Having problems with your AEG 24 in. Favorit 40630 Free-Standing Dishwasher ?

Problem with AEG 24in Favorit 40630 Free-Standing Dishwasher When I'm turn on the machine the top and middle signal light are flashing and the pump working for some time and stop. I know this device detects water leaks and is a polystireene float / micro switch that puts the machine in pump out mode. But there are no water under the float! Alex


Answers :

Repair Help & Product Troubleshooting for AEG 24 in. Favorit 40630 Free-Standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Problem with AEG 24in Favorit 40630 Free-Standing Dishwasher When I'm turn on the machine the top and middle signal light are flashing and the pump working for some time and stop. I know this device detects water leaks and is a polystireene float / micro switch that puts the machine in pump out mode. But there are no water under the float! Alex


... AEG 24 in. Favorit 40630 Free-Standing Dishwasher

Hi, I have a Hoover silent whisper HD98E dishwasher and it's leaking. I know where the leak comes from. Once the machine is on, it pumps the water through the salt container and through these 3 pronged blue container (located on the side). One of these prongs leaks. I believe it is the washer. Can you tell me where I can buy a new washer? Are they specific to Hoover dishwashers or can I get them from Plumbcenter? A quick answer would be very much appreciated. Thanks.


... Hoover 24 in. HD98E Built-in Dishwasher

KUDK01ILBS5), SN: FR2702809. Have used this machine 6 years and just recently experienced noise that I eventually traced down to a bad recirculation pump bearing that failed due to a small leak in the shaft seal. Installed a new pump on Friday, 4/21/10 and that particular noise is now quieted. While the bearing noise was gone, there remains a pumped water noise that is quieted by manually adding about 1/2 gallon of water within the machine. So I now believe the water level is low, possib


The water level in the machine should be slightly under the heat element. The float you refer to is only for overfill and should not be activated if the machine is filling properly (the water level should be lower than the float switch activation poi ... Dishwashers

Some guys at the church was using this haracher 4000 psi, I was call and was told the machine stop working and would not crank up.I use a next machine to finish the charity jobs on saturday. Sunday the machine starts up but when I connect the garden hose and turn on the water it did not comes out, where the VALVE HOSE THAT GOES TO THE WAND ABOVE THE UPLOADER, I open every bolt and water comes out except the wand valve, pump was plush out and sprayed out, so we know that water enter the pump


Where the hoses attach to in the pump is a valve along with another valve inside of it. Remove both valves and clean and relube with Vaseline or equivalent. The inner valve will be the toughest one to remove and that its why it does not work if stuc ... Karcher Pressure Washers

Westinghouse SB915WJ is leaking cold water underneath machine. Working fine, just leaking water. Have changed door seal but it is still leaking. Also tried leveling it but this has not helped. Would like to access underneath and see if clamps are on tight but don't know how to access this part of machine.


... Westinghouse Dishwashers

I have a Bosch Exxcel dishwasher which runs the drain pump constantly even with the door open and despite there being now water in the machine at the cycle wont start. I have checked the warer amtrix and the ffed hose to the sump for blockages. The float switch operates OK but when the water drains down the float drops and the water is pumped in, then the float rises and water leaks out and the drain pump kicks in again and no more ater will come in unless you push the float down. Inside the bas


I am not sure about this model but most models run a drain cycle for a set period at the start of a wash cycle and then move on to normal filling and cycle of machine provided the various switches are at the low level it will carry on to its set cycl ... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

E1 fault code Dishwasher runs for about 5 minutes. Water fills up at bottom of unit and then machine seems to pause then fault code E1 appears then water is pumped out from bottom of machine. There are no leaking pipes and drain is installed correctly. I installed a new wash pump and fault still appears.


Hi,\015\012I think both the heater and thermostat / trip switches need to be checked.\015\012If water is going in and out ok, then it seems to be waiting to heat the water. It sees a fault - so just clears out.\015\012Heating elemen ... Dishwashers

My Bosch Classixx (about 10 years old) dishwasher won't fill The problem has only started since I pulled it out and cleaned! The programme sounds are as normal but no water enters the machine. I detected a small leak on the inlet pipe and tightened that. The machine drains when I add water manually though it has made a lot of gurgling noises for some time now when draining. When tipped on its side water comes out of the bottom of the machine (not entirely clear but not dirty either). When upri


... Bosch SHU9915UC Dishwasher

Over the past two years, the machine has occasionally stopped in mid cycle, while the pump continues to run, but the cycle stops advancing. Each time there has been water in the plastic pan under the pump, valves, and other mechanisms. The float switch has been tripped, stopping the cycle. Occasionally. but not always, the pump inlet has been partially obstructed by food waste. After bailing out the pan, the machine will run normally for weeks or months. There is no indication of a leak into th


Please post the exact make & model # so we can be more exact.\015\012THanks!! ... Dishwashers

Dishwasher leaking. I was supplied a flat seal ring of about 100mm dia., 10mm wide & 1 mm thick for the machine when I bought the house. Water on the floor tells me something underneath is leaking for the first time. The machine is about 10 yr old and in very good order .This seal could be the problem so before I go getting service personel in I'd like to know if replacing this and the door seal are jobs a careful handyman can do ?


I would say you could do it with out a tech.More then likely you can find information on the web on how to do it step by step or hey use this site more then likely one of us has had the same problem. ... Dishwashers

My ariston lsv 66 dishwasher will not start washing cycle. It makes the pumping noise as it normally does at the start of the cycle and some water enters the bottom of the machine but then it stops. I have checked to make sure that there are no leaks so the problem is with the filling up of the machine. I live in a hard water area and haven't used anything to help reduce the limescale so expect this to be playing a part. I have tried all the washing cycles but the same thing happens. Any advic


HERE I AM I LIKE THIS JOBE\015\012 PLEASE CHECK THE WATER INLET FILTER I FEEL FROM YOUR DESCRIBE IS IT\015\012 YOU NEED TO CLEAN IT BY ASMALL BRUSH >\015\012 THANKS ... Dishwashers

Leaking input to the top of the dishwasher. Pollypro pipe comes up the back and into the top centre of the machine.... This is squirting out water when on wash cycle. Have undone large plastic nut on iside.. that has rubber washer on it... but the input pipe does not seem to have a washer between this and the steel body of the machine... this seems to be causing the water to squirt out... please let me know whether the washer has disintergrated or whether I need to use some bedding compound t


\015\012By reading Your problem most probably due to disintegration of washer only. Try with new Washer \015\012\015\0121. First try to adhere some wax or gumming material where washer is distingrated...if it solves u r probl ... Dishwashers

I just finished a service call for my 5312UC/UC12. The tecnician says he saw water leaking under neath the machine but hoses were secure and no visible crack to the motor housing, The machines pump works but very little water is actually put into the tub, hence no dishwashing. This technician says that this is a repair that most technicians avoid because it takes a long time and costs alot and violated some sort of warranty. He recommend replacement after only 7 years!


This leekage may come from thermostads water isolation ring, just under rezistance leads. There must be a ceramic holder to fix it to rezistance. İf it is broken, thermostad may go down, or rezistance leads isolation (lastic washer) may leak wat ... Bosch 24 in. SHU66C05 Stainless Steel Built-in Dishwasher

Hello, I have a problem with our Miele G646SC Plus dishwasher. It starts its cycle OK, draining out any residual water, taking in fresh water and doing the initial rinse. After about 5 minutes it then stops with the "inlet/drain" red light flashing. The detergent is still in the holder and the water is still cold. The filter at the bottom of the compartment is clean, the drain pump spins freely. I've also checked for any leaks in the bottom of the machine that would trip the styrofoam/microsw


Hi\015\012\015\012 \015\012\015\012The light flashing means an issue while draining. You would need to check for air\015\012gap on the dishwasher, it may be clogged. It prevents dishwasher\015\012from drain ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

Aeg favourite 50500 machine will not complete cycle but pump still runs . i have taken side panel off and dried water out of bottom of machine how do i get to leak???????? Ihave tried tipping machine through 45% but this is only a temporary fix.


... AEG Favorit 50500 Built-in Dishwasher

When I power the Karcher 520M water pours from the handgun - there is now leak until pressure is applied. the pump does not cut out but I don't know if this is a problem with too much pressure causing the leak or too little pressure because of the leak. there does not seem to be a way to dismantle the handgun - is this correct Bill


Not too much pressure, a bad gun.Unfortunately you will have to replace the gun. About $65.00 Canadian ... Karcher 2500 PSI Pressure Washer

I bought a secondhand Miele 2830 LaPerla dishwasher. I hooked it up today. As soon as I pressed the start button, i heard the pump anf it gave me an F68 error and water leaked out of the bottom in such a way that I could not see where it was coming from. I know f68 means the circulation pump is running when it isn't supposed to. Since I heard the pump, I imagine that is working. So any advice on how to fix this?


The hoses may not be connected properly or are cracked. This is causing leakage inside dishwasher and the flood switch to operate. The dishwasher starts the pump to empty the dishwasher and avoid damage of water flooding the electric parts.Yo ... Dishwashers

Trips power when it is turned on at the on/off switch. There is a little bit of water on the baseplate so obviously a leak but i can't see it. Anyone know of common leak points on these machines ? Thanks Steve


Go to the Hotpoint website - there is a trouble shooting section. Failing that find the customer service number on the website and ask if there is anything you can do to solve the problem yourself before paying for a service call. I would alway opt ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

BOSCH SGS 5602 Dishwasher It got stuck on 45 mins and the pump was working overtime but there was no water in the machine. Looked it up on the internet and found similar problems caused by the machine getting the message that it was flooding. Emptied the overflow and everything was fine until it reached the same stage in the programme. I assume there is a leak somwhere but how do I find it


... Bosch 24 in. SGS56A72 Built-in Dishwasher

Have got a bauknecht dishwasher model no gcx 5521. had the same problem last year. water is not going into the machine it looks like the water stop device activated. I think its something to do with a flowmeter. just wanting to know how to reset it without having to call an engineer


Have got a bauknecht gsx4756 which when started beeps continually and start light flashes. it automaticaly then flashes the rinse button as well. I have reset holding down start and mode selection button next to the start button the fault keeps recur ... Bauknecht Dishwashers

Hi there,i have a brand new but 3 year old,diplomat 8332,just fitted it,it does the pre was ok,pumps out the water,goes to next stage,you can hear water entering the machine,shortly after it has started the main wash,it starts to cut out intermittantly,then F2 code appears,and a bleep.i have taken the lower panel off and checked for leaks and to see if the valve was free,all ok,also relay click in front panel,safety cut out ? any ideas please.


... Dishwashers

SHX46B I have a 4 year old Dishwasher that filled up with clean water on it's own and leaked on the floor. There appears to ba a float switch switch on the very bottom of the unit that runs the pump if this happens. It won't stop until I remove the water caught in the plastic base on the very bottom of the unit. Drain is clear and this machine has worked fine until now. I'm thinking it may be a bad or leaky fill valve but how can I check?


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

My vulcan dishlex e500 is not pumping out water. Water is going in but then seems to overflow and leak out of machine. Cheers for any help.


Firstly correct model would help,500E is only the series; but from what you describe a number of faults could prevail: "1" the breather on the air dome could be blocked. "2" faulty pressure switch."3" faulty restrictor in p/switch tube:All these pote ... Dishwashers

I have an Ariston LS245 dishwasher, have just had the pump replaced, as it had shorted out, due to water in the bottom tray where the water detection float is, also a new drain hose fitted. Have just run a wash and after running a while, presumably to the end of the rinse, wash and dry cycle, then one of the cycle phase lights, the one for 'soak' blinks constantly. I switched the machine off and had a look to see if a wash had been done, the dishes look clean. In the book it says that if one


... Ariston Technologies Dishwashers

Good mroning after starting any program first the pump will run followed by water intake. After a while the machine stops and the light intake/drain starts blinking. Most of the time water will stay in the machine. After pressing the on/off bottom first switching the machine on again and starting a new program the machine pump start running emptying the water but than stops after a short water intake again. I opened the water stop but it seems to be ok. The filter inside the machine is cle


Good morning don't get shocked because ullu ki to abhi subah hi hui he ... Miele 24 in. G892SCU Plus Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1801 seconds