Having problems with your AEG 24 in. Favorit 40850 Free-standing Dishwasher ?

AEG Favorite Compact 525 Dishwasher. The pump runs continuously even when the on/off button is pressed. any ideas


Answers :

This is caused by the Anti-Flood device at the base of the machiene being activated. This device detects water leaks and is a polystireene float / micro switch that puts the machiene in pump out mode only. You need to determine where the leak comes from (pipe or perforated hose pin hole or pipe clamp etc.) If you tilt the washer and some water comes out from the bottom it is a clear indication that there is a small leak.
Repair Help & Product Troubleshooting for AEG 24 in. Favorit 40850 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

AEG Favorite Compact 525. The pump runs continuously even when the on/off button is pressed. Tho only way to stop it is to turn the power off at the socket/plug. any ideas


This seems like the anti flood system (polystireen float / micro switch) at the base of the washer is triggered,\\. This puts the washer in pump out mode and stops inlet of water via the inlet solinoid. Dry the water on the base and then check for an ... AEG 24 in. Favorit 40850 Free-standing Dishwasher

AEG Favorite Compact 525 Dishwasher. The pump runs continuously even when the on/off button is pressed. any ideas


This is caused by the Anti-Flood device at the base of the machiene being activated. This device detects water leaks and is a polystireene float / micro switch that puts the machiene in pump out mode only. You need to determine where the leak comes f ... AEG 24 in. Favorit 40850 Free-standing Dishwasher

I have an avanti dw 18 dishwasher . the problem i am having is the when i turn the on button on the motor goes on however no water fills up. The motor is only humming. But; when i press down the float from inside the machine the water fills up and the machine starts to work. after the water drains again the motor continues to run and hum and the dial does not move. when i manually move the dial nothing seems to change . the motor continues to only hum. Even when the dial is in the stop position


... Avanti Dishwashers

I have a GE monogram zbd5900 that continues to drain, won't shut off. The drain pump just runs. None of the lights on the control panel will come on, tried pressing and holding buttons to clear, nothing. Turned off and on circuit breaker (even left it off overnight) and did not change. Drain is not blocked, pulled the unit out and put water in the bottom and it pumped the water out just fine. any thoughts?


See if you can access the tech sheet, should be on the right side of the underside of the unit after you remove the toe panel, or perhaps in the console. Almost sounds like a stuck key pad but the tech sheet might shed more information on this malf ... Dishwashers

Hi My F&P dishdrawer flooded. Dried it all out etc, the top drawer doesn't complete the cycle and it beeps continually even when it's not running. I am wondering if I can reset the drawer using the front buttons to get it back to factory default. Bottom drawer works fine. There is no error code on the screen only the lock icon which won't go away. Any ideas?


Not sure if you tried turning the power off at the main switch. Lock icon can gone away if you press the necessary keys as shown in the user guide. Also the sequence of keys to press for getting factory defaults of different options is also in the us ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Hi I have a problem with my Bosch SHU43CO6UC/22 dishwasher. using "power scrub plus" and "regular" cycles it will continue to fill and overflow the door, after the cycle has run even when the power button is off. I am using the quick wash cycle at the moment .After the cycle has run i open and check if the water has drained or not,If it has it does not continue to fill and flood.If there is water in the bottom after the cycle has finished it will keep rising untill I push the rinse hold button


The bosch dishwashers use a fill valve that is attatched to the inlet hose. yours is stuck in the open position. this usually happens when you have hard water, as the minerals build up on the sealing surface of the water valve. there is no easy ... Dishwashers

My dishwasher will not start. If you unplug it and plug it back in it says 1H, no matter what button you press it then says 2H and if you press another button it will say 3H until it runs through to 9H then will display --. It will continue to do this until you leave it alone and walk away. Then after a few moments it will clear itself out and the 'Normal' light under cycles will continue to blink. The dishwasher is 3 maybe 4 years old. Please help, I have a 3 year old and an 18 month o


Hi,There could be Few Possibilities.Let's try to Reset. 1h, 2H -----9H usually shows delay X hours Display where X would be 1,2...9.Turn the Power OFF for few minutes, say 5 Minutes and then Turn it ON. ... Dishwashers

I just bought this house with this dishwasher built in. I have pushed the door shut, pressed the heat dry button to lock the door and pressed the start button. Nothing happens. Now I can't even get the lights on front to turn off. The lock button flashes as though the door is open, but its not as far as I can tell. I have to press the latch in to open the door. I'd like to use it... any ideas. Its a Kenmore Elite model # 665 17052 402. Thank You


... Kenmore 24 in. 17052 / 17054 / 17059 Built-in Dishwasher

Hi experts, My Indesit IDL530 dishwasher never seems to run on any of the 5 programmes. On pressing the power button, the red light comes on and on pressing the start/reset button, the light signalling washing comes on and not the one showing water intake. But even then nothing progresses and just a buzz with that wasing indicator on shows for a second and goe off. But today only the buzzer sounds when pressing down the start/reset button and no indicator comes on atll. Will be great if you coul


... Indesit Dishwashers

I have a Kenmore Ultra wash 665 15895 dishwasher. It will not run any cycles. Symptoms: When I first close the door, the "Quick Rinse" light is on and the number 18 is displayed. When I push any button, the "Quick Rinse" light flashes continuously. If I touch any other button, both the "Quick Rinse" and "Pots and Pans" lights flash continuously. No matter what buttons I press, the behavior is the same. I've tried turning the power off and on, same behavior. The only button that doe


\015\012HiThis may be an issue with heater circuit, door switch or wash pump. Press and hold the heated dry/air dry button for 15 seconds....After, 5 minutes check if you are still getting the same error. If yes, ... Kenmore 15899 Built-in Dishwasher

I have an older GE dishwasher, model GSD1200T02. I recently put in the wrong soap, so I had to press the clear/reset button. When I did this, the dishwasher ignored me and seemed to continue through the cycles anyway. When it got half way between "drying" and "off", it stopped, and has been that way for several days now. It will not respond to any button pushes at all now. I cannot even reset it because it does not respond at all when I press the clear/reset button. I have had a load of di


This is only a long shot, try turning the breaker off and on again, may be ???\015\012 Jacques. ... Dishwashers

I have a similar problem to another person. The drain on the dish drawer was blocked. The unit now shows an F1 error code ( flood?) and the pump runs continuously even after I've unblocked everything. I've tried switching it off for ages and drying everything out. When I switch it on again it shows the wash programme but then reverts to F1 and the pump motor runs continuously. Any ideas to cancel the F1 code?


The flood sensor on this unit is a PC board in the base, so you would need to remove the lower drawer and dry it out under there. If the base is dry and you still have the error, you can take a look at that sensor and clean any corrosion/minerals off ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Model # SHU 8806UC/14 When start button is pressed, with door open, it begins to cycle and even if we close the door it just runs and runs but never dispenses soap from the dispenser or even fills with water. Any thoughts?


... Bosch Dishwashers

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers

Hi, I have a Kitchenaid KUDI01TJWH0 dishwasher that failed. Any of the front control buttons like Heavy-Normal-RinseOnly or even the HiTemp-EnergySaver .... when you press any of these, the corresponding light for it will blink three times and go off. Normal operation that light for that button will come on and stay on. but none of the lights stay on. If you press start, the 'water heating' light will come on and you will hear the pump run for about 10-15 senconds, and then everything goes off


Hi Your Problem is Probably The Control Panel. Not The Electronic Control. The Plastic Piece Across the Top of the D/W, Which Tells the Control What to do But You Must Realize These Parts Can Be Very Expensive. John H. Been in this Business 35 Yrs ... KitchenAid Dishwashers

Electronic controls the dishwasher will not turn on. press and hold the heated dry button for 5 seconds and the machine came back to normal. now even that is not getting the machine back to normal. the normal button and start buttons flash but machine does not function. i have the front electronic panel off and do have a volt meter to test if you could run me thru the proper procedures.


First thing to check is the door latch switches, and hte strike plate(metal tab protruding from the top of tub assy in which the door closes into, if bent up to high the door will not be recognizedas being closed. you can use a small screw driver nad ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Have a Karcher kb4040 that continues to run constantly even when the trigger isnt pressed. Also water flows out of the detergant hose when im not pressing the trigger. Pressure seems down slighlty, not much. This happened after i ran water out of trigger gun with no lance attached, machine switched on. Seems to leak from trigger handle aswell. Many thanks in advance


This is two things. One is the back flow check valve to the soap line is leaking. The other is the pressure switch on the output side of the pump. ... Pressure Washers

My Bosch integrated dishwasher(model SGV56A03 GB/12) runs through the cycle but doesn't stop at the end of the cycle. It continues to heat water and it sounds like the motor is running even though the time indicator shows 0 minutes. I have to manually switch it off. Any ideas before I call out an engineer. I have checked all the filters etc included in the troubleshooter info anf there are no blockages.


... Bosch Dishwashers

I have a Hotpoint FDW80 Dishwasher. The drain pump runs continuously, even though there is no water inside, I poured water in with a kettle and it does drain correctly. After a short while fault code AL01 appears. I have removed the base tray to check the "anti-flood" swithch and that is OK, even with the switch disconnected, I still get AL01. Any ideas?


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

The dishwasher pump sounds like it is trying to drain, even when the stop button is pressed and the door is opened. The only thing that stops it is turning the power off at the power point. However, when the power is turned on the pump continues. The wash cycle icon flashes, but the usual cycle indicator is not lit at all. The dishwasher will not commence a new cycle.


... Asko D3122XLW / D3122XLB Dishwasher

Dishwasher stop running with about a minute left to go, water still in the bottom. Following lights are blinking; high temp wash, sanitize, and no heat dry. I have check that the garbage disposal is clear, even ran it for a while. The over flow valve does move up and down. Pressing the buttons mentioned above does nothing.


I am assuming this problem has been fixed. If not then please post a comment to confirm which bit is still not resolved. ... Frigidaire Dishwashers

My Kenmore 15882 dishwasher continues to fill with water. We keep pressing the cancel button to drain the water. Any ideas?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for\015\012using FixYa. If the dishwasher is overfilling it’s ... Kenmore Dishwashers

AEG Favorit 6040 Dishwasher has continuous tone (from Pump?) even when switched off at the power button. It cannot be set to any programme.It overflowed some froth when put on a recent cleaning 'phantom wash'. Please help, Chris.


This sounds like the anti flood system has triggered. This does put the washer on a pump out mode and the outlet pump runs all the time. The trigger device is a polystireene slab in plastic bracket with miro switch at the bottom of the washer. Dry th ... AEG 23 in. Favorit 50750Vi Built-in Dishwasher

I started my dishwasher this morning. It started to fill with water, then stopped. I can hear a very slight hum sound as if the motor is running. The start/reset light flashes but does not reset upon pressing the button. Any ideas for a self-help resolution?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. This issue can be either due to a faulty door latch or\015\012door lock switch which is not engaging its ... GE Nautilus 24" Built-in Dishwasher

Dishwasher not getting enough water in either drawer, although top drawer gets more. Dishwasher keeps beeping during cycle and reads not enough water and then stops running until you press the start button. Need Help, any ideas?


This sounds like a hard water deposit problem.Check your water inlet valve for a screen and see if its clogged. Also it may just be a water valve/solenoid problem. As in, it's too crusted up to float up and down.Some models have a water f ... Fisher and Paykel DD605FD Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1016 seconds