Having problems with your AEG 24 in. Favorit 80820 Free-standing Dishwasher ?

AEG Favorit 80820 dishwasher tablet door opens as soon as switched on and door closed. When you put the power on and select a wash and then close the door the small grey dishwasher tablet inside the door can be heard to open as soon as the door is closed. Normally this door remains closed until asked to opened automatically by the dishwasher at the correct point in the selected wash program.


Answers :

Repair Help & Product Troubleshooting for AEG 24 in. Favorit 80820 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

AEG Favorit 80820 dishwasher tablet door opens as soon as switched on and door closed. When you put the power on and select a wash and then close the door the small grey dishwasher tablet inside the door can be heard to open as soon as the door is closed. Normally this door remains closed until asked to opened automatically by the dishwasher at the correct point in the selected wash program.


... AEG 24 in. Favorit 80820 Free-standing Dishwasher

I have a bosch dishwasher model number SGS0902GB/05. I use tablets instead of detergent. I put the tablet in the Dispenser and close the lid, noproblem. I then set the programme and shut the door, I usually set the programme to delay start so that it washes dishes in the small hours when all are in bed, however, when I have set the programme and close the door within a minute the dispenser assembly opens and the tablet falls into the dishwasher, I then try and put the tablet back in the dispe


Hello Andrew,\015\012\015\012I'm more than happy to give step-by-step instructions for replacing the detergent dispenser, however it's not cheap (about \302\24350) and it probably doesn't need to be replaced. Some of the smaller component ... Bosch Dishwashers

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

Cranky dishwasher I have to admit my wife's solution is the only one that works. Our ten-year-old Superba built-in usually starts a normal cycle part-way through, at the wash part, without filling or opening the dispenser door. Therefore the dishes come out with the soil now baked on. Closing the door, selecting normal and start results in a pump-out sound, or at least just the pump running to wash the dishes. The dishwasher ignores any cancel button push,and the light does not come on over t


You want to make sure that the dishwasher is level and secure first of all. Then I would look into the door latch assy. Sounds to me that you are not making all the latch switches when closing normally. When you are slamming it, you are making the s ... KitchenAid KUDS24SE Built-in Dishwasher

Kenwood Elite Dishwasher Mod#665.13779 K600 "Normal Wash " light blinks continuously with NO washer action. No other wash modes light up when pressed. Washer does not do anything. However, a couple of times I got it to make a noise as if it was draining, but then nothing happens. Push "Cancel" and it blinks in unison with Normal Wash light. Open door and close it, "Cancel" light goes out and Normal Wash light continues to blink. Have tried various combination of buttons to try to "Reset"


... Kenmore Dishwashers

My whirlpool dishwasher type 280-2 detergent door will not open during wash cycle. Yes the compartment, springs and door are thoroughly clean. Will not open if I just close the door and remains empty. I'm wondering if perhaps I knocked off some random part that makes it open. So please tell me how darn thing opens and perhaps a pic of the parts so I could see if ones missing. Thank you for any help offered for this, its driving me nuts.


... Dishwashers

We recently installed a Kenmore dishwasher, Mfr Model# 13943. We have used the dishwasher approximately six times since Thanksgiving. Each time, after the wash cycle is complete, when we open the door, water has collected on the interior of the door, and water remains standing on some of the washed dishes. Is this normal?


... Kenmore Dishwashers

Prima lpr601 problem- filled dishwasher up sa normal set the wash pressed button on far right (dont know what it is but needs to be done), closed door and loud raattling so i opened door to make sure all spray arms were clear which they were, closed the door , again the rattling . now the green light has gone out on far right and cant get it back on so program wont start at all. Any advice?? please help


... Dishwashers

My 1yo slimline hotpoint dishwasher LST216 has developed a fault when trying to run the 'normal wash': washing stops after a couple of mins, the lights start flashing and the alarm comes on as soon as the water is being drawn into the machine. When I open the door I can hear a whirling/grating motor noise coming from the bottom of the machine. I have cleaned all filters and have run other programmes to check overall functionality and they all work as expected most of the time. I cannot unders


... Hotpoint Dishwashers

The dishwasher has the normal and economy wash lights flashing and after we hold the start button down for 4 seconds the stop and then return to flashing? The washer motor runs when the door is closed and no water comes out and the system doens't stop trunning until the door is opened. The system ran for over 4 hours yesterday. Viking Professional


Hello, welcome to ... Viking 24 in. Professional Series VUD040 Stainless Steel (Premium) Built-in Dishwasher

I am getting a clicking/ticking noise (1 click/second) from my Maytag (model MDB9100)dishwasher after it goes through its auto clean normal wash cycle. At the end of the cycle the arrow = clean and the clicking sound is there. I opened the washer door for about 1 minute noted the soap containers are empty, dishes clean, machine still hot/steamy. Closed the washer door and the clicking sound resumes. Please advise.


This is the heated dry timer going through the drying cycle until the dishes are dry. The dry cycle runs on a timer and it will click through the cycle until it finishes the amount of time preset on the timer to dry the dishes. ... Maytag MDB9100A Dishwasher

Hi, The machine will not complete a cycle. I think it may have started when the power was turned off at the mains during a cycle. Symptoms are : - You can turn machine on, select a program, press start button, close door, machine appears to begin cycle as normal, water seems to load, then 2 minutes later drains, and 1 minute or so after that the machine beeps 3 times to indicate cycle is finished. Dishwasher tablet door never opens, dishes not cleaned. Have tried : - cleaning filters; - turn


It is likely the dishwasher is locked in some diagnostic program.\015\012If you provide the dishwasher model no. then I can try to find out the keys you need to press to get it out from it. ... Whirlpool Dishwashers

My soap cap remains in the closed position at all times. The clasp mechanism works fine, if I cycle through with the door open I can see and hear the catch release when it should. But the door remains closed at all times. I leave it open to run, and sometimes it's closed when the wash cycle finishes! Is there an easy way to take the cap off and clean it? Or do I need to WD-40 around it?


There is a little spring in there that flips the door open, just take the screws off of the side of the door, you'll see the broken spring by the door, make sure power is off to dishwasher ... GE Nautilus 24" Built-in Dishwasher

I HAVE A BUILTIN KITCHENAID SUERA DISHWASHER WHICH IS ABOUT 14 YEARS OLD IT SEEMS TO WORK PRETTY WELL. BUT THE SOAP DISPNSER DORRS TICK CLOSED SO THE DISHWASHER FINISHED AND THE DOORS REMAND CLOSE SO THE ONLY WASHING IS DONE WITH WATER AND NO SOAP. THE SOAR DOOR HAS TWO SLIDING DOOR THAT ARE ARC SHAPPED AND SEEME TO BE CONECTED WITH BUTTONS ATH THE CENTER. THE SOAP DISPENSER ID AHITE INJECTION MOLDED PLASTIC ANDY IDEA I CAN TRY TO GET THEM TO OPEN DURING WASHING CYCLE THANKS **** VON ROTH


Water does not come into the washer ... KitchenAid 24 in. KUDP02CR Built-in Dishwasher

Have Whirlpool dishwasher Gold Series, Model GU9805CGB1 which stops part way through wash cycle with the led indicator blinks on the normal cycle.....if we ope nthe door and shut ...it continues until part way through rinse cycle...stops again....led indicator blinks again.....we open the door & shut and it continues....but then continues to run through the normal wash cycle continuously.....until we open the door again.....what's wrong???


Sounds like the door is losing contact with the door switch, first thing i would check is the door strike.Metal strike plate located on the tub itself that the door latch catches as it closes. its a spring metal striker, i would try bending it down ... Dishwashers

Maytag model mdbtt70aww. After the end cycle. open the door and found detergent tab on the bottom and the main wash cover is opened. Maytag diswasher model MDBTT70AWW. Put dishes and so forth in the dishwasher. Put detergent tab and jet-dry rinse agent in the pre-wash section. and close the cover. Start wash cycle after done over door and found the detergent tab on the bottom new the heater. The cover to the main wash is opened. Dishes are are clean. Wish someone would tell me


... Dishwashers

Dishwasher Normally, after the dishwasher cleans the load, it displays green light next to clean. Once the door is opened, the light goes off an dishwasher is ready for next load. But from few days, after opening the dishwasher door, the clean light does not go off, it remains lit. Dishwasher doe snot reset for next cycle. So, I have to go in the basement and trip the main power to dishwasher. That resets the dishwasher. This needs to be done before each cycle. Not sure how to resolve the issue.


Make sure that you do not open the door during the wash cycle. Wait until all the cycles \015\012are complete before opening the door. Especially don't open the door \015\012during the drying cycle. ... Dishwashers

Kenmore 665.16529000 When we put the dial to pots and pans the diswasher fills up and cycles through, when the dials moves to normal wash, it fills up and cycles through again. When the dial gets to light wsh we can hear the motor running but nothing is happening, but the soap door opens soon after. The heating light comes on and the inside of the dishwasher gets so hot that it has melted our big plastic tumbler cups on the top rack and makes the counter top extremely hot to the touch. The dial


... Dishwashers

LG DISHWASHER THE DETERGENT TABLET WON'T POP-OUT DURING WASH CYCLE, WHEN THE DOOR IS OPENED ITS STILL INTACT, AND DISHES ARE LEFT DIRTY AFTER NORMAL CYCLE.


This is a common fault if your drain hose or the drain pipework after it is blocked by tissues or fluff etc remove the drain hose from the vertical drain pipe or u-bend connection and check that all are free of obstructions. Also a lot of machines ha ... LG 24 in. LD-12BW5 Free-standing Dishwasher

Soap dipenser My whirlpool built-in dishwasher model DU930PWPB0 serial # FR4104078. The door to the soap dispenser will not open. I have been washing the dishes with the door open all the time. When I close it(door) it won't pop open when it should. to dispense the soap in the wash cycle.


Try this... Wipe out the soap dish with white vinegar and a soft cloth.. make sure you get everything off the edges of the door and look for any nicks, blemishes or deformation of the dispenser door to make sure it is not mechanically binding up when ... Whirlpool 24 in. DU930PWP Built-in Dishwasher

Bosch Shu43C02UC dishwasher fills with water but the washing won't start. As the filling nears complete, a double clicking noise occurs to start the washing motor but nothing happens. The time continues to countdown but the machine is silent. When I open and close the door, the click click noise is heard but the machine is silent. I can cancel the cycle and drain the water but none of the washing or rinse cycles will activate but the timer works. The soap door even opens if the timer is left to


Have you checked the inlet water temperature is at the correct level for the dishwasher.\015\012\015\012Please provide the full model no. of your dishwasher -- Shu43C02UC /??\015\012\015\012I think the problem is linked to th ... Bosch 24 in. SHU43 Built-in Dishwasher

I live in Corfu Greece, I have dishwasher LSE 830 ST, Which I bought here in Greece. I have a message saying Door Open when the door is closed. I have had this message for few weeks now but normally it goes after few times of opening and closing door, can this be fixed? Regards BJ Tarrant


... Ariston Technologies Dishwashers

I've had an LG LDF6810ST dishwasher for about three years with no problems. All of a sudden it won't close. It finished the wash, I emptied it, and when I went to close the door it wouldn't close all the way. It was as if something was getting caught not allowing the door to close completely. I searched and found nothing blocking, then I looked at the door latch and it looks as if the child lock feature is engaged. So the door is locked while open. I turned the child lock on and off through the


If all else fails.... kick it! at least you will feel better! ... LG LDF6810ST Stainless Steel Built-in Dishwasher

I set my dishwasher to wash last night (delay 2 hrs.) and I checked it this morning and it never washed. Yesterday, I had to turn off the dishwasher at the breaker box because it wouldn't reset. Now, the normal wash and heated dry lights are on, but it won't start. Also, it usually beeps when I close the dishwasher door, and now it won't even do that. We bought the dishwasher about a week ago. It a GE Profile dishwasher. Thanks, Chris


\015\012\015\012\015\012First off all try to close the door tightly with your hand till you hear a beep.dont force very much.\015\012as you mentioned that unit normally gives a beep when door is closed.but not it is not giving that beep w ... GE Dishwashers

The three lights for Pots & Pans, Normal Wash, Econo Wash are all flashing. When I hold the start button down for four seconds, just the Normal light is on. However, once I close the door, all three lights are on again, and the dishwasher does not start. We have tried unpugging it and then plugging it in again. It worked once then went back to all three light flashing. Before this, only the Normal Wash and Econo Wash lights were flashing.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I can't seem to access any previous post dialog that may have taken place but I'd like to help if you can fill me in on whats taken place to this point.\015\012\015\012The scenario you describe i ... Viking DFB450 Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2037 seconds