Having problems with your AEG 24 in. Favorit 50730W Free-standing Dishwasher ?

Powder solenoid I hav e an AEG Favorit 50700 sensorlogic dishwasher. As soon as I switch on, before even selecting a programme, the solenoid to operate the powder dispenser door operates, then stays activated until I remove power. I've taken the door liner off and the PCB looks OK - but I guess whatever powers up this solenoid has gone short circuit. Any idea what it might be or might look like?


Answers :

Probably the main module ie the pcb you were looking at
The no-brainer answer is to replace the controller board. But I just saw the price on line was 248GBP ($350) which is not going to be worthwhile. I just had the same problem with the same model dishwasher. When I checked my circuit board under a microscope, I saw cracking and discoloration on what appears to be a ceramic capacitor. It looks like this capacitor is for snubbing the transient across the triac used to control the soap dispenser solenoid. I do not know what value this capacitor has, but I am about to replace it with a 47nF, 630V ceramic capacitor in a 1206 package. That costs $0.59 from digi-key (part number 445-8794-1-ND) I am sure that Colin999 has trashed his dishwasher by now since he posted his question over 4 years ago. I will post an update with the results when I get the part installed.
Repair Help & Product Troubleshooting for AEG 24 in. Favorit 50730W Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Powder solenoid I hav e an AEG Favorit 50700 sensorlogic dishwasher. As soon as I switch on, before even selecting a programme, the solenoid to operate the powder dispenser door operates, then stays activated until I remove power. I've taken the door liner off and the PCB looks OK - but I guess whatever powers up this solenoid has gone short circuit. Any idea what it might be or might look like?


Probably the main module ie the pcb you were looking at ... AEG 24 in. Favorit 50730W Free-standing Dishwasher

Smeg e2 error (water level tripped). Filter is clean and no rubbish below filter on inside of dishwasher. I have taken the front panel off but am not sure where the float device is located - I am wondering if it is just to the left of what looks like a solenoid. There is no water in the base of the unit in the front panel so would rule out any leaks. Reset program and turned off power at socket but still not using hot water. Possible PCB issue ? Any advice appreciated. Smeg DI612C Dishwasher.


... Dishwashers

I have a Kenmore Ultra Dishwasher. Model # 665 or 655. 15895791. A peice fell off the upper middle area. Its round and has 2 concave areas on it. It looks loke it might spin and distribute water. Ive tried to put it back on, but there must be a part missing. Ihave looked and looked online for this part but have not found it. Also I am even having a hard time with the model #. Ive checked it several times to see if I read it wrong. Thanks in advace.


... Kenmore Dishwashers

My dishwasher, a Whirlpool DWF B10, is not cleaning properly. When the cycle has finished, there is always a block of undissolved dishwasher tablet/powder left behind. My guess is that the seal to the powder door has gone and allowing the tablet to get wet too early and part dissolve before the door opens - is this likely to be right? If so, can I get a replacement seal or do I have to replace the whole powder & rinse aid containers ??


... Whirlpool Dishwashers

I have a Maytag DWU8250BAX and the thing leaks like crazy. I just replaced the door gasket, but that is not the problem. When I took a closer look at the door it seems as though the water is getting up and into the door through a space in the bottom of the door. It seems to me like there should be another door seal to fill a gap that sits between the door hinges. If anyone knows if there should be a seal here and then what the part number might be that would be great. Thanks!


There is an airgap under the door..it should spray up and run down the door not spray up under it..look for crack or hole in spray arm..if there is the wrong soap in it it will flood out with lots of bubbles..just have to flush it out. lastly, if you ... Dishwashers

Hello! I have a Kenmore Dishwasher Model # 665.15805890. The dishwasher came with the house and I'm guessing it is around 10 years old. My toddler was having a great time flipping the door to the soap dispenser back and forth until he pulled the door off of the pin. Now, I can't seem to position the spring in a way so that the door will spring back. I never looked closely at the hinge before, so I don't know if that is the only reason the door will not release the detergent, or if something


Hi.Please see if the diagram here can help you. Check if the spring is that indicated with nr ten in diagram. ... Kenmore Dishwashers

I'm trying to fix a whirlpool du980qpdq6 dishwasher. The door on the soap dispenser won't open. I've checked the latch and it works...no blockage. I've taken the door apart and looked at the Wax motor in the door. Apparently that is what actuates the mechanism that opens the door. Does anyone know how to test the wax motor to see if it is functioning?


... Dishwashers

I have a 13-year-old Maytag DWU9906BAE. It has worked well but the door now opens too far - about 20 degrees lower than horizontal. I've taken the door apart and the reason is that the upright part of the two L-shaped hinge plates no longer catch on the back of the door jamb; for some reason they are now angled too far out and miss the catch plate on the back of the jamb completely. I'm no expert but they don't look warped, nor does the frame that they attach to. They're made of stamped


... Maytag Dishwashers

Door wont close - I have taken off hinges and they look ok. Is it possible that the hinge opening on the inner door has been stretched when I overextended the door with heavy turkey pot


It is very likely the control lock has been set on the oven. This means the door latch is unable to enagage with the oven lock. If you have turned off the power at the circuit breaker and there is no change, then you may try the Cancel button on the ... KitchenAid 24 in. Built-In Superba Series Dishwasher w/ ProScrub Built-in Dishwasher

Door dropped Opened door on my FDB421RFR and a loud cracking noise occurred - now the door drops quickly. I guess the spring(s) have broken - does anyone know if the spring is on the rhs looking at the front? I sure hope so, I can probably access that side without pulling the unit out! Is it good to spray these with WD-40 or do they just age anyway?


... Frigidaire 24 in. FDB421RF Built-in Dishwasher

Frigidaire microcycle ; part no: f3885m Can you please explaine where the dish washer powder goes in on this model? It is an older model which has 2 large plastic circle domes and a scew top clear bung on the inside of the door but dos not explain where to fill with powder!!! Look forward to response pls


... Frigidaire Dishwashers

I had a service tech at my house to repair my refrigerator. He also took a look at my Maytag WU504 dishwaser, which was not cleaning the dishes anymore. He was less familiar with dishwasher diagnosis, but found that the lower spray arm was pumping out water through the jets properly in the cycles, but that the spray arm was not rotating. He seemed stumped and called his supervisor, who suggested it might be the wash impeller. I have looked at the parts diagram on partselectdotcom and taken t


You are absolutely correct!!\015\012\015\012The support retaining nut allows the arm to spin without falling off.\015\012\015\012And it would definately cause dishes not to clean if the arm didnt rotate.\015\012\01 ... Dishwashers

LG LDF8812ST dishwasher not washing: reports LE error code. Fills and drains ok. Impeller is clear, removed inside housing - no obstructions. Synchronous motor works. Tested main motor - appears to be good. Motor is not locked, looks to be in excellent condition. No shorts to ground, continuity across three main pins - not sure what the other 4 are for. My guess would be the PCB, but not sure how to test this. How do I determine if the PCB is bad?


... LG LDF9810ST Built-in Dishwasher

We have a Hobart dish washer in our bar area and when it sits over night there is a pool of water on the floor in the morning. When we open the door and look at the upper right corner in the rear of the machine we have a steady flow of water running down the rear wall. When looking at thge machine where the black 1 inch water hose comes up from the floor there is a plastic T in the line with an electric wire the goes into the side of the T. I am guessing tha that is a sensor valve that is suppos


The model is most likley a lx18,lx30,lx40.The fill solenoid valve is stuck open.Remove the 2 screws on the bottom front where the pressure gauge is.Turn the circuit breaker off.When you remove the cover you will see a bronze valve with a red hose goi ... Hobart Dishwashers

Whirlpool ADG 7550 integrated dishwasher not cleaning properly. Ive checked the filter and there are no signs of blockage. There is no unusual beeping but there is however a weird motor noise that just appeared. Dishwasher appears to run through the cycles but most of the time there is still traces of food left behind. It takes about 3-4 washes to clean the plates. Sometimes there is a lot of soap residue left around the release door which leads me to believe there might be a pump issue? ive ope


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Whirlpool 24 in. ADG7540 Built-in Dishwasher

Dishwasher (Whirlpool Model DU930PWQ0) won't pump out. Problem occurred after door was opened during a cycle. Then the pump-out function ceased to work. Washer fills and pumps correctly during the wash cycle. Any suggestions? My guess is that the electronic control may be faulty and it is not opening the solenoid valve for the drain cycle. The other option I have thought of is that the solenoid valve may be faulty and is not responding to the signal from the controller. The dishwasher is n


... Whirlpool DU930 Built-in Dishwasher

The door on my built in Frigidaire dishwasher is falling open. it seems like a spsring or something has broken. I am looking for a repair manual, possibly an exploded diagram so that I can see what parts i might need. Thank you, Brenda


Here is the way the springs hook up.\015\012\015\012\015\012Here is the break down.\015\012 ... Frigidaire Dishwashers

Not draining had water pooling at bottom of dishwasher. i've taken apart as much as i know how to but can't figure out how to get the last piece out - where the little wheel is located i guess used to flow water? lines look clean


The drain pump is separate from the was motor and is accesed from underneath the dishwasher that help wash moter is one piece and is replaced as a whole unit and the drain hose comes from the factory making a loop up side the tub a lot of installers ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I have a model 5000g. it might have 15 hrs. total running time on it. when i tried to use it last it would not build pressure. i took the pump apart and cleaned and regreased it. everything looked good. ive got good pressure to the pump but just a small spray out the wand. when running there is no real load on the engine. it has always been kept inside in a warm enviorment.


... Karcher Pressure Washers

As noted on this webpage, we, too, have an intermittent leak out of the left side of our dishwasher door. We had a repair person look at it who suggested we might had inadvertently not rinsed regular dish soap off the dishes, but this is not the case today. Any suggestions? It's kitchenaid dishwasher model KUDS10IV, purchased 1/25/10.


... KitchenAid KUDS30IV Builtin Dishwasher

The Dishwasher PLD2850RDC2 will not start. The CL flashes, the type of cycle pressed on the key pad does respond, but nothing happens when START is pressed. Steps taken: -Door is clicked shut -Power breaker has been turned off and back on -All dishwasher moving parts have been moved by hand to ensure no obstructions are in the way. Best guess is the key pad is just non responsive. I hope there is an easy solution. Thank you.


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

GU980 dishwasher I have a buzzing sound when the washer is in drain mode. The manual indicates there might be something in the Power Clean Filter, and that it will go away when the object grinds up. I called Whirpool, and they said the same, and to run for 2-3 cycles to make go away. 2-3 cyles later, noise is still there. I noticed a nub off the rack that looks like an end peice of metal broke off from rust. My guess is it's stuck in the PCF, and will not grind up. I removed the nut, lower spray


The nut holding the inpeller has to come off it is probally frozen\015\012if it snaps off then the pump assy willl have to be replaced or at least the motor, you need to get below the impeller to see what is down there though, or let it run as ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Dishwasher problem Hi We have a Whirlpool GU 2300, the machine has stopped and is the clean LED on the control panel is showing a 7 pulse sequence which I guess is a fault alarm. I have tried resetting, checked the door switch and looked at the pressure sensor at the drain pump outlet. I changed the heating element and fitted an uprated control card earlier this year. Any ideas?


I solved the reset by pressing the air dry and reset buttons 6 times in sequence, the whole panel array lit and I was then able to reset. I have had no problems since and have used it 6 times. I initially thought that the chipset had a volatile memor ... Dishwashers

1987 In-Sink-Erator Classic Supreme (Just like KitchenAid from that era) - leaked Jet Dry after it was filled. Haven't taken door apart yet to figure out what is wrong. Also, after washing/rinse/dry is complete, dishes have light coating of white powder-like film that wipes off. What could be the cause(s) of these issues?


You have to replace the rinse aid compartment if not the whole inside door shell ,the reason for the coating is because your not using rinse aid.If you are using the same soap than you need to replace the leaking dispensor. ... KitchenAid Dishwashers

Maytag mdb8600 I am replacing the latch mechanism and have 3 wiring connectors. Not sure how to connect them back to the new latch. The first one has 4 white wires, the second one has 4 black wires and the other has 2 black and one purple wire and attaches near the top of the door....I was looking for a wiring diagram but hoping you might be able to help


... Maytag 24 in. MDB8600AW Jetclean II Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1226 seconds