Having problems with your Admiral 24 in. DDB1501AWW Free-Standing Dishwasher ?

I Have 3 problems with my dishwasher, my dishes are always coming out with food and grit. I've tried numerous soaps and powders, the motor makes a very loud loud every time it's used. and the latch works but I can opent the door mid cycle it doesn't stop water sprays everywhere


Answers :

Regarding the problem about dishes coming with food and grit - it is possible the wash water is getting contaminated with stuff that should normally be sucked out by the drain pump up in the dishwasher. This is linked to the accumulator and chopper part of the wash system. The food particles are collecting in the accumulator and mixing with the wash water. Normally the chopper should expel it out through the drain wash system. You will have to disassemble the accumulator and check what is wrong. See the diagram - parts 7 and 8,
\015\012
\015\012Now regarding the motor noise - this model has 2 motors - one for wash and one for drain. Which motor is noisy will depend on whether this comes during the wash cycle or the drain cycle. Usually it is the bearing that is faulty. You can replace the motor by checking the previous diagram.
\015\012
\015\012Regarding the door switch - I am not clear what the problem is. Unless you pause the cycle on the panel I would not open the door. The unit works with 2 door switches - both must be closed (when you shut the dishwasher) in order for the dishwasher to complete full cycle. It is possible one of the switches is always on and this controls the wash system. Check the door latch operation and the location of the 2 switches in this diagram.
\015\012
\015\012Hope this will help you determine the problem and replace the parts. Please rate this solution if you found it usefuly.
Repair Help & Product Troubleshooting for Admiral 24 in. DDB1501AWW Free-Standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I Have 3 problems with my dishwasher, my dishes are always coming out with food and grit. I've tried numerous soaps and powders, the motor makes a very loud loud every time it's used. and the latch works but I can opent the door mid cycle it doesn't stop water sprays everywhere


Regarding the problem about dishes coming with food and grit - it is possible the wash water is getting contaminated with stuff that should normally be sucked out by the drain pump up in the dishwasher. This is linked to the accumulator and chopper p ... Admiral 24 in. DDB1501AWW Free-Standing Dishwasher

I have a Bosch Model SHE43F Dishwasher, only 1.5 years old. The door will not lock all the way like the latch is broke. But the dishwasher still works as normal without locking the door. The last time I used everything was ok. Looks like a programming problem, or latch mechanism broken.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. From what you have described the\015\012issue seems to be with latch mechanism as the Dishwasher is worki ... Bosch 18 in. SRV43M03 Built-in Dishwasher

I have a Frigidaire FDB2410LDC3 Dishwasher. It was working great until my 5 year old fell on the door and it does not spring back up now. I tried looking with a flashlight in the sides and the springs may be OK. What is most mystifying about this is something has gone wrong with the part your hand uses to close and open it. The latch is limp so I wonder if there was some other spring in there that broke in the incident. Now after some time of forcing it to shut (due to that pesky latch that


Prhandle and latch.obably sprung the hinges. The reason it dont want to work right is the door latch is not latching properly and therefore it wont start. I would start by replacing the hinges and springs and the ... Dishwashers

Kenmore elite dishwasher stopped in middle of cycle with water still inside. Checked breaker. Replace the hole control panel, door latch from a used kenmore elite. Work for half a cycle and quit with water still inside just like the first time.


Here's your solution (free PDF) - Kenmore Elite Dishwasher Manual ... Kenmore 24 in. 16352 / 16354 / 16359 Built-in Dishwasher

My dishwasher is not working properly, i have cleaned all the filters and spray arms, but still have food partials all over dishes. I did use a knife to hold down door latch so i could see what was happening when the dishwasher is working. Water does come out of the spray arms but they don't move and the dishwasher is empty, also now the latch won't catch since i used the knife.


Make sure the water temp is not too low. Make sure the pump is not clogged up with debris Check that hoses and spray arms are all clear. Remove spray arms and clean the holes in them. Make sure the shafts spins that the arms attach to. ... Bosch 24 in. SHE44C05UC Stainless Steel Built-in Dishwasher

Door latch I have this model and the door latch is not working....have hard time opening it now. How do you remove the tope part of the door that contains that latch so I can put in back in place????


The latch is fairly simple to replace. There are several screws around the inside of the door that hold the inside panel in place. You then will be able to slide the panel out of the way (it is attached by wires).You will then be able to ... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

Have a Bosch shy56a05uc dishwasher that suddenly stopped working to a point. I believe it is related to the door latch switch, because I don't feel the door securely latch shut when I close it, and I also don't get any cycle lights or times registered on the LED readout. If I depress the on switch, the drain pump will start even with the door open, and, depending on how long I leave the switch on, water will start to fill in the dishwasher, open or not.


Does your dishwasher electronic control or mechanical timer? if mechanical timer, I encounter a similar problem n change the mechanical timer. that problem solved.\015\012\015\012Prince P ... Dishwashers

I HAVE A WHIRLPOOL QUIET PARTNER 3 IT IS 38 MONTHS OLD IT IS USED 2-3 TIMES A WEEK BY WHEN I START THE WASHER, ONCE IT KICKS IN, IT DELIVERS THE LOUDEST SHRILL NOISE ONE CAN IMAGINE. IT IS GETTING LOUDER EVERY TIME I USE IT. IN FACT YOU CANNOT HEAR THE TV FOR THE LOUD ''SCHRILLY'' WHINE I AM OUT OF WORK AND HAVE NO MONEY FOR A REPAIRMAN I HAVE A 3 YR OLD HOME AND THIS REALLY BUMS ME OUT ANY IDEAS HOW I CAN SAVE MY WHIRLPOOL? THANKS IN ADVANCE MARTY


... Dishwashers

Door latch broke on my maytag dishwasher mdb6600awq. Worked one time, now does not turn on.


... Maytag 24 in. MDBH950AWS Built-in Dishwasher

After the cycle runs i open the door and all the soap appears to have just dumped out and is on the inside of the door. I have tried liquid and solid tablets of detergent and neither it working. It seems the soap door isn't opening at the correct time. The washer has only been used for a year! Any ideas of an easy fix? Thanks


Sound like you have to change your dispenser.chek out sear parts direct.com for parts,image,prices and part #s let me know if i was helpful. ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

When opening the door to my Kitchenaid Superba dishwasher, I heard a loud noise inside the machine. The door slammed open. Now, it opens, closes, and latches; however, the spring-assist that slows the opening no longer works, and the heavy door, when unlatched to open, swings freely and quickly down.


Well it sounds like you broke a spring,possably a cable you nooe to take off the bottom cover to find what broke. ... KitchenAid Dishwashers

The spring on the door broke (loud sound) and now the door is heavy and doesn't stay up unless we latch it each time. How do we find instructions for installing a new spring?


Its hard to find instructions but go to sears parts direct and order parts .you will see the location of the parts and a image that should put uyou in the right direction ... Frigidaire PLDB998A Built-in Dishwasher

For my Kudi01dl model dishwasher, the rinse light is on, but the unit will not respond to any buttons being pressed and won't turn on. When I press any buttons, two horizontal lines show in the front, but go off as soon as I let go of the button. Is there a ways to reset the unit? Everything was functioning fine the last time I used it. I use it about once a day. The problem started when I heard sounds coming from the unit, very loud motor sounds. The door was closed but I had not turned


... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher

My maytag quiet series fills with water and then starts for 5 seconds then stops. This happens 4 times and then the entire system just stops. To help troubleshoot I used a screw driver to trigger the closed door so that I could leave the door open when the cycle starts and the pumps seems to be working and water sprays all over the place. I also took apart the impellar blade to make sure there was nothing jammed and everything is clean. Maytag MDB7500AWW


... Maytag 24 in. MDB7600A Jetclean® II Built-in Dishwasher

Dishwasher leak I have a General Electric Potscrubber Mobile Maid dishwasher (model GSC720?) that hasn't been used in some time, but appears to still work OK. It has a leak from the left hand vent opening in the bottom of the door when operating. The seal around the door appears intact and doesn't leak. Can you suggest a probable cause, and remedy? Thanks, Bob.


With dishwasher empty and disconnected, find the screws around the area of the "vent",you may need to open it from the bottom. There will be a hose that has either ruptured or just needs the clamp tightened with a screw driver. I think that the hose ... Dishwashers

The dishwasher has three arms in it. The top and bottom arm do not rotate. The middle arm rotates fine. The arms will move when manually munipulated but do not spill while the dishwasher is on. There was a loud grinding the first time the dishwasher was used and it seemed to work fine but after about two months of use the arms will not rotate.


Sounds like maybe some rinsing salt was spilled when the salt reservoir was filled the first time (or broken glass, this always used to be an issue in catering) and got pumped through, lodging in the gap between the arm and it's mounting. this can ro ... Maytag Dishwasher

DU943PWKSO DISHWASHER STOPPED WORKING, ELECTRICAL CURRENT TO PANEL...THE LOCK LIGHT COMES ON WHEN THE DOOR IS CLOSED AND LATCHED, BUT THE WASHER WON'T START WHEN ANY OF THE BUTTONS ARE PUSHED...THE LOCKED LIGHT JUST BLINKS A FEW TIMES AND THEN STAYS SOLID AGAIN. ANYTHING I CAN TRY?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. This issue can be either due to a faulty door latch or\015\012door lock switch which is not engaging its ... Whirlpool DU943PWK - Multiple Color Built-in Dishwasher

Melted rubber gasket, black rubber residue inside dishwasher I had a problem with the latch not connecting and therefore could not turn on the dishwasher. After, two months with Sears repairmen, dishwasher still did not work. I noticed as I put my head into the dishwasher to check on a buildup of residue this black glue all over the inside. Repair man stated it was animal fat. After spending some time looking at the situation under the door and inside I determined it was the gasket. He o


That is because Sears highers nimrods. sorry for the honest answer but it is the truth. Just a tip any time you get a Sears tech in your home and the first thing they do is get on the phone with tech support it's a bad sign that they DO NOT KNOW WHAT ... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

MAYTAG MDB7600AWQ DIAGNOSTIC CHECK USING CONTROL BOARD AUTO AND MANUAL, ARE GIVING ME A HIGH CURRENT WASH MOTOR DIAGNOSIS.(NORMAL WASH FLASHING) THE BOARD ITSELF CHECKS OUT OK. ALL FUNCTIONS WORK AS THEY SHOULD.WASHER FILLS THEN ATTEMPTS TO RUN FOR (ABOUT 3 SECONDS) IT WILL DO THIS 3 TIMES THEN BOARD GOES BLANK. ALSO, THE WASHER WILL FILL WITH THE DOOR OPEN??? BUT WON'T ATTEMPT TO WASH. REPLACE WASH MOTOR?? THANKS lYNN


I would agree.. Here is a site for you to copy and paste in your address bar that I think will be helpful:http://home.howstuffworks.com/how-to-repair-a-washing-machine.htm/printable ... Maytag Dishwashers

Detergent dispenser will not stay shut so the soap power falls out before washing starts. Last time use I opened the door by mistake part way through the cycle. Could this have messed up the latch release mechanism? Thanks, slice10sheep


Opening the door did not affect the latch on the dispenser. The catch does wear out and can be replaced. This involves disassembling the door and a small jigsaw puzzle of springs and levers. If you are attempting I would advise taking pictures to ref ... Kenmore Dishwashers

Electrolux ESL63010 integrated dishwasher 10 months old- works for a few seconds, then stops and beeps continously. & the End indicator light flashes once. I turn it off, cancel programme, set it again, shut the door -it starts and goes on to complete the programme and washes the dishes perfectly. It has been doing this 'performance' for a week now -every time I use it- can you shed any light please


... Electrolux Dishwashers

I HAVE KENMORE DISHWASER MOD.#665.16034400 SERIAL#FR4603273 THE GREEN (CLEAN) LIGHT IS FLASHING AND UNIT WILL NOT RUN. CAN YOU HELP PLEASE? I have tried making sure door is shut and latched properly. I have tried cleaning contacts on heater coil. We bought unit new in Dec. 20004 but was not used untill this mo. It worked fine for about 3 wks. THANK YOU


... Kenmore Dishwashers

Nasty dishwasher there is nasty wet grunge at the bottom of the door, around the place the heating unit in the bottom of the dishwasher. half the time the dishes are clean in the bottom of the dishwasher. half the heating element is melted..for some reason...what do i do. the dishwasher still works, if we make sure the dishes are clean before they go in. using more for a sanitation thing than a dishwasher. can ya'll help me?


Sounds like your heating element is broken and you should replace it to prevent a possible fire hazard. \015\012You can replace the element easily for not alot of cash. You'll need to pick up a new one at an appliance parts store, just bring them the ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a Braun combimax 650--it is fairly new. It was working fine last time I used it, but this time, the dial that turns the machine on seems to be stuck. The little button for the pulse does work. I read the instructions, which said that this might happen when the machine overheats and to wait fifteen minutes, but it is definitely not an overheating problem and the last time I used it was weeks ago.I love this machine and now need to use it for quite a number of things--any help you can provi


... Braun K-650 CombiMax Foofs Processor FOR 110 VOLTS

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1643 seconds