Having problems with your AEG 24 in. Favorit 40850 Free-standing Dishwasher ?

No hot water in dishwasher or heat to dry dishes


Answers :

I had this problem too, and was able to fix it. There is a generic \015\012problem with AEG dishwashers of this type, caused by the bad solder \015\012joint of a relay on a circuit board. Solution:
\015\0121. Disconnect mains power then open washer and remove the 8 or 10 screws\015\012 that hold the inox plate onto the door.
\015\012
\015\0122. Gently peel away the inox plate and you'll have access to a white \015\012plastic box at the top of the door where the pushbuttons are located.
\015\012
\015\0123. Undo the 4 plastic clips on the sides of the white plastic box and \015\012you'll have access to an electronic circuit board. Note the order of the\015\012 6 or 7 wire connectors along the edge of the circuit board and then \015\012unplug them. The circuit board is now only held by a flat plexi \015\012connector. Leave it attached.
\015\012
\015\0124. Gently turn the circuit board over and look at the solder joints. You\015\012 should see one or more dodgy solder joints. Use a soldering iron and \015\012some extra solder to redo the joints.
\015\012
\015\0125. Put it all back together in reverse order to above.
\015\012
\015\012This is a known problem (that no one knows about).
\015\012
\015\012David.
Repair Help & Product Troubleshooting for AEG 24 in. Favorit 40850 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Even though I turned up the thermostat on my hot water heater, the water in the dishwasher does not seem to be hot enough. Mold is growing in the food grinder and even though I choose the heat dry option, the dishes are never dry. Yet, when I touched the element, I got burned. The dishes are not getting clean because it doesn't seem to be hot enough to cut the grease.


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Yes I have a whirlpool DU1345XTVB1 dishwasher. Just got in July. After each wash cycle the dishes are not dry. I have been using Finish gelpacs w/jetdry & also have a off brand drying agent in reservior to help dry dishes. The water temperature is set pretty hot & washer is draining good. I have tried checking wash cycle a few minutes into 1st cycle to see if water is in filling & heating. Didn't know if maybe heating element going out or thermostat not working? Thank you for your time.


<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-language: EN" lang="EN">Hi,<br />Check your heating element.. </span><br />\015\012<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-lang ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

Leaking from under dishwasher. Has run great since 1996. Under counter model in manufactured home. Chnaged to drop in pellet dishwasher detergent and it ran great. There is no water inside the dishwasher circular drain. We never use the heating coil to dry the dishes. We have turned off the water supply line under the sink to the dishwasher. Cool clear water is running out from under the bottom right corner. The hot water heater is right next to it and everything is dry and warm under it which i


Hi,Depending on the model you have this could be a couple of things. The most likely suspect is the water inlet valve. What I would recommend to do is take the bottom toe panel off, typically there are either 2 or 4 screws holding this pa ... Dishwashers

I have a 2 year old Electrolux ESL 63010 dishwasher, and it worked perfect until a few days ago, when it did not wash cleanly and the dishes came out cold. I read a few forums and it seemed to indicate the heating element. So I ordered one a fitted it, but still the water is not getting hot, or drying the dishes after the complete cycle. I have done a visual check of the PCB board, which looks clean and good. No error sounds, and it completes all programs, but with cold water and no drying. W


... Electrolux Dishwashers

I have had a repairman come out and look at this and he says all the diagnostic test say everything is okay. My problem: my dishes come out dripping wet...like it hasnt dried anything. Sometimes dishes are still dirty. I don't think there is any heat getting to anything. I run the water in the sink beforehand to try to get the water hot. I used this dishwasher for 1-1/2 years with no problems and now I have this problem. What is going on?


I am having the same problem but do not see any posted solutions. Have you solved this problem? ... LG LDS4821ST Stainless Steel 24 in. Built-in Dishwasher

All of a sudden the dishwasher water is not hot (usually the water is very hot when wash the dishes ).... even when I put the hot water sink tap running out hot water... then start the dishwasher. the rinse cycle only warm water ... usually the water is steaming hot and drying cycle the dishes are too hot to touch ....


Check the heater. Heater control circuit. ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I have a dishwasher model 66516979200 it doesnt dry the dishes i saw the heat sensing light on an opened it and felt the heating element and it was not hot at all ive checked the water temp at the sink and it is at 120 could the heating element be the problen or something else


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

The washing, heated dry, and normal wash light just flash. I have unplugged and plugged it back in several time, i tried restting it by holding down the Rinse only button for 15 seconds. I pressed the high temp ater, heated dry, high temp water, heated dry buttons to try to reset. I also ran the hot water line that feeds the dishwasher until the water was hot. Nothing has helped. The machine is18 months old and therefor no longer under warranty.


Please provide the make and model number of the dishwasher.\015\012do you hear pumps running? what was the last cycle it was at when the flashing started. was there water left at the base of the dishwasher from the cycle that stopped? ... Dishwashers

I own a GE Profile Built-in Dishwasher Model number is PDW7880G00SS, Serial number is FF7872828.  We have recently been having major cleaning issues with it, especially the top shelf i.e. the glasses.  There is always dried up debris on them.  We always run the water hot and run it on "added heat" cycle.  I was wondering if there is a filter, or an area in the dishwasher that needs to be cleaned out?  Even if I put perfectly clean dishes in there, they will come out dirty, which leads me to thin


... GE 24 in. Profile PDW7880G Built-in Dishwasher

Dishwasher I have a whirlpool dishwasher that does not appear to be getting hot water. The washer water is cold initially and only seems to get warm once the heater in the base of the machine heats it. The hot water supply line does not get hot so I presume no water is being supplied. Is the water supposed to be hot at the start. If yes could this be caused be a faulty inlet valve and if so how can I check. The dishes are dirty especially on the top rack. Thanks for your help. David


Gendos is on track with his question. I have the same dishwasher and it doesn't get enough hot water to clean the dishes and runs for hours because the heating element wasn't designed to heat water, just maintain it. The only solution we have found ... Whirlpool GU2400XTP Built-in Dishwasher

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

Our Whirlpool KUDP01ILBS2 dishwasher isn't working like it used to. Dishes seem to be getting partially clean, they aren't getting dry at all and it seems they may be being rinsed/washed with dirty water. There is plenty of water in the machine when I interupt the cleaning cycle. I always run the hot water in the sink before I start the dishwasher so the first water into the dishwasher is as hot as possible. Also the sani-rinse light is flashing when the cycle "completes".


Heat that is retained in the dishes is largely responsible for drying\015\012in this dishwasher. Since plastics do not retain heat very well, they\015\012will not dry as well as glasses, ceramics or metal dishes. Rinse aid\015\012must be used so that ... Dishwashers

My dishwasher zsf6152 isn't producing any hot water and heat to dry the dishes after the wash. Is it worth repairing?


... Zanussi 24 in. ZSF6150 Free-standing Dishwasher

No hot water in dishwasher or heat to dry dishes


I had this problem too, and was able to fix it. There is a generic \015\012problem with AEG dishwashers of this type, caused by the bad solder \015\012joint of a relay on a circuit board. Solution:\015\0121. Disconnect mains power then open was ... AEG 24 in. Favorit 40850 Free-standing Dishwasher

The Superba dishwasher is not longer heating the water hot enough that the dishes will dry themselves.


Your dishwasher has a heating element that heats the water. If you will callor email us with the model number, we'll send the right element out fo roy u to insyall. They are very easy to replace. Hope this helps! ... Dishwashers

Bosch Dishwasher I currently own a Bosch dishwasher. One of the selling points, if I'm remembering right, of the dishwasher was it was supposed to super heat the hot water that is coming in from the tap. I have 3 problems. We have to rinse the dishes by hand before putting them in the dishwasher, Otherwise they won't come out clean. The dishwasher will run for four hours sometimes longer. It doesn't seem like it is heating the water any hotter than what comes out of the tap.


Your control board is bad. ... Bosch 24 in. SHU43 Built-in Dishwasher

I also have a dishwasher (AEG Favorit), and it does not heat the water anymore. It worked fine for last 3 years, and all sudden, it only washes dishes with cold water. Could you please help to solve this problem? The hot water line is fine and I do have the hot water to the sink next to the dishwasher. Thank you in advance for your help.


... AEG 23 in. Favorit 44070IW Built-in Dishwasher

My kitchenaid dishwasher will not complete a washing cycle. the water heating seems to be staying on all the time. could my heating element be shot. the water seems hot when i open the dish washer during the cycle but it is connected to the hot water supply line. thanks


... KitchenAid Dishwashers

Our dishes smell like vomit after they have dried. We run them through the dishwasher, they seem to smell okay. Then when Dry, the smell returns. We have tried vinegar and tang rinses to no avail. We have turned up the heat of our water to scalding, that hasn't helped. We have disconnected drain hose and there is no smell there. What can we do to get rid of this awful smell? There is no food in any filters, heating element is clean except for some hard water stains. We have a whirlpool 575-0 qu


... Whirlpool Dishwashers

My technica dishwasher water is not getting hot anymore. I am now washing in cold water and of course the dishes do not dry. The machine is 6 years old.


... Dishwashers

My dishwasher emits a dead animal smell immediately after filling. I have a 20-year-old KitchenAid KUDS220T3 dishwasher. The racks are a little corroded, but it still cleans dishes just fine. About two months ago, it started smelling like a dead animal immediately after the dishwasher fills with hot water, during the time the water is being heated, but before agitation begins. The smell appears to be coming from around the door. If I open the door, everything inside the dishwasher smells fine.


This vent that you are describing is to allow air to flow in for the heat/dry cycle. Some times little creatures want to "mark" their territory by "spraying". Spray some type of cleaner like ammonia into it and **** it out with vacuum a few times. Mo ... KitchenAid Dishwashers

My GE Potscrubber 2230 is not heating the water in the dishwasher. The water at the sink is hot but when I ope the dishwasher, the water is closed. Sooo, it's not cleaning the dishes. Is there something I can do or do I need to call a repair man?


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The Heating Element not W ... Dishwashers

Kitchenaid dishwasher dishwasher is 5 yrs old. Recently the dishes don;t look dry and sometimes aren't clean even when you use the scrub feature. Hot water works at sink but we don't see steam coming out of dishwasher and the door doesn't feel hot to touch as it used to. Help please.


May have a heating problem.need to check for power to element,if no could be board fault,broken wire in door,if power is getting to element the the element could be faulty.hope this helps. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Detergent cup Help!! I put jet dry dishwasher CLEANER in my jet dry dispenser. The bottle says "don't" and "make sure no dishes are in dishwasher". How can I clean it out? I've tried running it a million times, and pouring really hot water into it and still I get a murky backwash. I know it's all poisonous, but this stuff is scaring me out of using my dishwasher...


Take the front panel off and you will see the dispenser tank. Remove and clean. ... Bosch 24 in. SHY66C02 / SHY66C06 Built-in Dishwasher

I have a GE dishwasher model GLDL560N10SS. I noticed a burning smell coming from it the other day and then realized that although I can hear water running into the dishwasher when I start it, it never actually runs in the sense that the water is pushed through the various outlets to wash the dishes. I'm assuming that it is because the unit is dry and the heating element is still coming on that it is causing a burning smell. If I open the unit and reset it, it pumps the water back out into the si


The problem sounds like it is in the water inlet selonoid. Pull off the bottom panel and this is the part that the main water line hooks to there is a selonoid and it has a plugg inconnection to it unplugg it and check for power when the unit is supp ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2266 seconds