It sounds like some of the "unloader valve" problems are similar but I do not see an "unloader valve" in the parts lists for the 2701...


... Karcher G 3050 OHR Gas Pressure Washer

Karcher K3.91, lost some pressure and pulsing when trigger is release. stripped it down and checked all six valves and there all sealing as they should. i took apart the unloader valve cleaned and inspected and thats fine. there is NO water leeks anywhere or oil. preasure washer is 2 years old and gets used once a week for ten minutes. i really dont understand why its playing up


... Pressure Washers

Model 01902 2350 psi . engine runs fine , sprays out nozzle but lower pressure and water sprays out plastic elbow on relief valve , that is supose to **** in soap if used , cant hold finger over spray from elbow , high pressure , took apart relief valve and plastic valves all orings are ok , brass pump seals look ok , all back together , still blows out elbow . ?? plastic spools were out by somebody else , not sure if they are in right , cant find picture to compare .


It sounds as if the non return valve in the elbow is the wrong way around .The o-ring normally goes in first then the ball then the spring. Try it and good luck. ... Pressure Washers

My Troy Bilt power washer (using Honda GCV160 engine) has no pressure coming from the pump. I checked the water flow, everything seems fine. I believe the pump needs oil added, however, I can't seem to firgure it out (how to add oil to the pump). I did notice that previously, I used to see drops of oil coming from under the pump. I I have a bad seal, can I add oil and test the pressure before I change the seal? Please advise.


I had a similar problem. Turns out I had left the hose disconnected and some sort of wasp built a paper type nest inside the washer tube that the hose connects to. I had to take the pump off and take apart and then cleaned it out with a screw driver. ... Honda Black Max 2600 PSI Pressure Washer

I have a simpson 3000 belt drive w/ a honda moter.runs great and well taken care of. delivers good pressure, but when not holding the trigger a small burst of air/water shoots out from thehigh pressure overload about every 15 sec. i changed the springs on the system and it checked out o.k. is there an adjustment on the bottom of this overload valve? please return a.s.a.p. Thanks, Pettke deco.


I worked at a tool rental store during my college days and rented a similar unit quite often. I am puzzled about the high pressure valve that you describe. If I recall correctly, the units that we rented had a high temp relief valve. The springs wer ... Simpson Pressure Washers

Briggs and Stratton pressure washer will not start. I have a 6.75 hp pressure washer that is only a year old. when I pull cord it turns over but does not start. I changed plug and checked it, I have spark when pulling. I have 40-50 psi of compression when pulling also. gas was drained and is brand new. it was working fine last time it was used. I have tried starting it without the water line or spray wand hooked up and no difference. After about 10 or 15 pulls, can smell gas when I am trying to


Hello dave, the problem is compression to low,you need 60 to 130 lbs to run engine,check for blown head gasket,or bad rings,or a stuck open valve,hope this helps,, ... Briggs & Stratton Pressure Washers

Low Pressure with no hose attached, pressure is good, attach hose without wand and pressure drops 50%. Have had pump apart 10 times, have checked bypass valve, have even removed bypass and filled passage way so water could not bypass wihout any change. Am down to thinking pump casting is cracked allowing bypassing to happen. Does each of the three piston chambers have a check valve so one piston is not pumping back into another piston chamber?


I worked at a tool rental while attending college and had the opportunity to work on a variety of pressure washers, however, they were of the commercial type. Commercial washers are slightly different in that they usually have seperated components fo ... Karcher 2500 PSI Pressure Washer

My Karcher 4000 SHR Pressure Washer pressure pulses when operating. I have checked with Karcher Technical Support and all their trouble shooting procedures except checking the unloading valve. Where is this valve, how do I get to it and how do I lubricate it?


It sounds like your unloading valve is crudded up with mineral deposits and stuck in a partway open state. look for a plastic cover with a silver snap on top; pry off the silver snap and lift off the plastic cover; next remove the two screws on the ... Honda Karcher G4000RH Pressure Washer

We have a Katcher HDS 3.5/30-4 M Ea. Was using it, stopped using it briefly in the middle of a job, pulled trigger again, and there was a lack of pressure. Went to the machine to troubleshoot. The "engine indicator light" is on. Checked the temperature of machine: fine. Water intake: fine. We have not been running it at high temperatures, but about 50 degrees C. The pressure was at about 2300 PSI before it stopped. Any ideas?


... Karcher Pressure Washers

Northstar Hot Water Pressure Washer (model #157322) While using the pressure washer the safety relief valve activated venting steam and hot water from it... I immediately shut it down and let it cool down. After it was cool, I turned on the water supply again and the relief valve was still spewing water from it. My neighbor said it was probably the "unloader" valve was stuck or damaged. I called around my area and it seems as though no one services my pressure washer.. Is there a manu


... Pressure Washers

I recently replaced the water seals, V-packing & all six check valves in a CW-3504-4MGH pump on a MiTM 3504 pressure washer that had very low pressure. Usually this would fix most pressure problems on most machines, but in this case it had little to no effect. I suspect that the unloaded is the culprit in this case, but since I have had little experience in repairing unloaders (let alone adjusting them). I would appreciate feedback from anyone that has experience in this area. Thanks


Check the wand tip for a tiny piece of debris like a tiny rock or something stuck in the tip. ... Mi T M Pressure Washers

My pressure washer is bogging out and shutting off. It will run fine for a bit then it starts sputtering and shuts off. I changed the oil right before this started happening and yesterday i changed the sparkplug and it seemed to be working fine until I used it today on the driveway.


SOUND LIKE FLOAT IS STICKING ... Dewalt 3800 PSI Pressure Washer

The motor is running fine and some pressure is coming out but not like it should. I used it a couple of days ago and it could peel the paint off a car and now it will hardly knock any dirt off my deck. What could be the problem. Again there is pressure but not like there should be. I have checked all nozzles and connections and checked the filter. I put a fresh oil job in it.


Sounds like the bypass valve is stuck. You need to locate it and lube it ... Honda Pressure Washers

North star petrol pressure washer. working fine, then no high pressure, checked water feed, water filter , pressure relief valve and gun nosall well work sometimes and keep working, when you release the trigger and try in again the pressure gone again. please help, many thanks, richard


Sounds like the regulator is sticking or is airbound. loosen the water connection and then tighten it back. Could also be that the trigger gun is faulty or needs adjustment. Hope this helped ... Karcher 2500 PSI Pressure Washer

How to fix/grease an unloader valve on yorur pressure washer .I pull my trigger on my pressure washer gun and it clicks with water stream coming out then goes to high pressure.this is a kacher reman unit.I was wondering if this is normal or does it constantly hold high pressure


... Karcher 2500 PSI Pressure Washer

I have a Northstar pressure washer powered by a honda GC160 engine. The last time i used it, water leaks from the bottom of the unit, whether it is running or not. When running, the pressure is fine. I have felt underneath and it appears that the water is coming from the second opening from the rear. Is there a pressure relief valve there. I have a manual but cannot find any descriptors for underneath the motor.


This is a piston seal issue. You can get a kit to rebuild the pump. ... Comet AXD 3020 G Pressure Washer Pump

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started. I have the same problem. Water flows thru the pump when not running, but no flow or goes in by-pass mode when I start the pump. The pump being Troy Bilt Model 020296-01. I replaced unloader valve even. Anything else I can do?


You replaced the unloaded valve. Are you positive you have the unloader screwed to pressure and not turned the opposite way? You will have no pressure if it is adjusted wrong. One other thing I have encountered is that the unloader has a ball bearing ... Pressure Washers

I 've not used my Karcher Pressure Washer for over a year. I tried to use it but it will not start. I've changed the fuse. I've checked the water outlet, but it will not start up. What is the problem with it?


... Karcher K 2.27 1600psi Electric Pressure Washer

I need to check the unloader valve on my Karcher 3000psi pressure washer. I was directed to your site for help. I just need to know what to unbolt to get to the valve.


... Pressure Washers

How do I clean the unloader valve on a Karchner model G2600VH Cannot get steady pressure from the outlet of the nozzel have clean filter checked for leaks and replaced all nozzels still having issue with flux in pressure.


Check the tips and Videos at http://www.ereplacementparts.com/karcher-2600-11944040-pressure-washer-parts-c-33388_33389_34001.html ... Karcher 2500 PSI Pressure Washer

Having problems with Miele G844-SC Plus Novotronic WIll not get through a full cycle of any type except Rinse and Hold. Have used vinegar, cleaned all accessable parts, checks filters and tubes, water pressure etc....can you help?


... Miele Dishwashers

I have a troy built power washer powered by honda. It runs for 10 - 15 minutes and then dies. I have replacced the ignition coil, spark plug, rebuilt the carburetor, checked fuel flow and placed the unloader valve and it still dies. Once it dies and the pressure is released it repeats the problem. Any suggestions?


... Honda Pressure Washer PSI 3000

I have a Karcher 3500 hd with a 2.1 head. Machine has always worked well but lately it has been pulsating. High pressure then low... repeat. I have checked valves and they seem fine. Any advise would be great thx.


Sounds like your seals are going , they sell a rebuild kit for it and it is relatively easy to install ... Karcher G3025OH Pressure Washer

INDESIT IDL505 DISHWASHER(2nd hand working fine for 3 months) started to notice some light/slight streaking, misting especially glasses(annoying but not to much of a problem) then about two weeks later heavy streaking,glasses totally misted completely did have a brief problem with water inlet solenoid but checked it and its working properly (only malfunctioned once) i refilled the salt container and put on a simple wash and found that it used about half the salt in the container,changed the hard


Maybe the machine got a leaked inside.. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1378 seconds