Having problems with your Pressure Washers ?
Hot shot pressure washer overheating water
\015 The water gets to hot and melts the hose. thermostat was replaced still does the same Hot shot brand\015
Answers :
You may have a stuck fuel solenoid valve normally located by the fuel pump i am a pro at this feel free to tell me the devices your unit may have pressure switch flow switch and thermostat normally are connected in series for burner to come on they all must connect.if u disconnected fuel solenoid connector and burner stays on while your squeezing the trigger you need to replace the solenoid valve it about 20.00
Repair Help & Product Troubleshooting for Pressure Washers
Tips for a great answer:
- Provide details, support with references or personal experience .- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Hot shot pressure washer overheating water
You may have a stuck fuel solenoid valve normally located by the fuel pump i am a pro at this feel free to tell me the devices your unit may have pressure switch flow switch and thermostat normally are connected in series for burner to come on they a ... Pressure Washers
Hotshot over heating - PressurePro Pressure-Pro Hot Shot Series 4000 PSI Hot Water Pressure Washer
There r three devices which can cause overheating.1)-thermastat(stuck in close circuit2)-pressure switch and or flow switch stuck in close circuit. 3)-fuel solenoid stuck open located at fuel pump ... PressurePro Pressure-Pro Hot Shot Series 4000 PSI Hot Water Pressure Washer
Northstar Hot Water Pressure Washer (model #157322) While using the pressure washer the safety relief valve activated venting steam and hot water from it... I immediately shut it down and let it cool down. After it was cool, I turned on the water supply again and the relief valve was still spewing water from it. My neighbor said it was probably the "unloader" valve was stuck or damaged. I called around my area and it seems as though no one services my pressure washer.. Is there a manu
... Pressure Washers
Does it hurt a pressure washer to run hot water thought it went they hook up the water for outside to hook it to the hot water i did not no it and i hook it to the pressure washer
Most pressure washers have packings that can sustain a temperature of 140 degrees although it as strongly not recommended since the pump head heats up when in bypass mode(triggergun closed)best rule for pressure washer is never leave the trigger clos ... Karcher 2500 PSI Pressure Washer
2-yr old troy-bilt pressure washer with honda gcv160 engine. seems to run well, but when trigger is pulled get full pressure for less than 5 seconds before reducing to house water pressure. when left running, looks a black plastic pressure relief valve starts blasting hot water. appreciate whatever insight you can give. Thx
It sounds like an air lock. Try this: With the machine off, connect the hose to the washer and let it run for several minutes to get all of the air out of the hose, and to purge any air out of the pump. Shut off the water, and connect the high pre ... Briggs & Stratton Pressure Washers
My kitchenaid dishwasher will not complete a washing cycle. the water heating seems to be staying on all the time. could my heating element be shot. the water seems hot when i open the dish washer during the cycle but it is connected to the hot water supply line. thanks
... KitchenAid Dishwashers
I have a northstar pressure washer hot water. they say the coil is no good anymore. Is there a way to bypass the hot and go only cold water?
... Northstar Gas Powered Wet Steam & Hot Water Pressure Washer 3000 PSI
Two problems please: craftsman 2150psi briggs and stratton engine washer, will not start when hot. and secondly, i was washing with regular pressure, then noticed a pressure drop at the nozzle, then the unit shut down. no water leaks at the manifold. water supply was strong. any ideas?
Nozzle dirty, clean out with small diameter wire. ... Pressure Washers
Hot water coming out of a cold water pressure washer
This sounds like a heat transfer problemYou should check that the oil reservoir for the pump has oil in it. It sounds like it may be low. Also, if it is a gas model, the engine oil may be low. Remember the pump oil re ... Porter Cable Pressure Washers
Pressure Once I have the powerwasher started and going (water to it before starting) i can't get it to go to full pressure it will prime up like it's going to go to full pressure give me just a shot of full pressure then go back down to probably half pressure and remain there then prime again for a second then back a coninues cycle! Maybe there's a seal or something somewhere I should look at. Hose and pressure from house is good, the seal whee the hose attaches to the bottom of the washer is ne
This is usually a problem with the "dump valve" defective in not being able to hold the pressure but only able to release it prematurely as it should only do so when to much pressur is built up inline. Only recommend qualified pump tech. But check pu ... Coleman Pressure Washers
Low hot water pressure in old whirlpool washer forever to fill
If you have verified that it takes longer than 120 seconds to fill with water then you need to replace your inlet valve. You might be able to get away with just cleaning the screen but you should probably replace it. pn 8531670.\015\012However ... Whirlpool 24 in. GU1200XT Built-in Dishwasher
Brand new Northstar hot water pressure washer, 2000 psi, electric and Diesel fired burner. The burner will not come on??? It works ok as a cold water unit but the burner will not fire even with the Heat switch on and fuel in tank?? What could cuse this?
... Northstar Wet Steam & Hot Water Pressure Washer with Honda Engine 3000 Psi, 4 Gpm
Won't pump out water - Cam Spray ST Series 3000 PSI Hot Water Natural Gas Pressure Washer
... Cam Spray ST Series 3000 PSI Hot Water Natural Gas Pressure Washer
My Diesel Fired Burner on my Hot Water Pressure Washer leaks diesel below the Hot box. It has new diesel from the gas station..
... Shark Helmet Shark Professional 3000 PSI (Gas Hot Water) Pressure Washer W Honda Engi
My honda pressure washer doesn't build pressure and the water gets hot
... Honda Pressure Washer PSI 3000
I have a northern 3000 psi hot water pressure washer everything works but the burner will not fire up to heat the water
If it gettin diseal to nozel it ur photocel r thermostat ... Northstar Gas Powered Wet Steam & Hot Water Pressure Washer 3000 PSI
My gas powered pressure washer runs great. But within 25sec. of spraying the water, the engine gets very hot and quits. Any ideas what to do??
... Briggs & Stratton Pressure Washers
Water Diver Series pressure washer, model WGV1721 shut off when running and the pump gets so hot I can't keep my hands on it.
... Briggs & Stratton Pressure Washers
I have a honda 2600 pressure washer. After running fine for a couple of seconds the water will stop flowing out the tip. It is receiving water,but will not flow it to the pressure hose. I even disconnected the pressure hose and no wate was flowing out. When I shut the pressure washer off it would then flow water to the hose again. Please help
This is a symptom caused by a sticking Unloader valve. The Unloader valve is inside the pump outlet body under the large black knob. \015\012Example picture : ... Honda Black Max 2600 PSI Pressure Washer
Just turned on my pressure washer model 580 676630 and as soon as i pulled the trigger to start spraying water shot out of a coupling underneath. It seems as if a heal has ruptured. Can this be repair
... Craftsman 2550 MAX PSI Briggs & Stratton Powered
Need parts I need to order water manifold for pressure washer. Where can I find a parts listing? (16 hp/w hot tank)
Find brand name go to website ... Northstar Pressure Washer 3000 PSI
Heater will not lite - Northstar Gas Powered Wet Steam & Hot Water Pressure Washer 3000 PSI
Donnie I have same problem, did you get it resolved? ... Northstar Gas Powered Wet Steam & Hot Water Pressure Washer 3000 PSI