Having problems with your Pressure Washers ?

Pump won't come on. - Pressure Washers


Answers :

If water is coming out of wand then you may have obstructed check valves..this occurs when the inlet has no strainer,check valves normally behind plugs that look like screws.
Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Troy Bilt power washer (using Honda GCV160 engine) has no pressure coming from the pump. I checked the water flow, everything seems fine. I believe the pump needs oil added, however, I can't seem to firgure it out (how to add oil to the pump). I did notice that previously, I used to see drops of oil coming from under the pump. I I have a bad seal, can I add oil and test the pressure before I change the seal? Please advise.


I had a similar problem. Turns out I had left the hose disconnected and some sort of wasp built a paper type nest inside the washer tube that the hose connects to. I had to take the pump off and take apart and then cleaned it out with a screw driver. ... Honda Black Max 2600 PSI Pressure Washer

I have a Comet BXD 2525 G pressure washer pump which is giving me some problem. (Maybe) I hook the water up to pump and the pressure hose up to the pump, turn on the water and the water sprays out of the water connection at the pump. I check the hose to see if it was clog ok and the next was a the water connection ok. It's like the water is not going int the pump. When i start the pressure up the water come out of gun but no pump running like it should. The next thing i was going to look at i


The water inlet needs a gasket like all hose connections. If its gone the pump may be starving for water. ... Comet Pressure Washers

Briggs and Stratton Troy Bilt gas pressure washer one year old. I can get water thru pressure washer and bleed the air, water comes out the hose just fine until I start the pump. Then, I lose all water flow. Pump runs fine but when it's running, no water goes through.


... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

I have a campbell hausfeld 2450 pressure washer with water coming out of a brass hose nozzel right next to where you screw the high pressure to the pump as soon as you turn the water on from the house, start it up and high pressure comes out of it and the hose about half pressure, any ideas?


This is called the chemical injector which enables you to insert the hose for you to dispense the soap and or chemical by utilizing a soap nozzle .apparently inside this barb you will find a ball a spring and a o-ring,find the replacement parts or ki ... Campbell Hausfeld Pressure Washers

Karcher 3100 pressure washer, motor runs fine but when I squeeze the trigger on handle, high pressure pump won't come on unless I remove tip and water is coming out of wand without restriction. Help anyone have any ideas? It did come on once but when I let go of trigger it wouldn't come back on.


... Alfred Karcher Quick Connect Nozzles 2600 3100 Psi 5 Pack

No high power water pressure coming out of my model #580.768030 pressure washer. The same pressure comes out when the pump is turned off.


You should dismantle and clean the manifold from the pump , it is sticking. Common ... Comet BXD2527 Pressure Washer Pump

My coleman powermate 2750 pressure washer locks the engine up when the trigger is pulled. after a few seconds you can restart it.it comes up to good pressure but kills the motor. Some have told me they thought it was teh pump, but the sprays a little. I would think if the pump was bad it wouldn't spray at all? Comments?


All i can say is its not a good mechine I owen and repair washers and pumps and use them in line of business thats all i can tell you sorry ... Coleman Pressure Washer PW0881800

We want to replace the pump to our DEWALT DP3750 pressure washer and can not ge tthe pump to come off the engine. how do you get it to come off?


... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

I have a ANNOVI pressure washer and I can not seam to get the engine apart from the pressure pump. All bolts are removed and the bludy thing will not come apart. The lock nut on the drive is not even


There may be no good news for you. Once those hollow shaft pumps seize to a engine shaft, they can be real buggers. In fact, they can be impossible. But before you give up and completely destroy the pump to remove it from the shaft -- the ... Pressure Washers

Troy Bilt pressure washer 2600psi. Engines running fine with supply line, wand, and pressure line hooked up but no water or pressure is coming from pump. pressure line is limp. What is the problem?


... Troy-Bilt Pressure Washers

Dear Sir?madam, I bought a CV-240 4 MBC HONDA PRESSURE WASHER , 2400 PSI , 5.5HP, It is 4 stoke overhead, cam single cylinder , October, 2010 from NATIONAL HARDWARE SUPER CENTRE – GUYANA. I used this equipment sparingly during this year. I have 2 – 450 gallons plastic water tanks to supply the pressure with water. Recently, water is not coming out through the pressure hose. I talked to a technician, and he opened the water pump and there is some white plastic valve, one was broken and he repl


... Karcher 2500 PSI Pressure Washer

Oil in pressure washer pump gray and coming out of pump


... Simpson Pressure Washers

Pump Issue I have a john deere pressure washer. I hook the hose up to it, rurn the water on and no water comes out of the wand. I started the engine briefly and pulled the trigger on the wand and still nothing. The model number of the pump is Annovi Reverberi SJV 2.5G24-1. I can't seem to find any info on the G24? There is info on the G27-1. Not sure what to do here? Please help.


... Pressure Washers

Pump wont come off - Comet GXD2527G Pressure Washer Pump


... Comet GXD2527G Pressure Washer Pump

I have a Pressure Washer VR2500 , 6.5 horsepower / 2500 PSI number on side 123K12-0134-E Residential - Excell. I do not know which is the oil drain plug for the Pump on the bottom. There is an Allens Wrench plug on the side. However when removed nothing comes out. There is also an Alans Wrench like plug towards the back, that does not want to come out. Which one is the correct plug and do you have a picture as I could not order an Owners Manual on-line? Please Advise!


Hi and welcome to FixYa, I am Kelly \015\012First here is the owders manual: \015\012http://www.excellpressurewasher.com/documents/p ... Comet GXD2527G Pressure Washer Pump

When i turn on my k499m pressure washer the motor seems very week and the pressure is non existant has anyone ever come across this problem before i havnt tried anything to fix it yet but the water is flowing into it ok it just seems as if their is something wrong with the motor or pump


I have come across this before, it can be that the motor has burned out and in that case it can be better to purchase a new machine. \015\012\015\012It could also be the capacitor which is not a very expensive item to replace. What the ca ... Karcher Pressure Washers

Husky HU 80522 pressure washer - some pressure to the spray gun. water coming from the pump goes straight to the sifon hose used for detergent. Can this line be clamped of if not used?


... Pressure Washers

Husky HU 80522 pressure washer - some pressure to the spray gun. water coming from the pump goes straight to the sifon hose used for detergent. Can this line be clamped of if not used?


This unit has a Faip pump on the unit, no water should come out the chemical injector. The chemical injector can be closed off with no problem by installing a plug where the chemical injector hose bard is currently located.You can also replace th ... Pressure Washers

I have a union power petrol pressure washer up1-50 I am having problems with a fine spray of water coming from the 1st brass screw on the end of the pump and keep loosing pressure


I have the same hair line crack so water pushes out the top. Can the part just be replaced ? ... Pressure Washers

The model of the Honda Pressure washer is VR 2522 and for the pump is A07908, the one you give me was for pump a14527 which is a different make. still trying to figure out the solution and where the leaks is coming from, please help?


... Honda Pressure Washers

Troy bilt pressure washer series 675 no water comes out the pump


Stuck valves inside the pump will stop water flow ... Pressure Washers

My Karcher K3.48M pressure washer remains in the low pressure mode even when I return the pressure nozzle to the high pressure position. How can this be corrected. The pump seems to build up the pressure because when I release the handle the pump motor stops. This is a fairly new pump which was purchased in the latter part of last year(2010). Could this have been caused by the detergent I have been using which is an automotive shampoo? Please help I love this washer and for the times that I u


... Karcher PSI Electric Pressure Washer

Cat pump 3200 psi problem- plz help! I hook up the hose and no water will come out of the pump out let with or with out the hose the pressure waser hose hooked up!


... Caterpillar Cat Pump Pressure Washer Pump 3SP30G11

Pressure washer has no pressure coming out


I think yor hot water softened one of the pressure seals and has allowed it to buccle. This will drop the pressure away from the pump. It will require new seals to be fitted and the cost is close to $200. ... Pressure Washers

I can't remove the pressure washer pump because the Engine Adaptor, part # 95165 will not come off. Anyone know how to remove it? The model is 580751651.


... Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0866 seconds