Having problems with your AEG 24 in. Favorit 60820W Free-standing Dishwasher ?

My Aeg dishwasher keeps coming up witha C2 fault code

\015 I think that it might be the drain motro that has gone as it fills up ok but hwen it comes to the draining out the code comes up\015

Answers :

The pump out motor in line with the outlet pipe could be faulty. Remove the moto and connect it to the mains for a few seconds. The motor should spin and the impeler inside the motor should spin freely. If the motor is faulty it would not work and must be replaced
Repair Help & Product Troubleshooting for AEG 24 in. Favorit 60820W Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Aeg dishwasher keeps coming up witha C2 fault code


The pump out motor in line with the outlet pipe could be faulty. Remove the moto and connect it to the mains for a few seconds. The motor should spin and the impeler inside the motor should spin freely. If the motor is faulty it would not work and mu ... AEG 24 in. Favorit 60820W Free-standing Dishwasher

Dishwasher does not drain all water after wash, code C=drain hose,coase or fine strainer or sink blocked.(all checked & are ok) then towards end of wash code H= Call AEG service force ,comes up. but if i put machine on pre-rinse it driains ok, so pump is working. only seem's to be end of wash programe fault accurs


... AEG 22 in. Favorit 55750IM Built-in Dishwasher

I have a Fisher and Paykel DD24D Dishwasher just installed and the fault code U keeps coming on, which says no water, I checked the water supply, it is try on, so now I'm at a lost.....thanks


If the unit is new do not try fix it or have it fixed, or even look into it, call the dealer or take it back to him as you will invalidate your warranty if you do anything to the unit, and that is not worth it. Let the dealer worry about it. ... Fisher and Paykel DD24D Dishwasher

I have an IAG dishwasher that keeps stopping on cycles before the dishes are dry and coming up with error code E7 which asks me to rerun cycle and if code appears again contact maintenance. Any suggestions on what code E7 means


... Dishwashers

WATER FAULT OUTLET CODE COMES ON ON ASKO DISHWASHER


... Bosch Dishwashers

E4 code has come up on my Campomatic dishwasher, and the dishwasher keeps tripping out. Please help.


... Dishwashers

My Miele g1430 dishwasher keeps coming up with an F12 code I have cleaned the filter and there is good water presure and the valve seems to be pulsing but always comes back with F12


... Dishwashers

We have a LG dishwasher LD-14AT2 and the rotating arm that is attached to the end of the lower wash arm keeps on falling off. a) how do we fix this? and b) would this be causing the dishwasher to come up with an E1 error code?


The lower arm is attached with a nylon nut to a nylon hollow shaft the water comes threw, u can try replacing the nut 1st then if it comes loose again you will need to replace the arm the that the spray arm connects to. as far as the E1 codee goes it ... Dishwashers

Hi My fdw70 dishwasher blew and smoke started coming out > I replaced the fuse and it was fine for a couple of cycles and now keeps coming up with the A10 error code . what part shall I change where is it and what does it look like > Cheers James


... Dishwashers

Kleenmaid dishwasher I have a problem with my dishwasher it keeps coming up with the fault D04


Try unplugging it for 10-15 seconds ... Dishwashers

New World DW60 dishwasher not working originally had E4 fault Power comes into the PCB the switches and led's light up but nothing happens. After about 5 mins there is a short beep. Does not show any error codes, New World sent a replacement PCB which made no difference except now have no error code. Circ pump, inlet valve, heater, drain pump checked independantly all worked.


I f you have warranty on this please call them, you have a defective\015\012D/W.Unless there is no charge for repairs ,don't spend a dollar on what\015\012is going to be a on going problem ahead.To explain how to fix this is\015\012what the manufactu ... Dishwashers

Recurring .30 fault on AEG dishwasher. Have tried pulling out machine and tilting back 45 degrees but fault clears and then comes back on next wash. Is there anything else I can do?


This is caused by the Anti-Flood device at the base of the machiene being activated. This device detects water leaks and is a polystireene float / micro switch that puts the machiene in pump out mode only. You need to determine where the leak comes f ... AEG 24 in. Favorit 60830 Free-standing Dishwasher

Fault codes 40760 aeg dishwasher - Dishwashers


... Dishwashers

I have a miele g2220 sci dishwasher. keeps stopping during cycle and displays fault code F14 which is not in the manual. please help.


The clogged circulation pump (error code F14) ... Miele Dishwashers

Fault code 30 has come up on my dishwasher how do i fix it


-30 is a leak in the system and is filling up the drip tray at the bottom. The float is attached to a micro switch and will halt the program and start the pump to drain the washer. You can tell by feeling in under the tray for water. ... Electrolux 24 in. EDW5505EPS Stainless Steel Built-in Dishwasher

Hi, on my WAE8987 Washing machine, the fault code 'F07' keeps coming up, can anyone help please? thanks


Bauknecht are built by Whirlpool.\015\012\015\012F7 on Whirlpool means flow meter failure.\015\012\015\012Check water inlet, check the pressure switch, and check the sump filter at the bottom of the dishwasher.\015\012\ ... Bauknecht Dishwashers

I have AEG Favorit 80800u dishwasher type 45_1 VCD 24 which keeps dropping power off after 10 minutes of operation. No Leds nor error codes. Power enters the unit properly.


Have you monitored the the power while the machine is running? Does the power supply receive constant voltage? Or does the power supply shut off?Can you tell where the power begins and ends? That kind of testing will be necessary to find out. ... Dishwashers

Keeps coming up with fault "F1" - Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher


Is that in one drawer or both?\015\012\015\012Generally it means the flood switch under the drawer (inside the housing is activated). This means water is leaking from somewhere - foam in detergent, cracked or crinked hoses, door seal leak ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My bosch excel dishwasher has the following fault: start the cycle, water starts to fill but then check water light comes on and it then starts to empty again. Pump then keeps going. I have checked the hose and even swapped it round with my washing machine one but this makes no difference. I have cleaned all the filters and taken off the cover to check the 'propeller' as sugested in the instruction manual. But no joy - check water light still illuminated and willnot continue with cycle. - Help!!


This unit im sure has a water flowmeter that measures the water intake.. if this cannot read then the unit shuts down to avoid flooding.. \015\012it needs replacing... it is attached between the valve and the side tank or attached to the tank d ... Bosch Dishwashers

Dishwasher beeps constantly and gives fault code that the flood switch has been activated. Neither drawer will trun off. It seems the fan keeps going, and is very noisy. It worked fine last night.


Hello there:here is some ideas that will help you clean off the flood switch thatis causing the error first unplug the power going to the machine If you by accident overloaded the top drawer\015\012and this will allow water to ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

Aeg-electrolux favorit 88070vi dishwasher comes up with error code i30 please help


... Dishwashers

OE Code keeps coming on screen LG Dishwasher LDS5811WW


OE error message is listed in the manual as a drainage problem so first I would check for a clogged line ... LG 24 in. LDS 5811ST Stainless Steel Built-in Dishwasher

Dacor mdw24s close door code lights keep coming on stopping dishwasher and the door is closed and latched, and problem is not the door switch or latch


The issue is the controller board seems not to be insulated and then the glue from the connector that holds the power to the board comes apart from the heat of the wash.  I removed the board, resoldered it (power cables are the black ones) and i ... Dishwashers

Kenwood dishwasher keeps stopping with E4 fault code. have tipped to 45 degrees to release excess water and its ok for 2-3 washes, then repeats problem.


Disconnect power to your dishwasher or unplug the power cord.for a few minutes. open up your control board check if water spilled on it. Dry the liquid. assemble it back. be careful not to mis fixed the harness wires.\015\012\015\012plug ... Dishwashers

ASKO 1595 daer greendude, indeed your troubleshooting was right!!!! i pulled out the dishwasher and the base was full of water. once i got water out, the fault sign went away and it's ready to run its normal cycle. now i need to figure out where the leak comes from: either the fitting or the valve itself. just in case i have to replace the valve: any good source to get it from? i live in california. once again, thank you much!!! i'll keep you posted on the developments


I live in australia our part no is 8052120 ... Asko D1776 Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1673 seconds