Having problems with your Pressure Washers ?

I disassembled the wand of my S1900 Simoniz pressure washer and can't figure out where the spring goes. I know it has to do with the trigger.


Answers :

Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I disassembled the wand of my S1900 Simoniz pressure washer and can't figure out where the spring goes. I know it has to do with the trigger.


... Pressure Washers

Whirlpool DU927QWDG1 Hi, The problem I'm having with my dishwasher pertains to the door cover for the area I place the soap. There is a small spring which helps the door pop open to release the soap when washing. I cant figure out how to place the spring so that the pops open.....right now when I run the unit the door stays latched and the soap doesn't get dispensed. Any ideas on how to repair this or where I could maybe get a parts manual??? Your expertise will be greatly appreciated!!!!


... Whirlpool GU2400XTP Built-in Dishwasher

I was replacing the hose and a little spring popped out of somewhere. The spring has a clear plastic end also. The whole thing is about an inch and half long. I believe it goes with the yellow trigger handle but cant find where it goes


... Karcher K2.26 Electric Power Washer

How to re-assemble Simoniz S1900 Spray gun - Can you show me how to put the spray gun back together? I have 2 springs-don't know where they go??


... Pressure Washers

I cant figure out how to operate my simpson cascade 52 021 dishwasher it seems simple but it wnt work i dont know if its broken or if it just wont work


... Dishwashers

Where does the spring go in the wand?


... Pressure Washers

Turn water on then actuate wand trigger. Pressure washer leaks when wand trigger is actuated and has very low pressure/flow output. After releasing trigger the pressure cycles on - off at approx 1 second interval. I suspect that the plasstic oulet tube is leaking causing low pressure leak out of bottom when trigger is actuated and causes pressure switch to cycle when the trigger is released. Any Help? This pressure washer is approx 18 months old!


You gave a very close solution yourself for the problem. But other leakages can cause such symtoms.Forexample a leaking head or a leaking chemical inlet. These can be caused because the spill valve (pressure control valve) is stuck. When this valve s ... Karcher PSI Electric Pressure Washer

Pressure washer Briggs and Stratton 020375 shuts down after i release trigger on wand


... Briggs & Stratton Pressure Washers

16 year old GE built-in dishwasher, model GSD900. Springs that prevent front door from falling disconnected. ALL parts APPEAR to be in good condition. I say appear in good condition because I don't know what they are supposed to look like. But I see nothing obviously broken. The 2 springs appear intact. The connecting cable is good. However one of the 2 springs is shorter than the other. It may be shorter because one is supposed to stretch to the other side of the dw? So number 1


... GE Dishwashers

Detergent dispenser spring door is either missing the spring or broken. In any case it opens but is no longer spring loaded. I can't figure a way to remove the assembly unless I have to take off the front cover. Any ideas?


Door just pulls off, you will require a new door, spring & possibly a catch. Spring fits onto pin on door and other end onto pin on holder, then fold spring on its-self and re-instate onto runners/slide. Paul Winn Appliance Services. (Cumbri ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a Husky pressure washer with a Honda 2600psi engine. Problem is, no water will come from the pressure hose. I connected the water w/out the pressure hose and water flows thru strongly. I then connected the pressure hose w/out the wand and water flowed thru the hose fine. When I connect the wand and pull the trigger, nothing. I have replaced the wand and that was not the problem. Please help.


Check the quick disconnect to the wand these are spring operated and can get stuck ... Pressure Washers

I have a Honda GC160 5 horsepower power washer with 2400 psi. When its cold it is easy to start but after it has been running for a while the only way to start it is to have the water shooting out of the wand. Once it is hot and running if i stop the stream of water (release the trigger on the wand) then the machine shuts off. It seems like the only way to keep it running is to constantly have water running through the wand. Please help


... Pressure Washers

We have a Karcher G2500VH pressure washer. If you start the engine with the trigger pulled on the spray wand it will run at full pressure until you release the trigger. after that, when you pull the trigger it will not have any more pressure than the water hose feeding it. Does it have an internal unloader valve? What is the part number?


Hi, Karcher calls the unloader valve a spill valve, this is a link to a full drawing/parts listing , and your fault description might well be a sticking /seized unloader(spill ) valve hope this helps ... Karcher 2500 PSI Pressure Washer

If while pressure washing I let off the wand trigger it looses pressure and I have to turn of the washer motor and wait for the pressure to return.(seems like some kind of vapor lock problem)When the pressure returns I hold the trigger and restart the washer. If I let off the trigger we go through the same process again. this is a g3050


Hi and welcome to FixYa, I am Kelly. \015\012 This is most often caused by the bypass / un-loader valve located on the high pressure output side of the pump. The valve will either have a stem type valve with a knurle ... Karcher 2500 PSI Pressure Washer

Door mechanism door has 2 springs on each side, on the right the spring works on its own. But come to the left side and it has a long belt type piece of metal,the spring and a hook type piece that makes up how the door opens and closes.this left side has come apart and dont know how it goes together,therefore the door just drops very sharply to the dismay of my partner.plz reply to [email protected]


Wind metal strap around plastic bush and hook above hinge ... Candy 24 in. CD622 Free-standing Dishwasher

Lack of pressure after releasing the trigger on the wand


Hello awcockerill:This sounds like the bypass (unloader) valve is sticking. Here is a diagram of your machine's pump. On page 2. ... Karcher 2500 PSI Pressure Washer

Karcher K 3.68M Electric Pressure Washer. Wand trigger Locks Up.


Sounds like the pressure valve is broken thats why you cant depress the trigger , the valve is on the pump , i would suggest taking it to a repair shop as they are fiddly things to fix ... Karcher PSI Electric Pressure Washer

Let go of wand trigger pressure will not come back


Spill valve is stuck and needs to be cleaned and greased common problem....also check all connections for blockage in line ... Karcher 2500 PSI Pressure Washer

PWER WASHER RUNS PERFECT, WHEN WATER COMES ON, IT STALLS. BUT IF YOU PULL TRIGGER BACK ON WAND, THEN SPRAYER WORKS. THE MINUTE YOU LET GO OF TRIGGER, IT STALLS OUT.


Hi you have got a fault with the unloader it's not unloading so its going a bove the 13amps and knocking the thermol overload out or blowing a fuse you could cable tie the trigger open or get a new unloader kit costing about £70.00 regards ... RTO 1800 PSI Pressure Washer

De dietrich dvf300ju2 needs door spring replacing - I have the spring but cant find it to replace.....


To replace the spring you need to pull the dishwasher out and look on the sides. You might also have to lay it on its back to see the springs.. ... De Dietrich 23 in. DVF110J Built-in Dishwasher

I have a dishwasher dw918td and have lost the spring action for the door . i would like to know how to replace the springs as required thanks.


The door springs are located behind the lower kick plate. Just remove the four screws that hold the panel on you will see the springs and cables that help hold the door up. ... Dishwashers

I have a DPH3800 Dewalt pressure washer and the soaper isn't working properly. Right tip is being used but when trigger is not pressed it puts water into the bucket. When trigger is pressed it does **** some solution into the hose but very little and very slow. The valve is opened all the way. I know my former partner used bleach in the system which I read in the manual is a no no but it did work at the end of last season. Any ideas?


How is the pump connected on a john deere 3800 psi. i took out the 4 bolts and drained the oil. pump is stuck to cam. how does it come off? ... Dewalt 3800 PSI Pressure Washer

Trigger gun for gas Karcher pressure washer is missing spring or whatever allows the trigger to work...can anyone help with parts advice?


... Pressure Washers

Door dropped Opened door on my FDB421RFR and a loud cracking noise occurred - now the door drops quickly. I guess the spring(s) have broken - does anyone know if the spring is on the rhs looking at the front? I sure hope so, I can probably access that side without pulling the unit out! Is it good to spray these with WD-40 or do they just age anyway?


... Frigidaire 24 in. FDB421RF Built-in Dishwasher

My karcher pressure washer is switching on and off when the wand is not being used. the pressure should hold but it appears to cut in and out every 2 secs. the machine works o.k. when pulling the wand trigger but i think the pressure is slightly reduced.


Unfortunately these little units have this problem commonly, 9 times out of 10 it will be the plastic head on the unit will be cracked and leaking slightly... it builds up pressure then leaks out and tries to build up the pressure again ... Karcher K2.26 Electric Power Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0818 seconds