Having problems with your AEG 24 in. Favorit 80860iW Built-in Dishwasher ?

I have an AEG Electrolux 80860 (free standing). It is not cleaning properly and keeps saying 'spray arm blocked'. I'm not sure what to do. I have run it on empty, tried to unblock everything I can see (spray arms don't have much to clear - only tiny holes and they look ok). Do you have any suggestions? Many thanks!


Answers :

Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works like new... However I have also foundthat if the heating element goes bad then that also can mess things up bad...So I would buy new spray arms, and also check out the heating element to makesure it is working... Here is a tip that will help you with the onlinebuying...\012
Dishwasher SprayArms not Spinning

How to Buy ApplianceParts Online

A bad heating element causes many problems in dishwashers...

Dishwasher Problems The HeatingElement not Working

DishwasherMaintenance\012DishwasherResidue and Film on Dishes\012

heatman101

Asker's Testimonial "explanation very clear. will give it a go and see howsimple it was. thanks Ronnie " - ronnieshomes
\012
\012;\012';';\012;
Repair Help & Product Troubleshooting for AEG 24 in. Favorit 80860iW Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have an AEG Electrolux 80860 (free standing). It is not cleaning properly and keeps saying 'spray arm blocked'. I'm not sure what to do. I have run it on empty, tried to unblock everything I can see (spray arms don't have much to clear - only tiny holes and they look ok). Do you have any suggestions? Many thanks!


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... AEG 24 in. Favorit 80860iW Built-in Dishwasher

I am not getting any water out of the bottom spray arm in my bosch SGS47E02GB35 dishwasher. I have cleaned out the plastic pipe assembly on the left hand side of the machine and the plastic tubes that sit to the right of the pipes. I have blown through many of the other pipes to and dislodged quite a lot of debris which has now been cleared out of the machine. The machine completes its cycle and water comes out of the upper spray arm (there may not be as much water coming out as there should be)


1. Check that water can flow from main pump,though hose to propellor,that there is no blockage. ... Bosch Dishwashers

I have a maytag MDB600AWW dishwasher. the top spray arm doesn't turn. it wouldn't even turn if i removed the to middle trays. I took the accumulator out and cleaned it. the fine mesh filters were clogged. unfortunately, birthday candles found their way into the machine sometime back. i cleared as much as i could. when i put it back together, the top arm would spin only when i had the 2 middle arms disconnected. It seemed there was an increase in pressure. i ran a diagnostics test and there were


First check to see if the washarm itself is clogged, if so clean it out.\015\012\015\012If the arm has a bearing it may be shot.\015\012\015\012You may have a clogged manifold on the output side of the pump. I sometimes run a ... Dishwashers

Asko 1353 dishwasher is no longer cleaning. It cycles and runs but make a tremendous amount of noise, like the pump isn't working properly. If I open it while it's running I done see the same amount of water being sprayed from the two spinning jet arms. There's 'some' water being sprayed but nowhere near as much as before.


... Dishwashers

My Whirlpool Gold dishwasher has been wonderful until recently. In the last 2-3 weeks, the top rack of dishes does NOT get clean - AT ALL. It appears that the spray arm is not moving, or at least not moving much. What can I do myself to check this out and possibly take things apart to see if something is clogged?


Take a tork #20 screwdriver and remove the screen go all the way to the choper and make sure its not broken on clogged. ... Dishwashers

Prima lpr601 problem- filled dishwasher up sa normal set the wash pressed button on far right (dont know what it is but needs to be done), closed door and loud raattling so i opened door to make sure all spray arms were clear which they were, closed the door , again the rattling . now the green light has gone out on far right and cant get it back on so program wont start at all. Any advice?? please help


... Dishwashers

- the dishes and glassware on the top rack are not coming out clean - I checked the course strainer to see if it is being blocked but don't see any thing there - I also took out the spray arm that sprays up into the top rack and ran water through it with a hose - it also appears to be free of clogs. - I don't see the spray arm spinning when I open the door during the wash cycle - - lastly, it may be unrelated, but the dishes are not coming out of the washer as hot as they used to be any i


... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher

I have a GE Profile, GSD4930X73WW, dishwasher. The upper wash arm is not spraying well at all. I checked the water line from the pump to the upper arm and it's fine. I cleared the filters and cleaned the float. I also took the inlet valve off and cleaned the screen. Although the washer works better overall, the upper arm still does not work well. Nothing appears to be in the upper arm assy to clog water from spraying out. All seems clear from the turbid sensor (next to the pump) through t


... GE Dishwashers

Hi I have a Nemo Dishwasher and the top spray arm is not turning. The bottom one is going fine and there is certainly plenty of water getting into the washer as I opened the door with the washer going and it flood me. I can see the water getting into both spray arms - the bottom one has a excellent upward spray and turns - the upper spray arm has water getting into it but it will not turn. I have cleaned the dishwasher out and any internal parts that I could find so it is spotless - this is so f


... Fisher and Paykel DS602 Dishwasher

I think I am finding small pieces of the wrap from the tablets in the small holes in the spray arms, one wont move anymore??? This is about 10 yr old maytag machine. I tried to clean out the spray arms but dont really know what I am doing. Bought a new diswasher, dont want to use the tablets if they will clog up the works. please advise.


Just prime the sink before you start the dish washer ... Maytag Jetclean II MDB8551A Dishwasher

Danby DDW396W-2 Spray arm won't turn have checked pump, appears to work, spray arm is clean, drain hole clear, lines clear, HELP


I have had a similar problem numerous times, a couple of which required\015\012manoeuvreing it into a place I could work on it, and a laborious\015\012removal of the covers. Each time, up until this current incident, the\015\012solution that worked, ... Danby 22 in. DDW396 Free-standing Dishwasher

Hi, my hotpoint aquarius df61 makes all the noises of washing, i hear the water going in, motor is running, however i dont believe the spray arms are revolving, so the dishes are not getting clean. i have cleaned the individual holes in the spray arms, but i don't think the water is getting up the back pipe and into the top spray arm. it does not spin at all. no problems draining. help please. and were can i get a copy of the user guide, free preferably. thanks


How old is your machine? it is posible to have something in the watwr pump, you hear the water and the motor, but the fan of the pump (washing pump) is blocket. also the pipes hat make connection to the water pump and the arms. at someoane i found gl ... Dishwashers

Hi I have a Kenmore model 13742k. The dishes in the upper tray are not getting cleaned. The upper spray arm is not circulating. I dissassembled the components from the base leading up to the spray arm but there is no clogging. Water does flow out of the spray arm but prob not enough to turn it. The turbo components are clear as well. Any ideas? Thanks Richard


The top rack is not cleaning because of low water pressure from the wash motor to the upper spray arm. Assuming\015\012the top spray arms are clear of debris, remove the lower spray arm to\015\012access the wash motor. Remove the 4 torx screws ... Kenmore 13742 / 13744 / 13749 Built-in Dishwasher

My Kitchen Aid KUDS01DJSS0 seems to have water going to the upper spray arm (I see water coming out of the unit just beneath the upper rack), but the pressure doesn't seem to be high enough to clean the upper rack. No evidence that water is coming out of the spray arm on the very top. Lower rack dishes seem to clean OK. I have already removed the whole upper spray arm assembly and inspected the flapper valves that the middle sprayer goes into. I suspect that it's not making good enough contac


... KitchenAid Dishwashers

Noticed dishes on top shelf not entirely clean. Ran machine empty and opened many times during wash. Noticed that Lower Spray Arm works as expected, but Middle Spray Arm turns only 1/8 or less, then Lower Arm spins again. Schematic with Use and Care manual just says pump motor switches from one to the other in certain cycles, but I don't see this happening. Looked for obstructions to water flow and pressure seems normal. Is control for this function part of the pump, or in the control panel?


Something could be in that checkball, see page 5 ... Frigidaire 24 in. GLDB653A Built-in Dishwasher

Kitchenaid dishwasher - small pieces of food are left on otherwise clean dishes. Water level comes to about 1 inch below heater coil. I ran it without dishes (or soap) and added about a quart of water so that level came to about 1/4 inch below heater and that's when I noticed food pieces on drain surfaces (nylon filter under bottom spray arm unit and circular plastic "trap" surrounding it). Spray arms holes are clear and water is hot.


It sounds as if you figured the solution out. The holes in the spray arm(s) get plugged by small debris, (tooth picks, seeds, bits of plastic like candy wrappers, etc) and the water does not reach the dishes to wash and rinse effective ... Dishwashers

Top rack not cleaning. How do I check to see if the spray arm is getting water, put toothpaste in the spray arm holes?


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Whirlpool GU2400XTP Built-in Dishwasher

KitchenAid kudj230ywh1 upper spray arm not spinning. Spins freely when I spin it. Checked for blockage in spray arm and don't see anything. Thoughts?


... KitchenAid KUDR25 Dishwasher

My dishwasher is not working properly, i have cleaned all the filters and spray arms, but still have food partials all over dishes. I did use a knife to hold down door latch so i could see what was happening when the dishwasher is working. Water does come out of the spray arms but they don't move and the dishwasher is empty, also now the latch won't catch since i used the knife.


Make sure the water temp is not too low. Make sure the pump is not clogged up with debris Check that hoses and spray arms are all clear. Remove spray arms and clean the holes in them. Make sure the shafts spins that the arms attach to. ... Bosch 24 in. SHE44C05UC Stainless Steel Built-in Dishwasher

My dishwasher spray arms were clogged with calcium buildup so I cleaned one and replaced the other. I also removed the fixed disc-shaped device underneath the lower spray arm and found the particle filter was clogged- so I cleaned it out. The dishwasher ran fine for a few times but then the filter clogged again, and again, and again. Now I need to make a routine of disassembling the parts to get at the filter every week because the filter no longer clears itself during the wash and/or emptying c


You may want to check your hot water tank. It may need drained and cleaned, Or you may have the rod in the tank disintegrating. Also check you water faucet areators to see if they have calcium pieces too. ... Maytag Dishwashers

Mod #: MDB6600AWB Ser #: 16505148CG No water comes out of spray arms, checked and cleaned filter-OK. Wash impeller is cracked where it slides onto the hexagon rod but it you take the filter flow plate off and put the impeller back on, when you put the unit on rinse only and quickly open the door you can see it is still turning and moving the water. The unit still fills and drains. it just does not have enough force with the impeller to force the water into the spray arms.


Hi,\015\012 \015\012Please check the bellow link regarding your query....\015\012 \015\012 ... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

I have a whirlpool GU2700XTSQ1 dishwasher. I have the typical top rack not cleaning problem. I have removed the rear washer tube that leads to the top sprayer, no clogs. Upper arm is clear, lower arm is clear. I also removed the lower cover, checked the chopper screen and inlet, no clogs. There is a screen inside that I cannot get to. It appears to have some sort of paper or cloth sticking through the screen with a 50% block. Perhaps a sticker or label from a dish. I see this screen when looking


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Whirlpool GU2700XTSB / GU2700XTSQ / GU2700XTST Built-in Dishwasher

My kitchenaid dishwasher leaves food particles on the dishes. There's supposed to be an "Ultra-fine filter" under the spray arm. Perhaps it is clogged, but I don't see how to remove the spray arm so I can check it and clean it. The owner's manual is no help. Can you tell me how to do this?


... KitchenAid Dishwashers

My maytag dishwasher lower and upper spray arms are working intermittently. Sometimes there is plenty of water spraying around, other times, I can hear what sounds like the motor running but the arms are not moving (or not moving much) and very little water is splashing around. When this happens, the detergent sometimes doesn't even get washed out of its compartment.


Pour 1 Cup of Muriatic Acid (Can be purchased at your local Pool Supply Store) into the bottom of the washer and a little in the soap dish. Run the Dishwasher through 5 cycles. Check to see If this helps. If not Try the same process with CLR house cl ... Maytag 24 in. MDB4000 Built-in Dishwasher

The disk washer doesn't drain at the end of the rinse cycle. There is a humming sound but no water is forced through the hose to the sink/garbabe disposal. At the end of the wash, there is a large amount of dirty water in the bottom of the washer. I removed the spray arms, the spray arm holder and the screen and then removed the water, and found a couple of pieces of plastic. But I don't see how I can remove additional parts from the washer bottom. What could the problem be? Is there a fi


Is the dishwasher drain hooked to the garbage disposer? If so is it new? If so did you knockout the plug in the disposer? If so then you either have something clogging the drain or pump. Or the pump motor is bad. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0575 seconds