Having problems with your AEG 23 in. Favorit 86070Vi Built-In Dishwasher ?

On an AEG Favorit 64570 VI we have an error 20. Manual indicates a drainage problem, however when we pour in water, it gets pumped out without a problem. No obstructing in the exhaust tube. Next we checked the pressure sensor, by taking it out and blowing into it. It clicked as pressure was applied to it, so the inner switch worked. Everything is clean, but still we get an error 20. What does seem strange is that the appliance does not take in water. Any suggestions are welcome.


Answers :

Repair Help & Product Troubleshooting for AEG 23 in. Favorit 86070Vi Built-In Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

On an AEG Favorit 64570 VI we have an error 20. Manual indicates a drainage problem, however when we pour in water, it gets pumped out without a problem. No obstructing in the exhaust tube. Next we checked the pressure sensor, by taking it out and blowing into it. It clicked as pressure was applied to it, so the inner switch worked. Everything is clean, but still we get an error 20. What does seem strange is that the appliance does not take in water. Any suggestions are welcome.


... AEG 23 in. Favorit 86070Vi Built-In Dishwasher

Hi there I have a Bosch SGV4313GB/17 Dishwasher the problem is there insuffient water pressure to feed the washer arm and they are not rotating Ihave cleaned the arms and circulation pump impeller with white vinegar ,I have also overriden the door switch and operated the dishwasher with arms removed and the circulation pump seem to be working but with insuffient pressure also the machine does not fill to the depth it did when it was fine! How does one tell if it is the impeller or the


Ours is a SHU3300UC/06 model, basic model which we bought in 1999 so have had 9 years of trouble free service.Recently\015\012we noticed that there was soap left in the soap dispenser after the\015\012machine had finished all the cycles. On fu ... Dishwashers

Westpoint Dishwasher I have a Westpoint Dishwasher. As soon as I press the start button the Machine goes on sound like it is working then all of a suddon it stops. Now it have 5 red lights burning and beeping when I switch it on. Do you know what the problem can be? Checke the water checked the filter everything is clean and working.


I put the mahcine on as normal but it does not go past the first cycle of the red flashing light? ... Dishwashers

Got a Diplomat ADP8322. Starts Cycle then starts bleeping 3 flashes which is a heating error. No hot water at all. Had a look and cleaned watr pressure switch still not working. Any ideas has the heating element gone.


Possibly heating element - only way to find out is to check continuity with a multimeter.there is also a thermal cutout in series with the heater which could also have gone ... Dishwashers

Model Karcher 320H 1.141-205 When first switched on the pressure builds up and then the machine keeps no switching on and off, opening the trigger on the lance and it works ok, close trigger and the pulsing starts again, if left like this it would probably burn the motor out. I have lubricated the brass/plastic piston the operates the on/off switch but problem still exists. I have also opened the pump chamber but cannot see any debris or problems with the rubber seals. Any help would be most app


... Karcher 1550PSI Pressure Washer

I have a kenmore DW model 16019. The clean Light stays on the light does not turn off. I have tried to disconnect and have taken the motort apart to make sure everything is clean. What Can I do to solve this problem? 1. Does the washer work at all? No it does not work 2. Does it display any codes or flashing lights other than the CLEAN LIGHT being lit? no other lights are on except for the green blinking light 3. Is the light solid or blinking? blinking Green light 4. Entire model # is necessary


Thanks for re-posting with all the info!!The model # is 665.16019403The cleaning light blinking is a fault code listed in the tech. service sheet, its usually a faulty heating circuit.The sheet can be found behind the ki ... Kenmore Dishwashers

Bosch she4am Unit starts briefly, then stops about a minute into the operation and lights the CLEAN led. I located the diagnostics code paper, ran the test a few times, and come up with the same code...the CLEAN led lit indicates a door switch problem. I removed the door switch, it's a magnetic hall effect transistor..seems to work but not sure it's showing proper voltages. It reads 8vdc or so across the switch with door open, and about 11.7vdc with door closed. Seems too narrow a range to me


... Dishwashers

I have a similar problem to another person. The drain on the dish drawer was blocked. The unit now shows an F1 error code ( flood?) and the pump runs continuously even after I've unblocked everything. I've tried switching it off for ages and drying everything out. When I switch it on again it shows the wash programme but then reverts to F1 and the pump motor runs continuously. Any ideas to cancel the F1 code?


The flood sensor on this unit is a PC board in the base, so you would need to remove the lower drawer and dry it out under there. If the base is dry and you still have the error, you can take a look at that sensor and clean any corrosion/minerals off ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Our Maytag MDB9100AWB is 5 years old. Have had repairman out several times. Problem is a light cloudy scum on everything. He has replaced several items, has had us clean parts and fixtures, etc and even had us switch detergents. Yuck, everything is cloudy and the sterling silverware has turned dark even after I scrubbed it all clean.


There are three typical causes of chronic cloudiness on glassware/dishes.\012\012The incoming water may be too hot. Make sure the water is at or below 140 degrees F.\012\012\012\012Test to see if cloud ... Maytag MDB9100A Dishwasher

My dishlex dishwasher is a model 560 silent range with eco save and has a printed circuit type switch arrangement it has man code of b8833ww or 88833ww the problem is that the pause start button activates but dose not latch in I suspect that the problem is with a latching relay behind the switch panel as i have had the front off and cleaned the contcts with contact cleaner! all of the buttons work including pause ! any advise would help as would a wiring diagram and or a operation or wor


Latching relay or door lock assembly need for you to check on that model number 560 silent range wont come out on dishlex's site should be a dx followed by some numbers try also to shut off the main power for 7 minutes to the unit to reset the contro ... Dishwashers

I have a slimline dishwasher from Ikea. The model is Whirlpool DWH C10 W manual. Everything worked fine up until the other day when I switched the machine on and it made a noise as if it was working but nothing happens. No water comes into the washer although inlet pip looks fine. I have poured water in and it is drained okay but the dishwasher is not cleaning dishes. After checking through numerous forum and reading about a flood prevention switch which can be sorted by tipping the d


Ok so slow down and lets look at the d/w problem and don't take the kitchen apart.. in the tank there is a float in the front corner. lift the float and listen for the click that would be the float sw . if no click th ... Dishwashers

My dishlex dishwasher is a model 560 silent range with eco save and has a printed circuit type switch arrangement it has man code of b8833ww or 88833ww the problem is that the pause start button activates but dose not latch in I suspect that the problem is with a latching relay behind the switch panel as i have had the front off and cleaned the contcts with contact cleaner! all of the buttons work including pause ! any advise would help as would a wiring diagram and or a operation or workshop ma


Hi.The switch on this machine's control module is electronic. I do not think you will find a relay. In normal conditions the button is not supposed to stay latched If the button is defective you may get the same problem when ... Dishwashers

My kew alto force pressure washer would normally cut out and start again in about 30 minutes. now it will not start at all. i have dismantled the pump from the housing and everything looks ok even the pressure switch is very clean. Could it be the on-off switch that is faulty. any help would be appreciated. fg


... Pressure Washers

Our craftsmen electric pressure washer stopped working while in use. We have power - red light on gfci and we tested the master switch - has power too. So what can be the problem? One post mentioned a jammed pump switch. What is that and where is it? We used it 2 weeks ago and it worked fine.


The pump switch they spoke of is an internal switch. It is activated by a valve so that when you let go of the trigger, the machine shuts off. This valve is stuck or the switch is bad. Usually the valve is the problem. I would go to Sears and get ... Pressure Washers

I was given a low hour, 10 year old, CH PW205002LE 6.5 HP gas vertical shaft 2000 PSI/2.5 GPM pressure washer with a Lavor pump. It did not work - no pressure. I found a broken o-ring on the brass unloader valve and replaced it with a ring as close in size as I could find as the part break down doesn't state size. Everything was very clean. I coated everything with silicine grease and reassembled, seating the brass piston? as deep as it would go. I had to press the trigger in order to get the mo


My personal experience is that 40% of all the sellers I dealt with on e*** exaggerated their products or worse. If you decide to go the e*** way be sure you put it on a good credit card so you can get your money back if it's a bust. Don't use your ba ... Campbell Hausfeld Pressure Washers

Code F2 I just replaced the door switch on an inoperable DD-602. My top drawer was working fine, but my bottom one has been offline for a while (door switch failed and I never got around to fixing it since I had the top). Well, my top finally failed too so I replaced both switches. Looks like everything is good on the top, but my bottom is erroring with an F2 code now. Kindof makes a thumping noise as it starts the cycle -- maybe 3-5 short thumps and then a 10 second delay, repeats. Any ideas? C


F2= \015\012The motor has not\015\012been sensed rotating\015\012\003 Foreign object has jammed the rotor\015\012\003 The rotor has failed\015\012\003 The hall sensor has failed\015\012\003 The electronic controller has ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a McCulloch FH160B power washer and it no longer builds up pressure. I haven't used this very much at all. I tore it apart and cleaned everything I could find. When i pull the trigger for the spray nozzle, I get line water pressure. When I release the trigger, the power washer sounds like it starts to build up pressure. When this was working correctly, the pump would shut off when the trigger was released. Any suggestions?


... McCulloch Pressure Washers

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Hi,This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder ... Dishwashers

I have a Whirlpool dishwasher model number DU1055XTPQ4 that is not cleaning the dishes. When the dishwasher is working, the bottem arm is turning and water comes out the holes. The middle arm has some water coming out, but does not turn. The top arm does nothing. It appears I have a pressure problem. I took out all the arms and cleaned them, along with the plastic tube that feeds them water. They had some build up on them but not much. I have the same result as before. I took off the


... Whirlpool Dishwashers

E6 I have been getting E6 error message over and over again. I have had the machine to pieces, cleaned out the pump and hoses, and still the same problem. Occasionally, the error message changes to E8 or E1, but no matter what, I can't get it to work. Any ideas? When I start the machine, select any program and close the door after a short while the machine does not complete the wash cycle and I get the following message either: E1 or E2 will appear in the control panel Any suggestions Dave M


I had this problem and fixed it tonight. When selecting a program water pumps into the machine, but with no drain i ended up with too much water and error code E6.\015\012\015\012I traced the fault to a broken wire between the electronic ... Smeg DWI614 Built-in Dishwasher

Dishwasher leaves baked on soap scum on al dishes and everything ....even on the dishwasher ...tried all kinds of soap and rinse aid...nothing works...cleaned entire washer out cleaned all filters ...nothing fixes the problem


I imagine you've already checked that you're using the correct amount\015\012of detergent for the wash programme, and that you're washing the\015\012correct quantity of dishes for the wash programme, though if not, try that first!Is the d ... Bosch Dishwashers

The top drawer of my fisher paykel dishwasher stops during the cycle and shows an icon of a tap with a line threw it (assume that means no or low water pressure). the bottom works fine so I assume water pressure is not the issue; is there a sensor that could be bad? Also, I did switch the controllers between drawers (good instructions on the fisherpaykelparts.net website) but the problem stayed with the drawer, ruling out the controller.


Did it fill with water? could be 1 of your water valves is faulty, or the little filter for the inlet water is blocked. please reply 4 more help. i"m sure i can fix this problem for you. good luck. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My tappan dishwasher is only 1 1/2 yr old and its not getting at least 1/2 of dishes clean. We have tried everything from changing to liquid soap, increasing water pressure at meter, not using while washing clothes. We used a dishwasher cleaner to remove calcium, and run hot water in sink before using. We know the wand, pump and drain are working. It is model TDB210RFB5 with 1.1A motor. Is the motor too small to clean dishes? I wish I could get my money back or exchange for an upgrade. Thanks!


... Electrolux Dishwashers

Proline Logic diswasher won't pump out water. Checked the following:- No blockage Pump works OK Pressure switch appears to work OK What other faults could cause this problem.


... Dishwashers

Hello, I am having problems witha kenwood dishwasher, it just isn't cleaning anything. It seems to be going through the cycles and sometimes the dishes particularly in the top rack are a bit cleaner but in general they are uncleaned. There are no error codes. I wondered if the arms for some reason weren't turning correctly as some of the dishes were clean but this is inconsistent. I have tried changing detergents, adding more salt and rinse aid but it still isn't working, can you help?


... Kenwood Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1814 seconds